Summary of 20B
Page 2
Table of contents safety precautions 3 machine components 4 machine set up 5 machine installation 5-6 machine operation 6 tank draining 7 battery charging 7-8 preventative maintenance 8-9 machine storage 9 basic troubleshooting 10 parts breakdowns and lists 11-27 wiring diagram 28 warranty policy 29...
Page 3
Safety precautions this machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only with recommended accessories. All operators shall read, understand and exercise the following safety precautions: 1) do not operate machi...
Page 4: Machine Components
Machine components 1. Vacuum on/off switch 2. Brush on/off switch 3. Battery level meter 4. Solution on/off switch 5. Solution control knob 6. Recovery tank drain hose 7. Squeegee assembly 8. Brush lift foot pedal 9. Solution tank level sight tube 10. Console adjustment levers 11. Rear solution fill...
Page 5
Machine set up & installation uncrating machine be sure and check packing carton for any damage. Immediately report any damage to carrier. Check contents of package to ensure that the following items are included: machine, batteries (x2), squeegee assembly, battery charger, and pad driver. Battery c...
Page 6
Filling the solution tank 1. The panther 20b can be filled in two different locations: a. Front fill area for use with a hose or a bucket. B. Rear fill area for use with a hose only. 2. Determine which fill area you would like to use to fill the machine with water. 3. Fill solution tank with up to 1...
Page 7
Determine what caused the breaker to trip, and allow the motor to cool down before you can reset the breaker. The breaker is located on the back panel of the control housing. Tank draining 1. Turn the power off on the machine 2. With the squeegee and brush head in their “up” position, transport mach...
Page 8
6. Plug charger into red charger receptacle which comes off the battery pack. 7. Flip up the recovery tank “kick stand” and gently lay the recovery tank down until it rests on the stand. 8. The charger will automatically begin to charger the batteries, and it will automatically shut down once the ba...
Page 9
Battery maintenance : for the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition. : batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times. : whenever se...
Page 10
Problem cause solution no power bad batteries replace batteries batteries need to be charged charge batteries (see battery charging) loose battery cable tighten loose cable(s) batteries not connected properly follow battery installation instructions brush motor does not run bad brush switch contact ...
Page 11
11.
Page 12
Dia part description no solution tank assembly no number description req'd 1 vf81405tr grip, handle 1 2 va13477 screw, self-tapping, st, m4 x 16 3 3 vv13664 washer, plain, m4 x m12 x 1 1 4 vf81507 strap, plug, rear fill 1 5 vv13604 screw, m8 x 20 6 6 vf13519 washer, lock, m8 6 7 vf81509 plug, expans...
Page 13
Dia part description no solution tank assembly dia no part number description no req'd 39 vf82076 plate 1 40 vf82072 spacer, battery 1 vf81724 cap, battery, black 2 vf81724r cap, battery, red 2 42 vf82403 cable battery 1 41 42 vf82403 cable, battery 1 43 vf14234 screw, m8 x 16 2 44 vf13513 nut, m8 2...
Page 14
14.
Page 15
Recovery tank assembly dia no part number description no req'd 1 vf82010 clear cover, recovery tank 1 2 vf82083 decal, battery warning 1 3 vf82009 elbow adaptor, float 1 4 vv13607 washer, lock, m6 13 5 vf13533 washer, plain, m6 x m16 x 2 7 6 vf14233 screw, m6 x 20 4 7 vf81504 float 1 8 vf82002 recov...
Page 16
16.
Page 17
Dia no part number description no req'd brush lift / wheel axle assembly no number description req'd 1 vf14075 bearing, #6004 4 2 vf82005 wheel, 8" 2 3 vf82101 bushing 2 4 vf82210 shaft 1 5 vf13535 washer, plain, m8 x m20 x 2 10 6 vf13519 washer, lock, m8 12 va13491 screw m8 x 2 6 7 va13491 screw, m...
Page 18
18.
Page 19
Brush / pad drive assembly dia no part number description no req'd 1 zd45000 brush motor, 24vdc, .75hp 1 2 zd45407 key, 6.35 x 25 1 3 vf13545 screw, self-tapping,st, m5 x 10 4 4 vv13601 washer, lock, m5 4 5 vf83131 clamp, brush plate 1 6 vf83132 spring 1 7 vf83130 plate, drive 1 8 vf82058 washer 1 9...
Page 20
20
Page 21
Dia part description no solution control assembly no number description req'd 1 vf14245 screw, m5 x 6 2 2 vf82036 shaft 1 3 vv13650 screw, m4 x 10 1 4 vf13532 washer, plain, m5 4 5 vv13601 washer, lock, m5 5 6 vf14230 screw m5 x 15 2 6 vf14230 screw, m5 x 15 2 7 vf13536 washer, plain, m9.8 x m16 x 1...
Page 22
22.
Page 23
Brush skirt assembly dia no part number description no req'd 1 vf82014 bumper 2 2 va13491 screw, m8 x 25 5 3 vf13519 washer, lock, m8 7 4 7 4 vf13535 washer, plain, m8 x m20 x 2 7 5 vf13514a washer, plain,m8 x m16.5 x 1 4 6 vf82013 wheel, 3" 4 7 vf82055 bushing 4 8 vf14236 screw, m8 x 40 2 9 14 9 va...
Page 24
24.
Page 25
Dia no part number no req'd 1 vf81713 2 2 vf14122 2 3 vf14121 2 4 vf13502 10 5 gt13032 2 vf81781 3 vf81781-x 3 7 vf81726a 2 8 vf81734 2 9 vf83149 1 10 vf82108 1 11 vf14078 6 12 va50477 6 13 vf81718 1 14 vf13495 4 15 vf82313 1 16 vf81719 6 17 vf82102a 1 18 vf82103a 1 19 vf81721 3 20 vf14200 12 21 vf8...
Page 26
26.
Page 27
Squeegee assembly dia no part number description no req'd 1 vf14247 screw, m12 x 25 2 2 vf13538 washer, plain, m12 x m26 x 2 2 3 vf82016a bushing 2 4 vf82130 mount, pivot 1 5 vf13541 washer lock m12 2 5 vf13541 washer, lock, m12 2 6 vf82049 cable, squeegee lift 1 7 vf82112 bushing 1 8 vf81203a hose ...
Page 28
28.
Page 29: Warranty Policy
Warranty policy the warranty terms outlined below are in lieu of any other warranties, either stated or implied, including any implied warranty of merchantability, fitness for a particular purpose or otherwise. Under no circumstances will seller be liable for any loss, damage, expense or consequenti...