Taylor TE10R Instruction Manual

HOLD

NET

g

g

lb

k

oz

1. Remove the scale from its box, along with its platform 

assembly and the adaptor.

2. Install the platform assembly onto the scale by matching the 

plastic posts of the platform assembly with the mating holes 

on the top of the scale (no special orientation is required).

POWER

To turn the scale on, press the button marked “ON/OFF”. The display 

will first show “88888” followed by “”. To turn the scale off, push 

the “ON/OFF” button. The scale will remember the unit mode last 

shown, and this unit will display when the scale is turned on again.

UNIT CONVERSION

Press the Unit Conversion Button to switch from fractional ounces to 

decimal ounces to grams to ounces. When the scale is turned off, it 

will remember the unit mode last shown and will turn-on in that mode. 

WEIGHING

When the display shows “0”, the scale is ready to weigh an object. If 

the object exceeds the capacity of the scale by more than 10%, the 

display will show “Err” (for error). Until the overload condition is 

reached, additional objects may be placed on the platform. The 

display will show the sum of the weights of all the objects. When one 

of multiple objects is removed from the platform, the weight of the 

remaining objects will display.

TARE OPERATION

To tare (zero out) a load on the platform (example: the weight of a 

container), press the “TARE” button. The display will show the value 

“0”. 

During the “TARE” mode, a new item can be added to the platform. 

The display will show the sum of the weights of the added items. 

Another item may be added, if desired. The display will show the sum 

of all additional item weights above and beyond the tared out load.

TARE CAPABILITY

A load of up to 50% of the scale's capacity can be tared out, while still 

allowing the weighing of an additional object, up to the full capacity 

of the scale. 

Tare capability example: On a 10 pound scale (TE10), a load of 5 lbs 

(50%) can be tared out. Once tared out, an added weight of 11 lbs (full 

capacity plus 10%) can still be weighed without causing an overload 

condition.

If a load that exceeds 50% of the scale's capacity is tared out, the 

additional weight that can be measured will be reduced accordingly. 

HOLD OPERATION

The “HOLD” function may be used to lock the weight on the display for 

ten (10) seconds, even after the load is removed from the platform. 

To use the hold function, press the “HOLD” button. A small triangle will 

appear in the upper left corner of the display next to the word “hold”, 

indicating the hold function is turned on. This triangle and the “hold” 

function will remain in place until the “HOLD” button is pressed again. 

This pressing of the “HOLD” button a second time will cancel the “hold” 

function, and the triangle will disappear from the display. While the 

scale is in “HOLD” mode:

Place a load on the platform. When the weight is locked in, the triangle 

will begin to flash. When the load is removed from the platform, the 

display will continue to show the weight for ten seconds. After the ten 

second period is up, the triangle will stop flashing, and the display will 

show “0”. If the load is not removed from the platform, the triangle will 

continue to flash. The ten second “hold” period will begin once the 

load is finally removed from the platform.

During the ten (10) second period, the load can be tared out, causing 

the display to show “0”. And additional load will be displayed and held 

for another ten second period, etc.

If the “HOLD” button is pressed again, the scale will revert to its normal 

operating mode.

When the scale turns off, the hold function is cancelled. When the scale 

is turned on again, it will be in normal operating mode.

The Digital Portion Control Scale operates with a rechargeable 

battery (included). To install and charge the battery:

1. Remove the battery compartment door on the bottom of the 

scale.

2. Plug the male connector of the rechargeable battery onto the 

female connector, which is located in the battery compartment.

3. Place the rechargeable battery into the battery box.

4. Replace the battery door.

5. To charge the battery, insert the connector plug of the adaptor 

into the jack at the back of the scale. Plug the other end of the 

adaptor into the proper electrical outlet. A red LED on the side of 

the scale will light up, indicating the battery is charging. When the 

LED light changes to green, the battery is completely charged.

6. Allow at least 12 hours for the scale to charge completely. The 

scale will then operate continuously for approximately 14 hours.

7. The battery life cycle is approximately 500 recharges. If the scale 

does not function properly after at least 12 hours of charging, the 

battery may need to be replaced. The scale will still operate on 

adaptor power if the battery is not charged.

8. To purchase a new rechargeable battery (model TERBAT), please 

contact customer service at 1-800-225-4834.

9. There is also an AC adaptor included with this scale and can be 

used in place of the Rechargeable Battery.

Thank you for purchasing a Taylor® Digital Portion Control Scale. Your 

scale is an example of superior design and craftsmanship. In order to 

optimize its function, be sure the read this instruction manual carefully 

before use. Keep instructions handy for future reference.

Main Features

Main Features (continued)

Before You Begin

General Operation

General Operation (continued)

Battery Installation

Description of Parts

Pound

Display

Kilogram

Display

Grams

Display

LCD

Display

Scale Stable

Display

Hold

Display

LED

Indicator

Unit Conversion

Button

On/Off

Button

Ounces

Display

Hold 

Button

Tare / Light

Button

Instruction Manual

Digital Portion 

Control Scale

®

Leading the Way in Accuracy

 TE10R

Specifications

One Year Limited Warranty

This product is warranted against defects in materials or 

workmanship for one (1) year from date of original purchase for the 

original purchaser. It does not cover damages or wear resulting 

from accident, misuse, abuse, or unauthorized adjustment and/or 

repair. Should this product require service (or replacement at our 

option) while under warranty, please pack the item carefully and 

return it prepaid, along with receipt showing date of purchase and 

a note explaining reason for return to:

Caution: Changes or modifications not expressly approved by 

the party responsible for compliance could void the user's 

authority to operate the equipment.

Note: This device complies with part 15 of the FCC Rules. 

Operation is subject to the following two conditions: (1) this 

device may not cause harmful interference, and (2) this device 

must accept any interference received, including interference 

that may cause undesired operation. This equipment has been 

tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC rules. These limits are 

designed to provide reasonable protection against harmful 

interference in a residential installation.  This equipment 

generates, uses and can radiate radio frequency energy and, if 

not installed and used in accordance with the instructions, may 

cause harmful interference to radio communications.  However, 

there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more 

of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for 

help.

NOTE: please recycle or dispose of batteries per local regulations.

WARNING: Batteries may pose a choking hazard. As with all small items, 

do not let children handle batteries. If swallowed, seek medical 

attention immediately.

PRECAUTION: Do not dispose of batteries in fire.  Batteries may explode 

or leak.  Remove the batteries if the scale will not be used for a long 

period of time.

TE10R - 11.13WC

Platform: 8-1/16” x 5”, Stainless steel (TE10ROS 10” x 6.75”)

Power:  (1) 9 Volt battery (not included) or AC adaptor 

(included)

Dimensions: 8-1/16” x 7-3/4” x 2-1/4”

Weight: 2 lbs, 3 oz (TE10ROS 3lbs, 3oz)

Capacity: 10 lb x 1/8 oz

                  10 lb x 0.05 oz

                  160 oz x 0.05 oz

                  5000 g x 1 g

Resolution: 0 to 10 lbs by 1/8 oz increments

                   0 to 10 lbs by 0.05 oz increments

                   0 to 5000 g by 1 g increments

Accuracy: oz mode, +/-10 division

                   g mode, +/-10 division

This scale is engineered to give you years of satisfactory 

service if you handle it carefully. Here are a few precautions:

1. Always read instructions thoroughly to ensure that you have 

the full benefit of all the unit's features.

2. DO NOT immerse unit in water, as doing so will cause 

damage to internal components and void the warranty. If 

you spill liquid on it, dry it immediately with a soft, lint-free 

cloth.

3. DO NOT clean the unit with an abrasive or corrosive 

material. This may scratch the plastic parts and corrode the 

electronic circuits.

4. DO NOT subject the units to excessive force, shock, dust, 

temperature or humidity. This may result in malfunction, 

shorter electronic life span, damaged battery and distorted 

parts.

5. DO NOT tamper with the unit's internal components. Doing 

so will invalidate the warranty on the units and may cause 

damage. The unit contains no user-serviceable parts.

6. This scale is an extremely sensitive weighing device. To avoid 

damage to the unit or the battery, do not store anything on 

the scale.

7. Remove the battery if the scale will not be used for a long 

period of time.

8. DO NOT dispose of batteries in fire. Disposing of this product 

in fire could cause batteries to explode or leak. Remove the 

battery if the unit will not be used for a long period of time.

Precautions

TThe scale will automatically shut off after 3 minutes of nonuse 

to conserve the battery. The auto-shut off feature can be 

disabled to allow the scale to operate continuously. To disable 

the auto-shut off feature:

1. While the scale is off, press and hold the “UNIT CONVERSION” 

button.

2. While continuing to hold down the “UNIT CONVERSION” 

button, also press and hold down the “ON/OFF” button.

3. The display will show “88888”, then “A-oF” The auto-off 

feature is now disabled. Release the buttons.

4. To enable the auto-off feature again, repeat steps 1 and 2. 

“A-on” will appear. The auto-off feature is now functional.

Taylor Precision Products, Inc.

2220 Entrada Del Sol,  Suite A

Las Cruces, New Mexico 88001    USA

Customer Service Phone: 1-800-225-4834

Customer Service Fax: 1-575-526-4347

www.taylorusa.com

There are no expressed warranties except as listed above. This warranty 

gives you specific legal rights, and you may also have other rights which 

vary from state to state.

For additional product information, or warranty information in Canada 

or elsewhere outside the USA, please contact us through 

www.taylorusa.com.

©2013 Taylor Precision Products, Inc. and its affiliated companies, all 

rights reserved. Taylor® and Leading the Way in Accuracy® are 

registered trademarks of Taylor Precision Products, Inc. and its affiliated 

companies. All rights reserved.

Made to our exact specifications in China.

NOT LEGAL FOR TRADE

Auto Shut-Off Feature

• LCD Screen

   1.0” digits display weight.

• Hold Button

   When pressed, the weight will display for ten seconds, even 

after the weight is removed.

• Unit Conversion Button

   When pressed, converts the weight display from fractional oz 

to decimal oz to grams.

• Tare Button

   When pressed, the scale reading returns to zero. Additionally, 

it can be used to offset the weight of a container or other 

object up to 50% of the scale's capacity.

• ON/OFF Button

   When pressed, turns the scale “ON” or “OFF”.

• Backlit Display

   Will illuminate when weight is added or removed from 

platform. Press and Hold “ TARE ” to turn On/Off backlight 

function.

• Moisture Resistant

   Components are sealed for resistance to moisture.

• Auto Shut Off

   Scale powers off after 3 minutes of nonuse.

• Low Battery Indicator

   Appears on LCD screen when battery is low.

• Overload Signal

   Warning appears when weight is at 10% above the scale's 

rated capacity, even after tare up to 50% of capacity (in 

pound mode).