Taylor 7322 Instruction Manual

Thank you for purchasing a Taylor® Lithium Electronic scale. All of our 

precision instruments for weight measurement are engineered and 

designed to meet the highest quality standards …to assure you years of 

uncompromising accuracy and consistently dependable, convenient 

performance. 

Please read this instruction manual carefully before use. Keep these 

instructions handy for future reference.

1. Clean exposed parts with a soft, slightly damp cloth. To remove 

stains, use a mild soap. Never use detergents, excess water, treated 

cloths, harsh cleaning agents, or sprays. Do not attempt to lubricate 

or open scale casing as this will void your warranty.

2. Although your scale is designed to be maintenance-free, it contains 

sensitive electronic parts. Avoid rough treatment. Do not drop, kick, 

or jump on it. Treat it with care to ensure the best performance.

3. This scale is designed to read weights between 25 and 330 lbs and 

12 and 150 kgs. To prevent damage, do not place more than 330 lbs 

or 150 kgs on it.

4. Do not store scale where you store cleaning chemicals. The vapors 

from some household products may affect the electronic components 

of your scale. Do not store scale on its side.

5. This scale is an extremely sensitive weighing device. In order to 

prevent run down of the battery, do not store anything on the scale.

6. Do not dispose of batteries in fire. Batteries may explode or leak. 

Remove the battery if the scale will not be used for a long period of 

time.

1. There is a red strip under the Lithium battery cover to prevent 

battery drain in shipping. Please remove the strip before continuing 

with these instructions. Also, some models have a static cling label 

on the lens to prevent scratching. Please remove before use.

2. Your scale has been set at the factory to read weight in pounds. You 

may select kilograms by moving the slide switch on the bottom of the 

scale. 

3. Place scale on flat, hard surface. Carpeted or uneven floors may 

affect accuracy.

4. Step on the scale (disregarding the reading) and step off. This 

process insures the scale is set and is now ready for use. Do this 

whenever the scale is moved. At all other times step straight 

onto the scale.

5. Step onto the scale platform and remain still. The display will show 

“

0.0 

”, then count up to your weight.  The display will flash twice 

when the weight is locked. Your weight is now displayed. 

6. If you step off of the scale, the display will turn off automatically 

within 5 seconds. If you continue to stand on the scale, your weight 

will be displayed for 30 seconds and then the scale will turn off 

automatically.

Your Taylor® scale has a lithium battery installed to provide extra long 

energy life for your scale. Under heavy usage (Health Club, Wellness 

Clinic, etc.) the battery may eventually need to be replaced.

Maintaining proper weight is essential to healthy living. Obesity 

has been linked to a higher risk of heart disease, diabetes and 

some forms of cancer. The Body Mass Index (BMI) is the most 

widely accepted measurement of weight according to health 

professionals.

Use the chart below to determine your own BMI by matching 

your height in the left hand column with your weight in the 

center. Anyone, male or female, with a BMI of 25 to 29 is 

considered over weight and a body mass index of 30 is 

considered obese. Remember to eat right and exercise.

In Case of Difficulty...

1.  Place  your  feet  in  the  same  position  every  time  you  weigh 

yourself. Stand still during measurement.

2. Weigh yourself without clothing whenever possible. Clothes can 

vary in weight.

3. Move the scale to a location where it won't be bumped. If your 

scale  is  bumped  while  being  activated  or  while  in  use,  an 

inaccurate reading may occur.

4. For the most consistent readings, weigh yourself at the same 

time of day. Allow for weight fluctuations due to food or drink in 

your system.

5. The maximum capacity of this scale is 330 lbs / 150 kgs. Should 

“

Err

 ” appear on the display during a weighing, this indicates that 

the maximum weighing capacity of the scale has been exceeded. 

Remove the weight immediately; otherwise, permanent damage 

may occur.

CP7322  12.10

Lithium

Electronic Scale 

Battery Replacement

Reaching Target Weight

Low Battery

Trouble Shooting

General Operation

Battery Information

7322

Leading the Way in Accuracy®

1. Use one 3 volt CR2032 lithium battery (as installed).

2. Open the battery compartment on the bottom of the scale by 

pushing the tab in the direction of the “open” arrow and lifting up 

the cover.

3. Remove the old battery from the compartment.

4. Place the new battery with the “+” 

sign up into the battery compartment.

5. Push gently down on the compartment 

cover until it clicks shut.

Your Taylor® scale is equipped with a low 

battery indicator. It will display “ 

LO 

” or 

readings will grow dim or become irregular 

if the battery needs replacement.

Five (5) Year Limited Warranty

There are no express warranties except as listed above. This warranty gives you specific 

legal rights, and you may have other rights which vary from state to state.

For additional product information, or warranty information outside the USA, please 

contact us through www.taylorusa.com.

©2010 Taylor Precision Products and its affiliated companies, all rights reserved. Taylor® 

and Leading the Way in Accuracy® are a registered trademarks of Taylor Precision 

Products and its affiliated companies. All rights reserved.

Made to our exact specifications in China.

Not legal for trade.

www.taylorusa.com

This scale is warranted against defects in materials of workmanship five (5) 

years  of the original purchaser from date of retail purchase (excluding 

batteries). It does not cover damages or wear resulting from accident, misuse, 

abuse, commercial use, or unauthorized adjustment and/or repair. Do not 

return to retailer. Should this scale require service (or replacement at our 

option) while under warranty, please pack the item in the original packaging 

and return it prepaid, along with store receipt showing date of purchase and a 

note explaining reason for return to:

Taylor Precision Products

2220 Entrada Del Sol, Suite A

Las Cruces, New Mexico 88001    USA