SVP CDC-7530 Quick Start Manual

4

1

165mm+-2

4

1

4

1

3

6

2

5

1

2

2

m

m

+

-2

R9000348

Cautions

  How to Connect with a Computer

How to Connect with a TV

    Turn On or Off the Camera

Loading the Batteries

Quick Start Guide

Icon Introduction

Printer / TV Connection

        PC Connection

Getting Ready

Getting Ready

1. Connect the video-out jack of the camera to video input ports

    of the TV set with the supplied Video/USB Cable.

2. Turn on the TV set and set the TV/Video switch to A/V mode.   

3. Power on the camera and then enter the Playback Mode. 

4. Press down the LEFT or RIGHT direction Button to go to the 

next or last image for TV reviewing. 

1. When the USB/Video Cable is in connection with the computer while the camera is on, the camera will automatically go to the      

    PC Mode from any working mode and  turn off  TFT LCD monitor as well.

2. In this Mode, you can download images from your computer .  

1.

R9000348     2.

Pantone 316U

  3.

80P 

,Z

Do not try to open the camera by yourself, which may damage the camera or cause electric shock.

Do not fire the flash in a close distance (less than 1 meter ) because it may hurt your eyes. 

Keep the camera away from the reach of children or animals to prevent them from swallowing the batteries or small accessories. 

Stop using the camera if any kinds of liquid enter the camera. If it happens, power off the camera and contact the your dealer  for 

further help. 

Do not use this camera with wet hands, which may cause electric shock as well. 

Putting  the camera in a high temperature environment may damage the camera. 

Do not use different types of batteries or new and old batteries at the same time. 

To avoid electricity leakage, please remove  the batteries  if  the camera is not in use for a long period. 

It is normal that the temperature of the camera body rises if the camera is used for a long time.

Press down the "POWER" button  to turn on the camera.

Repeat the way above  to turn off the camera.

+

Positive

-

Negative

1. Slide out Battery Cover to open it. 

2. Load 2 x AA batteries into the battery chamber, following    

    the polarity indications.

3. Close the Battery cover.

2 pcs of AA alkaline / Ni-MH batteries are strongly 

recommended for normal operation.

Batteries may lose power if kept inside the camera for a long 

time without using. Please remove the batteries while the 

camera is not in use.

Do not use manganese batteries since they cannot supply 

sufficient power to support the camera's operation. 

Batteries may not work normally under 0 C or over 40 C .

It's normal that the temperature of the camera  goes up after 

being in use for a long period.

    The below symbols on the TFT LCD Monitor are the indication 

    of the battery status.  

(     ):Battery power is full.

(     ):Battery power is half drained. Have new batteries ready. 

(     ):Battery power is drained. Replace the batteries you are 

         using now. 

8

8

3

5

6

1

2

7

4

Green (Focus is ready)

1M

14

1M

14

RED (Focus Adjustment)

Blinking

100-0021

8

Basic Photography

1. Press down the POWER button to turn on the camera.

2. Set the Mode Switch at Image Shooting Mode (      ) for still image or Movie Clip Mode  (      ) for video recording. 

     NOTE: Hold your camera with your hand and position a subject in the center of the frame to focus on.

3. With the TELE/WIDE Button, you may have 3.0X optical zoom and 5X digital zoom for zooming in and out. 

4. Press and hold the shutter button halfway down. 

     NOTE: 1. When the color of the focus frame turns from white to red, it means the auto focus of this camera  is not fixed.

            2. When the color of the focus frame turns from white to green, it means the auto focus of this camera  is fixed.

5. Press the shutter button fully down to capture an image. 

6. The LED Indicator starts blinking right after the Shutter Button is released.  Once the LED Indicator stops blinking, you are     

ready to take another shot.

7. Or you can set Mode Switch at Playback Mode (      ) to view the images or movie clips you just took. 

 Battery Status

(    )Battery Full

(    )Battery Half 

Drained

(    )Battery Drained

 Working Mode

(    )Image 

Mode

Shooting 

(    )Night Scene Mode

(    )Photo Frame Mode

(    )Movie Clip Mode

(    )Voice Recording 

       Mode

1

2

  Flash Mode

(     )Auto Flash

(     )Auto Flash with 

Red-eye Reduction

(     )Slow Sync 

(     )Fill-in Flash  

(     )Flash Off

4

 Self-timer

(    )10 Seconds

(    ) 2 Seconds

(    )Double

2S

5

3

(    )Hand Shake

(    )Playback  Mode

 Memory 

Card

(    )

 White Balance

(    )Auto

(    )Daylight

(    )Cloudy

(    )Fluorescent

(    )Tungsten

(    )Sunset

(    )Custom

11

12

 Sharp

(    )Soft

(    )Normal

(    )Vivid

 Quality

(    )Super Fine

(    )Fine

(    )Normal

13

14

 Voice 

Memo

(    )

 Focus Range

(    )Macro

 Metering

(    )Spot

(    )Multi

+

 Exposure

0

-

(    )

6

7

8

10

 Continuous Shooting

(    )Single

(    )2 Shots

(    )4 Shots

(    )8 Shots

9

1

2

4

8

Digital 

                Zoom

(            ) 

3.0X Optical/

                5.0 X 

    Zoom In / Out 

   Indicator

17

 Available 

Shots

( 7 ) 

16

5

7

1

2

4

5

6

8

5M

17

3

10

11

12

13

14

15

16

7

2

9

X 1.2

 Size

(      )2560x1920

(      )2304x1728

(      )2048x1536

(      )1600x1200

(      )1024x768

15

(      )3072x2304

Connecting the Camera to a PictBridge-supported Printer

If the printer you have supports the interface of PictBridge, then you may have your camera connected 

with  the printer with the supplied USB cable and have the stored images print out directly.

1.Have both of the camera and the printer power on. 

    2. Press the MENU Button to go to SETUP Mode.

    3. Go to PRINTER and select USB for printer connection.    

    4. Use the supplied USB cable to connect the camera to the 

        PictBridge-supported printer as shown above.

Desktop