Part# tc30.Ng01.C for tc30 series c important: these instructions are to remain with the homeowner these instructions are supplementary to the installation and operating instructions supplied with the fireplace and should be kept together. Refer to the installation and operating instructions for pro...
2 tc30.Ng01.C 140708 notes.
1. Attach the burner assembly to the floor of the firebox with two screws. (fig. # 1). 2. Attach the manifold supply tube to the bulk head fitting and tighten. (fig. # 2) ensure that there are no leaks. Note: primary air shutter must be fully closed for natural gas or fully open for propane. Burner ...
5. Position the grate over the burner tray and attach to the floor with two screws through holes located behind the front legs of the grate. (fig. # 5) 6. Attach air deflector to rear of grate with two screws (fig. # 6) 3. Attach the pilot supply tube to the bulk head fitting and tighten. (fig. # 3)...
A large bag of ember material is shipped with the fireplace and needs to be installed to ensure optimum performance and flame appearance. 1. Pull apart the material into ember size pieces (approximately 1” squares) and gently place them into the burner pan. Do not compress, leave them loose for best...
Base log #1 pin hole pin hole pins top right log #2 pin stop tab fig #8 fig #9 fig #10 fig #11 fig #12 the logs are packaged in a foam pack inside the box. They are fragile and should be handled with care. Unpack and inspect log set. There should be a total of 7 logs. Gas plumbing and vent con- nect...
Pin hole top left log #3 bottom rhs chunk #4 bottom center chunk #5 bottom lhs chunk #6 center chunk #7 fig #13 fig #15 fig #14 fig #16 fig #17 fig #18 7 tc30.Ng01.C 140708.
If the unit is to be used on propane convert as follows using the components supplied with this burner: caution the gas supply and electrical power shall be shut off before proceeding with the conversion. Note: factory supplied components must be used to ensure correct input. After conversion confir...
The minimum rate screw is sealed with an o-ring. Use a thin bladed screwdriver to back the screw out to the limit of the threads. A groove on the screw body will be visibe just above the valve body. Insert a thin tool (knife blade or thin screwdriver blade) into the groove and gently pry the screw u...
12. Replace the minimum rate screw with the one provided in the propane conversion kit supplied with this fireplace. Ensure that the screw is fully installed. (fig. #29) 13. Pull off the rubber cap from the top of the pressure regulator. (fig. #30) 14. Press down on the center post and rotate 90°. T...
1. Remove the plug from the pressure test port using a 7/16” socket and extension . The plug is located between the right side lintel and firebox side (bottom port). (fig. #33) 2. Thread the extension test fitting into the open test port. (fig. #34) 3. Attach a pressure gauge onto the fitting. 4. Wh...
Caution: proper air shutter setting is a must. The flame should be just orange and “lazy”. It should never be set to create sooting on internal parts and glass. Caution: burner area may be hot! Turn off the fireplace and allow the unit to cool before proceeding. To adjust: 1. Open and remove window ...
4 5 6 1a 1b 1c 1d 1e 1f 1g 1h 1i 1j 2a 2b 2c 2d 2e 2f 2g item .......Description ............................................Part no. #1..........Chalet burner assembly ......... Tc30.Ng01.C #2..........7 pcs log set ................................. 5098.746148 #3..........Orifice, natural gas (#32...
14 tc30.Ng01.C 140708 notes.
15 tc30.Ng01.C 140708 notes.
Printed in canada technical support: 1-877-715-2664 web site: www.Townandcountryfireplaces.Net 2975 allenby rd., duncan, bc v9l 6v8.
