T&M PROJECTMIX818 User Manual - page 10

Summary of PROJECTMIX818

  • Page 1

    Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference. Projectmix818 o p e r a t io n m a n u a l zone select output level function page all enter bgm all esc power monitor source up source d...

  • Page 2

    Be sure to read the instructions in this section carefully before use. Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included. We also recommend you keep this instruction manual handy for future refer...

  • Page 3

    An all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building. When installing the unit never plug in nor remove the power supply plug with wet hands, as doing so may cause electric shock. When unplugging the pow...

  • Page 4

    Contents 1.Introduction ................................................................................................ 1 2.Front panel layout ................................................................................... 1 3. Rear panel layout ....................................................

  • Page 5

    1. Introduction select source zone led display monitor zone select page busy mic priority indicator mic priority button music volume master volume mic volume page all monitor led display monitor zone output level monitor volume esc enter bgm all the matrix & paging controller family comprise an 8 ch...

  • Page 6

    1. Source select 2. Zone led display 3. Page busy the source select button (1) is used to select the source for the zone. Each zone has a separate source selection button. There are 9 selectable sources: line sources 1 through 8 and a local in wall mixer or source select/volume control)can beconnect...

  • Page 7

    9. Monitor zone select note: 11. Monitor zone output level the zone select button (9) is used to select one of the 8 zones to be monitored.Pressing the zone select button will cycle through allzones in sequence as follows:1,2,3,4, 5,6, 7, 8, and off. Button.Once the display shows the desired zone, p...

  • Page 8

    - + db gain hf lf page gain -10 +10 db -10 +10 db lf hf microphone 1 extension link gain -8 +8 db -8 +8 db db output - + db gain hf lf page gain -10 +10 db -10 +10 db - + db zone 8 gain hf lf page gain -10 +10 db -10 +10 db db - + db - + db - + output output zone 2 zone 3 disable enable disable enab...

  • Page 9

    Each zone can have a remote line level source connected. The remote source input connector is shown here. 6. Remote source 2. Evac / fire system interface (7 way pheonix connector) pin 6 - [emc in] 3. Tone output 4. Emc input 5. Extension link (db37 connector) the built-inalertvoice message will be ...

  • Page 10

    The zone lf bass of the zone output can be controlled by adjusting the lf bass level control. This level control will provide adjustment of the 100hz audio frequency by ± 10db. Every zone has a lf bass level control which enables the lf bass level of each zone to be set independently of other zones....

  • Page 11

    The system line source input signal levels can be adjusted from 190mv to 200mv using the line source input gain control. This will enable the signal level of all sources to be equalized there by ensuring output volume level remains constant when switching from one source to another source. All syste...

  • Page 12

    8 1. Rs485 b 2. Rs485 a 3. Gnd 4. + 24v (out) 5. Gnd 6. + 24v (out) 7. Mic in + 8, mic in- 19. Paging mic gain 20. Mic1 input the balanced mic1 input xlr type has an impedance of 600ohms. Each zone has amic1 priority button. Each zone has a mic1 priority button.When the mic1 priority button is not e...

  • Page 13

    Status data to paging console inquiry data to remote wall plate ha 1 e matrix address code zone data am aa: data head 1 e: zone status feedback to paging console matrix address code= 01 : master matrix 02: extension matrix 1 03: extension matrix 2 04: extension matrix 3 zone data: the zone data is i...

  • Page 14

    Aa 21 line input volume am aa: data head 21 : feedback data from wall plate to matrix line input: source input 01 : line 1 02 : line 2 08 : line 8 09 : remote sources input volume: volume level 00 : 0 level 01:1 level am: (accumulation= 2nd data byte + 3rd data byte + 4th data byte) inquiry data to ...

  • Page 15

    6. Connection diagram remote control pancls master matrix 8 remote control panel extension matrix 1 8 remote control panel extension matrix 2 8 remote control panel 1-8 zone speaker outputs 9-16 zone speaker outputs 17-24 zone speaker outputs 25-32 zone speaker outputs line 1-8 inputs extension matr...

  • Page 16

    12 there are 4 address codes on both remote the paging console and the extension keypad which are used to identify these. Only one address code switch of each dip switch can be placed in the downward position.If any of the dip switches are set at different addresses to those shown above, the console...

  • Page 17

    Versionv0.1.