Summary of EMERALD ICE

  • Page 2

    The information contained in this document is proprietary and is subject to all relevant copyright, patent and other laws protecting intellectual property, as well as any specific agreement protecting tadiran telecom, inc. (herein referred to as the “manufacturer”) rights in the aforesaid informatio...

  • Page 3

    Ii tadiran telecom pays careful attention to quality standards in the manufacture of all our products. Safety is a major factor in the design of every emerald ice key- set and system. However, safety is your responsibility, as well. Please read the helpful tips listed below and on the next page. The...

  • Page 4

    Iii • to reduce the risk of electric shock, do not disassemble this terminal. Emer- ald ice keysets have no user serviceable parts. Opening or removing cov- ers may expose you to hazardous voltages. Incorrect reassembly may cause electric shock when the terminal is subsequently used. Cleaning and se...

  • Page 5

    Important user safety instructions ........................................................... 1-1 emerald ice cordless handset ................................................................. 1-1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

  • Page 7: Introduction

    Introduction.

  • Page 8: Emerald Ice Cordless Handset

    Introduction page 1-1 introduction the emerald ice cordless ekt phone set connects to the emerald ice phone system to provide powerful and convenient cordless functions for the business user. Each handset is equipped with a charging unit that operates via 9vdc power adapter. Two ekt lines connect th...

  • Page 9

    Emerald ice corless handset quick start guide page 1-2 the system provides a simple setup function to install the cord- less system easily. The user simply presses and holds the [f1] key for 1 second. The system will then automatically enter the system programming mode. The lcd will display: when th...

  • Page 10

    Introduction page 1-3 the user can then use the above programming function keys to set up 3 different led flash cadences as follows: 1. Normal operation: led flashes [normally]: 500ms on, 500ms off, repeatedly. In normal mode, the user can make/receive a call by the handset unit through the base uni...

  • Page 11: System Registration

    System registration.

  • Page 12: System Registration

    System registration page 2-1 registration programming allows a handset user to register the handset to the base unit. In summary; 1. Power up the base unit andenter the registration mode on the base unit. 2. Select the handset and set it to registration mode. 3. Move the handset near the base. The s...

  • Page 13

    Emerald ice cordless handset quick start guide page 2-2 3. If the handset was never registered, the lcd will display the following message. Press and hold the [f1] key for 1 second to enter the sys- tem programming mode. The lcd will display: press [f1] or [f2] to select registration mode. Press [ok...

  • Page 14

    System registration page 2-3 you can select [yes] to register, or [no] to exit this mode. Press [f3] (the same as [ok] key) to confirm, the lcd will display: (e.G. [yes]) 4. Move the handset near the base. The system will start to register with the base unit. If the registration operation is success...

  • Page 15

    Emerald ice cordless handset quick start guide page 2-4 note: if the user wants to register again steps 1 through 5 above re-register to base unit. 6. Change the dip switch on the base changes to normal mode - switch-1, 2, and 3 are off. Note: the led on the base will flash [normally] when the unit ...

  • Page 16

    System registration page 2-5 note: the led on the base will flash [fast] when enter the de- registration mode. 2. De-register handset #1. Turn dip switch-3 to on, and switch-1 and switch- 2 to off. After 5 second, the system will de-register handset #1. Note: the led on the base will flash [fast] wh...

  • Page 17

    Emerald ice cordless handset quick start guide page 2-6 note: the led on the base will flash [normally] when the unit comes back to normal mode. Operation procedure for method-b (using the base and handset): 1. Verify that the base unit is in the idle mode. 2. With the handset in standby mode, press...

  • Page 18

    System registration page 2-7 press [f3] to confirm, the lcd will display: (e.G. [yes]). If the de-registration is successful, the lcd will display: if the de-registration fails, the handset lcd will display the following after 20-30 seconds: note: 1. Using the method-a or b, the system must be in id...

  • Page 19

    Emerald ice cordless handset quick start guide page 2-8 b) the handset unit must be moved to near the base to receive de-registration command from base unit. C) only one handset can de-register to the base at a time. 3. After de-registration, the handset lcd will display: 4. About the de-register, p...

  • Page 20

    System registration page 2-9.

  • Page 21: Programming The Handset

    Programming the handset.

  • Page 22: Programming The Handset

    Programming the handset page 3-1 the system provides a programming mode to set up user- friendly features. When a user enters the [system programming mode], all [soft keys] will be changed the following function key: [f1] key: [down] [f2] key: [up] [f3] key: [ok] [func]key: [program] [hold] key: [ex...

  • Page 23

    Emerald ice cordless handset quick start guide page 3-2 programming summary there following describes the programming available on the handset unit. In general, press the [program] key and then press [down/up] to select the item that you want to program. The following are the different items availab...

  • Page 24

    Programming the handset page 3-3 3. Press the [f1] key to change the item. (or, [f1/ f2] to select the other language): 4. Press the [f3] (the same as [ok] key) to confirm. The handset will generate a confirmation “beep”.The lcd will display: after 3 seconds, the lcd will return to the first program...

  • Page 25

    Emerald ice cordless handset quick start guide page 3-4 registration programming registration programming allows the handset user to register the handset with the base unit. 1. Enter the programming mode by pressing and holding the [f1] key for 1 second. The lcd will display: 2. After the handset be...

  • Page 26

    Programming the handset page 3-5 5. Press the [f3] key to confirm. The lcd will display: if the registration operation is successful, the lcd will display: note: you can refer to the part of system registration in the pre- vious section for further details. De-registration programming if a user does...

  • Page 27

    Emerald ice cordless handset quick start guide page 3-6 3. Press [f3] to enter the change mode. The lcd will dis- play: 4. Toggle the [f1/f2] keys to select the [yes?] mode. [yes] will de-register, [no] will exit this mode. 5. Press [f3] to confirm. The lcd will display: (e.G. [yes]) if the de-regis...

  • Page 28

    Programming the handset page 3-7 note: 1. The base doesn’t need to enter the de-registration mode. And, the system must be in idle mode. 2. Only one handset can de-register to the base at a time. 3. The handset can register to the other base without de- registration to the original base. But the ori...

  • Page 29

    Emerald ice cordless handset quick start guide page 3-8 4. Toggle the [f1/f2] keys to change the item. 5. Press [f3] to confirm. The lcd will display: (ring mode only shown) if user selects [ring and vibrator] mode, the lcd display will show both ring and vibrator icons..

  • Page 30

    Programming the handset page 3-9 note: 1. The unit will generate the reference ring or/and vibration for the user to refer the ring type. 2. The mark [_ã] means that user enables this function. 3. There are some icons (( )) on the row-1. It will indicate user’s setting. Ring and/or vibration. 4. Pre...

  • Page 31

    Emerald ice cordless handset quick start guide page 3-10 3. Press [f3] to enter the change mode. The lcd will dis- play: 4. Toggle the [f1/f2] key to change the item. Or press [f3] to confirm. The lcd will display: (handsfree mode shown): release call programming release call programming allows the ...

  • Page 32

    Programming the handset page 3-11 2. Press [f1] 5 more times and the lcd will display: 3. Press [f3] to enter the change mode. The lcd will dis- play: 4. Toggle the [f1/f2] keys to change the item. 5. Press [f3] to confirm, the lcd will display: (by spkr key shown):.

  • Page 33

    Emerald ice cordless handset quick start guide page 3-12 reset handset programming reset programming will reset the handset unit back to the default status. 1. Press and hold the [f1] key for 1 second to enter the pro- gramming mode. 2. Press [f1] 6 more times. The lcd will display: 3. Press [f3] to...

  • Page 34

    Programming the handset page 3-13 after 3 seconds, the handset comes back to the default status and the lcd will display the following message for 5 – 10 sec- onds. If the handset never register to the base or has been reset, the lcd will also display:.

  • Page 35: Extra Functions

    Extra functions.

  • Page 36: Extra Functions

    Extra functions page 4-1 the emerald ice cordless system provides more information for rf link status and battery power status. The user can eas- ily find the current handset status about the rf link and batter status. Note: 1. All new information about rf and battery status will be displayed on the...

  • Page 37

    Emerald ice corless handset quick start guide page 4-2 out of range status if the handset is in talk mode and the user is an extended dis- tance away from the base unit, the handset will display [out of range] and generate the warning beep per 5 seconds: if the user does not return to close proximit...

  • Page 38

    Extra functions page 4-3 ring and vibrator status if a user sets [ring mode] only, a [ring] icon will appear on the lcd. If a user selects [vibrator mode] only, (( )) will appear on the lcd. If a user selects [ring and vibrator mode], both icons will be displayed on the lcd..

  • Page 39

    Emerald ice corless handset quick start guide page 4-4 sleeping mode status for power saving purposes, the handset will enter sleeping mode automatically when there is no special event in the sys- tem. Row-3 of the lcd will display a handset extension number for the user’s reference. Row-2 will be b...

  • Page 40

    Extra functions page 4-5 when handset is in the key locked mode and long keypress [flash], the lcd will display a 3-second display as follows: if a user presses the key [f3] within 3 seconds, the handset will be in key unlock mode. Note: the [flash] key will be changed to [transfer] key in some mode...

  • Page 41

    Emerald ice corless handset quick start guide page 4-6 no link to ksu status when power is on for approximately 1 minute, and the base unit still cannot link with the ksu, the handset will display the following:.

  • Page 42

    Extra functions page 4-7.

  • Page 43: System Limitations

    System limitations.

  • Page 44: Extra Functions

    System limitations page 5-1 registration and de-registration all registration and de-registration functions can operate during the 1 st one minute only, therefore, the user must remove the base power and re-power on the base unit to register or de-reg- ister the system. Off hook voice announcement (...

  • Page 46

    Visit us at our website http://www.Tadiran-us.Com email: icetechsupport@tadiran-us.Com usa headquarters tadiran telecom, inc. 4 tri harbor court port washington, ny 11050 tel. +1-516-632-7200, fax. +1-516-632-7210 e merald ic e c or d les s ha nds et qui ck s ta r t gui de.