1. DL manuals
  2. Samsung
  3. Air Conditioner
  4. AJ036JCJ5 Series
  5. Installation Manual

Samsung AJ036JCJ5 Series Installation Manual

Summary of AJ036JCJ5 Series

  • Page 1

    Mqt†vœ›‹––™ghqwz]qjq\†pt†lu†ki]_tw\wxzhtwwu•‹‹gggzy ywx[txytx^ggg㝘㤸gxxa\[a\].

  • Page 2

    Air conditioner installation manual imagine the possibilities thank you for purchasing this samsung product. Aj036jcj5** en es fr db68-05013a-00 mqt†vœ›‹––™ghqwz]qjq\†pt†lu†ki]_tw\wxzhtwwu•‹‹gggzz ywx[txytx^ggg㝘㤸gxxa\[a\].

  • Page 3: Contents

    2 contents safety precautions .................................................................................................................................................................................................................................2 accessories ..................................

  • Page 4: Safety Precautions

    3 english safety precautions g eneral information x do not attempt to repair, move, alter or reinstall the unit. If performed by unauthorized personnel, these operations may cause electric shocks or fires. X do not place containers with liquids or other objects on the unit. X all the materials used ...

  • Page 5: Accessories

    4 a accessories the following accessories are supplied with the air conditioner. Accessories in the outdoor unit case ※ attach energy label to the outdoor unit properly when installing. 䭭 the 3-wire power cable and the 2-wire assembly cable are optional. If these cables are not supplied, use the sta...

  • Page 6

    5 english ◆ you have just purchased a free joint multi air conditioner and it has been installed by your installation specialist. ◆ this device must be installed according to the national electrical rules. ◆ max input power & current is measured according to iec standard and input power & current is...

  • Page 7

    6 a space requirement for outdoor unit when installing 1 outdoor unit 300(12) or mor e ※ when the air outlet is opposite the wall 1500(60) or mor e ※ when the air outlet is towards the wall 300(12) or mor e 300(12) or more 600(24) or more ※ when 3 sides of the outdoor unit are blocked by the wall 15...

  • Page 8

    7 english 1. Position the outdoor unit so that the air flow is directed towards the outside, as indicated by the arrows on the top of the unit. 2. Attach the outdoor unit to the appropriate support using anchor bolts. ◆ the earthing wire for the telephone line cannot be used to earth the air conditi...

  • Page 9

    8 a ◆ piping length and the height ◆ piping outside diameter ※ the appearance of the unit may be different from the diagram depending on the model. Main power switch a c b d e (h) (h) make at least one round : it will reduce noise and vibration indoor unit outdoor unit power supply ø, v, hz **007/00...

  • Page 10: Refrigerant Piping Work

    9 a english 1. Make sure that you have the required tools available (pipe cutter, reamer,flaring tool and pipe holder). 2. If you wish to shorten the piping, cut it using a pipe cutter, taking care to ensure that the cut edge remains at a 90° angle with the side of the pipe,and referring to the illu...

  • Page 11: Refrigerant Piping Work

    10 a follow different orders depending on the capacity of indoor units. **007/009/012** ◆ install pipes between indoor and outdoor units orderly as [a→b →c→d→e]. **018/024** ◆ install pipes between indoor and outdoor units orderly as [ c→d→e]. 1) use tube connector (pipe 12.70 mm(1/2"), bolt 9.52 mm...

  • Page 12

    11 english checking gas leakage before completing the installation (insulation of the cables, hose and piping and fixing of the indoor unit to the installation plate), you must check that there are no gas leaks. Leak test with nitrogen (before opening valves) in order to detect basic refrigerant lea...

  • Page 13: Method For Connecting Wires

    12 method for connecting wires pump down (before disconnecing the refrigerant connections for unit repair, removal or disposal) pump-down is an operation intended to collect all the system refrigerant in the outdoor unit. This operation must be carried out before disconnecting the refrigerant pipe i...

  • Page 14: Method For Connecting Wires

    13 a english method for connecting wires specification for circuit breaker and power supply cord 䭭 power supply cord is not supplied with air conditioner. 䭭 select the power supply cord in accordance with relevant local and national regulations. 䭭 wire size must comply with the applicable local and ...

  • Page 15: Method For Connecting Wires

    14 carbon plastic steel core pvc-insulated green /yellow wire, 2mm² x 3.5m(11.5ft) to earthing screw 50 cm(1.6 ft) 30 cm (1 f t) 1. Select an earthing electrode that complies with the specifications given in the illustration opposite. 2. Determine a suitable location for the earthing electrode : ◆ i...

  • Page 16: Setting Indoor Unit Address

    15 a english setting indoor unit address automatically setting indoor unit address ◆ switch the system on and wait for code " " to appear on the display of the external unit (this requires approximately 60 seconds **). ◆ as soon as code " "displays, press once the red button (k1) shown on the figure...

  • Page 17: Setting Indoor Unit Address

    16 a step 1 review all the following elements in the installation: ◆ installation site strength ◆ piping connection tightness to detect any gas leakage ◆ connection wiring ◆ heat-resistant insulation of the piping ◆ drainage ◆ earthing wire connection step 2 important! Before selecting switch, turn ...

  • Page 18

    17 english rotary switch “sw02” position according to refrigerant circuit connected ( 0=a; 1=b; 2=c; 3=d; 4=e ) indoor unit sw02 att. "a" att. "b" att. "c" att. "d" att. "e" a unit b unit c unit d unit e unit outdoor unit type picture model to set addressing manually by rotary switch “sw02” slim duc...

  • Page 19: Setting Indoor Unit Address

    18 a high temp button high fan button mode change low temp button low fan button entering mode for setting option option setting mode x setting option 1. Remove batteries from the remote controller. 2. Insert batteries and enter the option setting mode while pressing high temp button and low temp bu...

  • Page 20

    19 english operation indication * step 1 1. Remove the batteries from the remote controller. 2. Insert batteries while pressing high temp button and low temp button. * step 2 1. Press low fan button to enter seg2 value. 2. Press high fan button to enter seg3 value. * step 3 press mode button to be c...

  • Page 21: Setting Indoor Unit Address

    20 a 1. Check whether power is supplied or not. - when the indoor unit is not plugged in, there should be additional power supply in the indoor unit. 2. The panel (display ) should be connected to an indoor unit to receive option. 3. Before installing the indoor unit, assign an address to the indoor...

  • Page 22

    21 english • when “a”~”f” is entered to seg4~6, the indoor unit main address is not changed. • if you set the seg 3 as 0, the indoor unit will maintain the previous main address even if you input the option value of seg4~6. • if you set the seg 9 as 0, the indoor unit will maintain previous rmc addr...

  • Page 23: Setting Installation Option

    22 a ampere limit setting & changing procedure ampere switch selection aj036jcj5** switch 3 4 23a 2)) on on 20a 2)) on off 18a 2)) off on 16a 2)) off off it could take maximum 60 minutes to operate for the protection of the compressor if the outdoor temperature is below -5 °c(23 °f). Setting install...

  • Page 24

    23 english settings of pcb display of the outdoor unit ◆ key options of pcb display - k1 : pipe checking operation button - k2 : function button - k3 : reset button - k4 : view mode change button key push k1 k2 k3 k4 1 pipe checking operation (display: ) heat mode try run (display: ) reset view mode...

  • Page 25

    24 a installing transmitter and sub pcb for central control accessories (transmitter : mim-b13b) 1. Turn the power off and take off the cover of the outdoor units. 2. Fix the case with bolts to the side of the control box referring to the figure on the right side. In case of fjm outdoor unit, there ...

  • Page 26

    25 english sub pcb installation (optional) if indoor unit is aj***jnad**, install sub pcb. (wired remote controller, central remote controller etc.) 1. Turn the power off and remove the cover panel of the indoor unit. 2. Attach the sub pcb to the case sub pcb. 3. Install the case sub pcb to the indo...

  • Page 27

    26 a 1. Check whether power is supplied or not. - when the indoor unit is not plugged in, there should be additional power supply in the indoor unit. 2. The panel (display) should be connected to an indoor unit to receive option. 3. Before installing the indoor unit, assign an option to the indoor u...

  • Page 28

    27 english ▶ if you input a number other than 0~4 of the individual control of the indoor unit(seg20), the indoor is set as "indoor 1". 1) the window on/off function applies to the following unit option seg1 seg2 seg3 seg4 seg5 seg6 explanation page mode central control indication and details indica...

  • Page 29

    28 option seg13 seg14 seg15 seg16 seg17 seg18 explanation page use of external control setting the output of external control s-plasma ion buzzer control number of hours using filter indication and details indication details indication details indication details indication details indication details...

  • Page 30: Test Run and Final Check

    29 english test run and final check test run final check and explaining operation to the owner 1. Please do cool mode try-run or heat mode try-run. ◆ cool mode try-run : push the [k2] button three times. ◆ heat mode try-run : push the [k2] button once. 2. After 12 minutes of stationary condition che...

  • Page 31: Troubleshooting

    30 a troubleshooting ◆ the error indicated on the pcb display of outdoor unit display explanation (the error indicated on the pcb display of outdoor unit) remark communiaction error(indoor unable to receive data) check electrical connection and setting outdoor unit communication error(abnormal data ...

  • Page 32

    31 english display explanation (the error indicated on the pcb display of outdoor unit) remark evaout1 sensor short/open evaout2 sensor short/open evaout3 sensor short/open evaout4 sensor short/open evaout5 sensor short/open outdoor unit freezing(compressor stop) check pipe length, indoor unit filte...