Talento 472 User Manual

Summary of 472

  • Page 1

    1. Contents 2 1. Contents page 2. Assembly, putting into operation, connection 3 3. Control elements 4 4. Display 4 5. Factory setting 5 6. Changing settings 6 6.1 time and day of the week 6 6.2 calendar month and day 7 6.2.1 au = automatic changeover 7 6.2.2 cha = weekday-related time change 8 - 9 ...

  • Page 2

    2. Assembly, putting into operation, connection 3 gb 3.1 assembly fit the time switch • on a din rail • optional wall surface-mounting surface-mounting set for 2 and 3 module spacings article no. 03.53.0083.2 3.2 putting into operation the time and date are set at the factory. The time switch is in ...

  • Page 3

    3. Control elements 4 start program input set time, end program input select day(s) of the week delete switching time set hours, day, year hand switch enter pulse/ cycle reset set minutes, month, year summer time/winter time switchover 4. Display date summer time display am/pm display dcf 77 recepti...

  • Page 4

    Gb 5 5. Factory setting the selections correspond to central european time. The time switch offers 3 operating modes. The date and time, and also the operating mode au are set. Operating modes: • au automatic summer time controller switchover see 6.2.1 the switchover occurs on the dates defined by t...

  • Page 5

    6 6. Changing settings press the key once. Set the time: with the h key – hours with the m key – minutes note: if the operating mode no = no change - see 6.2.3 was selected, the day of the week must now be set. With the day 1 - monday key select: 2 - tuesday 3 - wednesday : 7 - sunday press the key ...

  • Page 6

    Gb 7 6.2 calendar month and day – select the operating mode 6.2.1 au = automatic changeover press the key once press the + 1h key once, au appears press the prog key once set the current year: with the m key or the h key confirm with the prog key set the current month and day: with the m key – calen...

  • Page 7

    8 6.2.2 cha = weekday – related time change press the key once press the + 1h key as often as necessary until cha appears press the prog key once set the current year: with the m key or the h key confirm with the prog key set the current month and day: with the m key – calendar month with the h key ...

  • Page 8

    Gb 9 confirm with the prog key the start of summer time is displayed. Set the individual summer time start: with the m key – month with the h key – day confirm with the prog key set individual summer time end: with the m key – month with the h key – day press the key once. The input is ended..

  • Page 9

    6.2.3 no = no changeover press the key once press the + 1h as often as necessary until no appears. The time switch operators without a date! Press the key once. The input is ended. Note: select day of the week see 6.1 10

  • Page 10

    Gb select free memory location: press the prog key as often as necessary until – –:-– – appears. Set the switching times: with the m key – minutes with the h key – hours for weekday adjustment, see: block formation of weekdays, point 8 you determine the switching times and the switching state for th...

  • Page 11

    12 select free memory location: press prog as often as necessary until – –:– – appears press the day key once all 7 days of the week are active activating/deactivating days of the week: press the day key once. There is a cursor under the number1 (2...7) activate/deactivate the day of week with the d...

  • Page 12

    Gb 13 press the key once. The weekday selection is ended. Note: enter the switching times and the switching state = on = off for the relevant switching state (channel). For standard switching commands, see 7 for impulse switching commands, see 9 for cycle switching commands, see 10 note: after the p...

  • Page 13

    14 9. Impulse switching commands if a load is switched on and off with a high switching frequency in the seconds range, it must be ensured that effects on the quality of lighting units (flickering) and interference with radio and tv reception are avoided. You determine the times for pulse switching ...

  • Page 14

    Gb 15 selecting the switching output: with the key ch1 and/or ch2 confirm with the prog key. Preselection for: – seconds – minutes with the m key set the on switching duration: with the key 01...99 confirm with the prog key. The input is ended. A free memory location is displayed for further setting...

  • Page 15

    16 you determine the times for cycle switching commands symbols: = on switching duration (1...99 sec. Or 1...99 min.) = cycle duration (1...99 sec. Or 1...99 min.) the preselection for seconds or minutes is explained at the given time. A cycle switching command consists of: • start time • on switchi...

  • Page 16

    Gb 17 select free memory location: press the prog key as often as necessary until – –:– – appears. Set the start time: set the day(s) of the week, see 8 with the m key – minutes with the h key – hours preselection for cycle = mark the cycle switching command with the key (press 2x) select the switch...

  • Page 17

    18 preselection for: - seconds - minutes with the m key set the on switching duration: with the key 01...99 confirm with the prog key a switching off time is displayed here with 00:00 for all 7 days of the week. You can change these individually or delete them with clear. The input is ended. A free ...

  • Page 18

    Gb 19 read press the prog key step by step each individual content is displayed until the end of the program. Then: • one free memory location – –:– – • one digit (free memory locations) (ex. Fr 10) change press the prog key step by step as far as the switching command/ contents which you want to ch...

  • Page 19

    20 delete - all switching commands press the prog key as often as necessary until frxx appears press the clear key once. Cl is in the display press the clear key and hold it down. All memory locations are deleted! The display shows the number of the max. Memory locations. Reset press the reset key o...

  • Page 20

    Gb 21 you change – manually – the current switching state. However, the individually set switching program is preserved. 1 for channel 1 2 for channel 2 12. Hand switch = automatic = off = on the switching state corresponds to the entered program. = manual mode = on = off you change – m a n u a l l ...

  • Page 21

    22 14. Technical data 1 channel weekly program 2 channel weekly program 45 x 36 x 60 45 x 36 170 see unit imprint see unit imprint 16 a/250 v ac 2,5 a/250 v ac 1000 w potential-free 1 or 2 changeover contacts ii ip 20 ± 2.5 s/day at +20° c – lithium 3 years from factory 1 minute every minute 30/40 y...