TA Service Indoor Wave Instructions Manual

Summary of Indoor Wave

  • Page 1

    1 art.Nr: 95346 ta. Service a/s · centervej syd 2 · dk-4733 tappernøje tlf +45 56 72 57 77 · fax +45 56 72 57 76 · www.Ta-service.Dk ver. 2.3 eng 2015.

  • Page 2

    2 1 warnings. Read the instructions carefully. It contains important warnings and instructions. Do not reach into or under the chair when the seat lift and seat tilt is activated, because there is a risk of entrapment between the mechanical parts. Be aware of others, especially children, is too clos...

  • Page 3

    3 2 preface ta services a/s hope you are satisfied with your new ta indoor wave. Ta indoor wave is designed to facilitate your daily movement indoors and outdoors close to your home. It has been very important to design the chair as small and compact as possible, without reducing the chair's stabili...

  • Page 4: Contents

    4 contents 1 warnings. ................................................................................................................................................... 2 2 preface ........................................................................................................................

  • Page 5

    5 4 technical data wheelchair type: class a: wheelchairs mainly intended for indoor use and are not necessarily doing outdoor hurdles. Dimensions: width excl. Seat: 56 cm length excl. Footplate / foot supports: 69.5 cm length incl. Standard footplate: 88.5 cm diagonal excl. Standard footplate: 90 cm...

  • Page 6

    6 charger specifications: see user's guide included charger - 24v / 5 a. Electronics: penny and giles r-net drive control brakes: motor brake and electric brake. Motor brake acts as brake-lock brakes, and is activated when the control stick is released. From you release the control stick and until t...

  • Page 7

    7 5 before driving : warning! Ta indoor wave is not intended for users with a weight exceeding 125 kg warning! Ta indoor wave should be turned off when making entry and exit of the chair and when assisted by a helper, so that the chair does not accidentally run if the joystick is activated. Footplat...

  • Page 8

    8 5.1 performance check the electronic circuits in your control system have been designed to be extremely safe and reliable. The on- board microcomputer carries out safety checks at up to 100 times per second. To supplement this safety monitoring you should carry out the following periodic checks. I...

  • Page 9

    9 5.3 getting in and out of the wheelchair ! Before getting in and out of the wheelchair, make sure that the wheelchair is turned off. If the user can transfer itself, lower the tilt and the lift to the lowest position. For transferring from the front tilt the footplate up figure 1 for sideways tran...

  • Page 10

    10 6 while driving: ta indoor wave's driving characteristics including: braking, maximum speed and acceleration can be set to suit the individual needs. Setting the chair's driving characteristics is performed by ta services a/s. 6.1 speed and profiles ta indoor wave is switched on by a light pressu...

  • Page 11

    11 6.3 mechanical disengaging the brakes. The brake can be disengaged by the need for manual towing. This is done by twisting the brake handles away from ta indoor wave logo onto the wheels in both sides. Figure 1 when the brake is released, the chair cannot be moved with the control stick. This can...

  • Page 12

    12 6.6 driving on slopes. Driving on sloping surfaces should be carried out forwards and at a slow pace. Never exceed the max safe slope as described under technical data sheet warning! Driving on slopes should be avoided because a slope to the site will give a risk that the chair can tip over. When...

  • Page 13

    13 8 controller/adjustents 8.1 controller 1 power button 2 horn 3 light* 4 hazard* 5 display 6 profile 7 switching between driving and menu 8 speed up button. 9 speed down button. 10 right indicator light* 11 left indicator light * * - accessories on some versions display 1 - battery indicator: 2 - ...

  • Page 14

    14 electric back – figure c electrical functions – figure c pressing the "mode" button to get into the menu from which electrical functions can be operated with a joystick. You select function by flipping the pages with the joystick, and activate the feature by taking the control stick forward or ba...

  • Page 15

    15 8.3 setting menu in the setting menu it is possible to change the clock, brightness, backlight and color, and odometer. To get into the options menu you must hold both buttons speed up and speed down simultaneously. See arrow a - figure 1 the following points are then displayed in the menu: (figu...

  • Page 16

    16 8.4 setting the power functions the wheelchair may depending on model have the following power functions: seat lift seat tilt back right legsupport left legsupport the functions are activated by pressing the "mode" button on the control box, then there's a picture of power features (figure 1). Fi...

  • Page 17

    17 9 alternative controls/functions 9.1 controller without display joystick buttons 1 power button 2 horn 3 switching between driving and menu 4 driving profile 5 speed up button. 6 battery indicator 7 function indicator 8 speed down button. ! For light see section “controller” on/off switch. Batter...

  • Page 18

    18 red, yellow and green light (1-10 lights: this indicates all is well. Red and yellow light (1-7 lights): the control system is functioning correctly, but you should charge the battery as soon as possible. Red lights (1-3 lights constant or flashing): the power chair must be charged immediately no...

  • Page 19

    19 10 adjustments 10.1 setting the armrests. Armrest cushion position relative to the back is adjusted by loosening the 2 screws under the horizontal tube with a 4 mm allen key (a1), and the 2 screws in the c-profile with a 6 mm allen key (a2) armrest height is adjustable by loosening screws (b) on ...

  • Page 20

    20 10.3 setting up the leg rest. The leg rest is mounted on the chairs seat frame. Leg rest position relative to the seat is adjusted by loosening the 2 bolts on both sides of the power chair with a 6 mm allen key (a). Pull or push the leg rest and then tighten all 4 bolts again. The angle of the le...

  • Page 21

    21 11 transportation by car. Ta indoor wave is crash tested with 4-point car tiedown (accessories) and dahl docking system (accessories), so it can be used as a seat in the car, bus or similar. The user can use the ta indoor wave during transport by car, bus or similar, if the ta indoor wave is equi...

  • Page 22

    22 12 charging. Ta indoor wave is equipped with a battery level indicator at the top of the control box - the long series of leds. As the chair is used the battery level falls and the leds turn off. See the following explanation: battery indicator: all 10 bar lights (red, yellow and green): the chai...

  • Page 23

    23 13 disposal. Ta indoor wave must be disposed as electrical scrap, which means that the product cannot be disposed with ordinary waste. It has to be disposed of in an environmentally correct way. The product can be delivered to ta service or local dealer which will see that it is disposed of in an...

  • Page 24

    24 17 troubleshooting – controller with display problem: cause: solution: the power chair cannot run 1. Charging connector is connected to the control box. Remove the charging plug. 2. Motor brake is disengaged. Connect the motor brakes. 3. Other cause. Contact authorized service center. The chair d...

  • Page 25

    25 17.1 troubleshooting – controller without display if a system failure should occur, you can find the cause by counting the number of light diodes flashing – if light diodes lights constant – see chapter “controller without display” number of light diodes flashing: cause: solution: 1. Batteries ne...

  • Page 26

    26 18 service and maintenance a service manual is available for dealers and service agents – contact ta. Service for more information ta service recommends that the wheelchair get service at a dealer or at the factory of ta service. ! Maintenance and service that are not listed under service and mai...

  • Page 27

    27 18.3 fuse under the back shield in the left side is an overload protection (fig. 1). Fuse cuts power if the wheelchairs maximum consumption exceeds 50a the fuse is a circuit breaker that switches off at overload. To reconnected the fuse button is pressed which sits inside the shield (arrow a) fig...

  • Page 28

    28 18.6 tyre punctures: start by lifting the wheelchairs wheel free from the ground, either by using a lift or by putting something stable between the bottom frame and the ground. Figure 1 ! Tilt or lift only the wheelchair when the user is not in the wheelchair castors screw the nut off the bolt wi...

  • Page 29

    29 drive wheel lift the wheelchair – see introduction and figure 1 take the plastic cover off the nut with a screwdriver. Figure 5 loosen the bolt in the center of the wheel with a 17 mm socket spanner and pull off the wheel from the shaft. Figure 6 before splitting the rim, let the air out of the t...

  • Page 30

    30 when putting the wheel on the shaft again, be aware that the keyway on the rim shall fit at the keyway on the shaft. Figure 9 19 accessories and spareparts ta service is constantly developing various accessories. For more information about accessories and spare parts contact the local dealer or t...