1. DL manuals
  2. Taian Puhui
  3. Soldering Gun
  4. T862++
  5. User Manual

Taian Puhui T862++ User Manual

Manual is about: IR BGA Rework Station

Summary of T862++

  • Page 1

    Ir bga rework station t862++ user manual taian puhui electric technology co. ,ltd www.Tech168.Cn.

  • Page 2

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 1 content 1. Features…………………………………………..………….2 2. Technical parameters……………………………………………..3 3. List of content…………..……………………………..……..……3 4. Description of the main parts………………..…………..……….4 (1) main body……………………………………………..….………4 (2) front...

  • Page 3

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 2 1、features 1）use of infrared welding technology which is developed independently. 2）use of an infrared heat lamp. Heat is easy to pierce and distribute evenly, which overcome disadvantage (burn out elements) of traditional welding ma...

  • Page 4

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 3 technical parameter working voltage ac220v/50hz ac110v/60hz output power 800w infra-red lamp body temperature adjustable 100℃-350℃ preheating dish temperature adjustable 60℃-200℃ components description quantity illustration t-862++ c...

  • Page 5

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 4 t-862++ illustrated explaining (1)the whole machine (2)front panel cell guide the end covering focus holder control knob 钮 chassis (working bench ) preheat plate lens for infrared lamp front panel eye protection (ir filter) fan prote...

  • Page 6

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 5 rear panel the screen displayed the temperature of the preheat plate the screen displayed the peak temperature of the ir lamp preheat switch infrared lamp switch temperature set-point entry buttons connecter for universal power line ...

  • Page 7

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 6 (3)infrared lamp (focus holder and others) focus holder control knob fasten nut for focus holder fasten nut for steady ring focus holder focus holder ir lamp cooling fan steady ring cell guide.

  • Page 8

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 7 installation 1. Install the guide rod. Loosen the pinch nut of focusing support; put the guide rod in according to the direction of arrow icon pointing. Note: the infrared head, body mounting and focus assembly will be installed in t...

  • Page 9

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 8 □ pick up focusing support; make the guide rod aim at the corresponding nut on the base, then rotate the guide rod. □ fasten the focusing support by rotating pinch nut of it. □ rip off the protective film of the filter. . 5. Connecti...

  • Page 10: T-862++    Operation

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 9 t-862++ operation 1. Starting 1）inspect the infrared lamp body, temperature sensor and power line and see if they are in good connection. 2）turn on the power switch, then use self-checking first (the previous setting value demonstrat...

  • Page 11

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 10 (1)when the area of the chips is below 15mm*15mm, please choose the ir-lamp temperature about 160-240℃, and choose the lens which d=28mm to avoid destroying other places, usually it will take you about 20-40seconds. (2)when the area...

  • Page 12

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 11 2. Unsoldering operation adjust temperature, make the center of the infrared lamp aim at the unsoldered chip. Once the tin is sufficiently melted, remove the chip. 3. Soldering operation ①clean up the welding plate with a brush..

  • Page 13

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 12 ② put the tin ball and spread soldering flux (not too thick, only a thin layer of it) on the soldering plate. ③ put the chip in the accurate place after the solvent volatilizes out of soldering flux, heat the tin ball until it melts...

  • Page 14

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 13 4. Using the lead-free soldering iron switch on the power, set the temperature that you need, turn on the it can be used separately, but be sure it must be connect with the chassis. If the component is too small, you needn’t use the...

  • Page 15

    Irda bga rework station t862++ user manual http://www.Tech168.Cn 14 regularly. 4. Pull out the power plug if you don’t use it for a long term. 5. Be careful of operating under high temperature conditions. Warranty statement reminder: these machines are very heavy, between 8 to 15 kilograms and are n...