Salus SS881ZB Quick Install Manual

Other manuals for SS881ZB: Installation And Quick Start Manual
Manual is about: Door/window sensor

Summary of SS881ZB

  • Page 1

    ϭ ^hϮϭ tŝƌĞůĞƐƐŽŽƌ^ĞŶƐŽƌ Θ ^hϮϭ tŝƌĞůĞƐƐtŝŶĚŽǁ^ĞŶƐŽƌ yƵŝĐŬ/ŶƐƚĂůů'ƵŝĚĞ.

  • Page 2

    Ϯ.

  • Page 3: Dăďůğžĩžŷƚğŷƚɛ

    ϯ dĂďůĞŽĨŽŶƚĞŶƚƐ zĞĂĚƚŚŝƐďĞĨŽƌĞƵƐĞ .................................................................................................................... ϰ ^ƚĂƌƚ,ĞƌĞ..................................................................................................................................... ϱ ϭ...

  • Page 4

    ϰ zĞĂĚƚŚŝƐďĞĨŽƌĞƵƐĞ • zĞĂĚƚŚĞƐĞŝŶƐƚƌƵĐƚŝŽŶƐĐĂƌĞĨƵůůLJďĞĨŽƌĞƵƐĞĂŶĚŬĞĞƉŝƚŝŶĂƐĂĨĞƉůĂĐĞĨŽƌĨƵƚƵƌĞ ƌĞĨĞƌĞŶĐĞ͘ • &ŽƌŝŶĚŽŽƌƵƐĞŽŶůLJ͊ • ůůŵĂŶƵĂůͬƐĂĨĞƚLJŝŶƐƚƌƵĐƚŝŽŶƐĂŶĚĞůĞĐƚƌŝĐŝƚLJƐƵƉƉůŝĞƌ͛ƐƌĞŐƵůĂƚŝŽŶƐŵƵƐƚďĞĨŽůůŽǁĞĚ͘ kƚŚĞƌǁŝƐĞŝƚŵĂLJĐĂƵƐĞĂĐĐŝĚĞŶƚƐŽƌĚĂŵĂŐĞƚŚĞƉƌŽĚƵĐƚ͘ • ŽŶŽƚŝŶƐƚĂůůƚŚŝƐƵŶŝƚĂƚĂŶĂůƚŝƚƵĚĞŽĨŽǀĞƌϮϬϬϬŵĞƚƌĞƐ...

  • Page 5: ^ƚăƌƚ,ğƌğ

    ϱ ^ƚĂƌƚ,ĞƌĞ 1. ‡–—’–Š‡‡•‘”‹–‘‹‰‡‡‡–™‘” • make sure the icontrol-hub is powered up and connected to internet before device pairing. • prepare the door/window sensor but do not power up them before getting ready on below steps. ϭ͘ϭ • access on the website: https://pdev.Icontrol.Com/sp/login.Jsp • ...

  • Page 6

    ϲ.

  • Page 7

    ϳ • click on button “add door/window sensor” • click on “next”: • icontrol server enters to pairing mode. • till this step, the system gets ready for the sensor joining to the network. It’s waiting for any sensor to join its network. This waiting would be timed out after 5 minutes if there was no ex...

  • Page 8

    ϴ ϭ͘ϯ • pulling out the insulation tape can energize the door/window sensor to scan netwrok and subsequently paired to the network successfully. The sensor will take below rules for its joining: (a). It will scan all channels every 5 seconds and will try to join any available network. For each scann...

  • Page 9

    ϵ ϭ͘ϱ •‹‰‘ˆ–Š‡‹†‘™•Ȁ‘‘”‡•‘”ǣ on the “home” page, you can see all of your devices. Within the “sensor” group, your sensors were listed there. For example, along with the window sensor magnet part close/ apart, it will show the closed/open state on the list immediately, also with a historical log f...

  • Page 10

    ϭϬ 2. Paramater function supporting profile ha 1.2 and above. Icontrol compatible. Supporting clusters basic cluster identify cluster power configuration cluster poll control cluster temperature measurement cluster commissioning cluster diagnostics cluster ota cluster ias zone cluster ez-mode bindin...