Valtra MEGA MEZZO HI-TEC Workshop Manual

Summary of MEGA MEZZO HI-TEC

  • Page 1

    Valtra – valmet mega mezzo hi-tec workshop manual.

  • Page 2

    Service manual tractors power transmission brake system steering sys- tem and front axle frame and wheels tools cab and shields hydraulics valtra inc. 44200 suolahti, finland groups 10---100 general engine electrical system 40 50 60 70 80 100 90 10 20 30

  • Page 3

    696 model code page 42 gearbox 22 420 6000--8750 15. 5. 1993 picture 23. Lubricating system of power transmission on tractors which have 3---step quick---shift gear (delta powers- hift), 660071 --- . 1. Servo valve block, 660071 --- 2. Lubricating oil supply pipe 3. Distribution piece inside the rev...

  • Page 4

    697 w orki ng ord er in th e ta ble be lo w is sh ow n th e w orkin g ord ers fo rc erta in ge arb ox rep ai rw ork. R eco nd itio ni ng selecto rf orks, see co de 421. R em ov in g, reco nd itio nin g an d fittin g ge arb ox ,see co de 423. Drain trans - m issi on oi l re mo ve sid e cov er ra is e...

  • Page 5

    699 model code page 42. Gearbox 1. 1. 1995 6000--8750 420 4a 1. Screw the nut fully home 2. Unscrew it then 1,5 turns celarance= 0 0,025...0,075 mm 1,7...2,3 nm 0,175...0,325 mm 0,025...0,075 mm 0,025...0,075 mm +0,6...1,7 nm (z7/40, z8/42) +0,8...2,2 nm (z9/38) +1,0...2,8 nm (z11/37) please do not ...

  • Page 6

    701 model code page 42. Gearbox 1. 6. 1999 6250--8950 420 4b.

  • Page 7

    Sliding coupling in middle pos. Synchronizing cone cone 703 model code page 42. Gearbox 8. 11. 1990 6000--8750 421 1 selector forks (op. No. 421) 1. Adjusting selector forks note! If the gear change mechanism does not function properly (e.G. If selected gear does not stay in the engaged position), t...

  • Page 8

    704 model code page 42 gearbox 15. 5. 1996 2 421 6000--8750 1. 1. 1995 8. Take the hold of the rail and move it. It must move loosely. 9. Then push the rail (together with the fork) to the front posi- tion. Move the rail again. It must move loosely. 10. Adjust if necessary and finally tighten the ad...

  • Page 9

    705 model code page 42. Gearbox 6000--8750 423 1 1. 8. 1998 8. 11. 1990 reconditioning gearbox (op. No. 423) 1. Removing gearbox note! The gearbox is easiest to remove if it is possible to remove the cabin (removing and fitting cabin, see op. 811 1a). In the instruction below the cabin, however is i...

  • Page 10

    706 model code page 42. Gearbox 1. 8. 1998 6000--8750 423 2 8. 11. 1990 11. Disconnect the control valve solenoid wires on the gear- box side cover. Disconnect oil hoses from the pressure filter. Note! It is easier to disconnect and connect the hoses if the pressure filter is removed. Pressure filte...

  • Page 11: Buy

    Buy now then instant download the complete manual thank you very much!.