- DL manuals
- W & H
- Power Tool
- 154
- Operator's Manual
W & H 154 Operator's Manual
Summary of 154
Page 1
Model 154 operator’s manual manual # om-98 williams & hussey machine co., inc. Www.Williamsnhussey.Com 1-800-258-1380, fax 603-732-4048 customer service is available monday-friday, 8:30 am- 4:30 pm est 11 th revision july 2010
Page 2: Safety Rules
Specifications accessories motor 2hp guide system gs-2 rpm 6900 elliptical jig ej-92 feed rate 15 fpm retro kit vf-104-k max profile depth ¾” retro kit vf-106-k max profile width 6 ¾” 11fpm kit 54-310-k planing width 7” 20fpm kit 54-311-k min stock length 9” r. Panel kit 54-312-k min stock thickness...
Page 3
Disconnect the power before servicing or changing knives. Wear footwear that does not slip. This will help you keep proper footing and balance. Always stand beside the machine, never in the way of the in-feed or out-feed areas. Keep the knives sharp and clean. Make sure the machine has proper ground...
Page 4
Motor lock your newly designed machine base has a motor lock. This new devise allows you to lock your motor in place to keep it from bouncing on the belt during interrupted cuts etc. It also allows you to modify the belt tension which can aid you in achieving the finish quality you are looking for. ...
Page 5
Both molding and planing knives have an edge angle of 57 degrees measured off the back of the knife. Hook angle is 11 degrees the use of dull knives will put a strain on the feed mechanism and will result in your need of a repair. Any problems created due to the use of dull knives are not covered un...
Page 6
8. On some extremely deep or wide cuts, some prior stock removal will be required before molding. You may remove this stock using one of the rabbet knives found in our catalog, or you may use a dado blade on a table saw. 9. Do not cut a wider stock area than the knife was designed to cut. This will ...
Page 7
When planing the edge of stock, a high, square, relieved guide is needed in order to have the edge reasonably square and to provide stability. Use center reliefs to reduce friction. Some profiles are too deep to make on the w&h. In some cases you can rotate the profile into a flatter position to eff...
Page 8
The guides should be 14” long if you are just using the bed of the machine and 20” long if you are using the gs-2 guide system. The guides may be made using the band saw set up. We make one guide for the inside radius and one for the outside radius. We use mdf board. Round top setup 1. Make sure pow...
Page 9
On occasion you may find a light chain imprint on the top of your panel. This mark may be removed when you are finished molding your panel with a thickness planer or sander. Or, you may install a w&h raised panel kit that will eliminate the chain mark entirely. How to plane caution! When you use the...
Page 10: Chatter
Chatter snipe definition snipe is generally an unwanted undercut in the stock. It occurs in the first and last few inches of the stock length. It causes a different height dimension than what was selected for the stock. Causes the stock may be cupped, warped or twisted. The stock experiences a chang...
Page 11
Feeding problems make sure that power is disconnected before inspecting machine! Symptom solution the stock stops but the feed-rollers continue to turn. This is a traction or friction problem. 1) make sure your stock is not binding in the guides. 2) make sure the stock is of consistent width. Saw ri...
Page 12
Instructions for removal of feed roller unplug machine. Take off chip deflector. Raise head. Remove pressure screws over swing arm to be removed. Remove two 54-15 pivot screws and remove swing arm, leaving chain connected to mating sprocket. Reinstall each pivot screw with a drop of medium strength ...
Page 13
Removal of power feed unit 1) disconnect power. Remove chip deflector and raise head 4”-5”. 2) spin the arbor to find the set screw on the in-feed chain sprocket on the underside of the chain guard. Using a 3/32” allen wrench, loosen the set screw. 3) starting with the bolts on the chain guard, remo...
Page 14
Primary shaft p-203 into the end of the arbor with the slot straddling the p-117 fiber drive. Install the three attaching bolts, tightening only the longest bolt. 7) tighten the in feed roller sprocket set screw on its shaft flat with the chain in a straight line position with its mating sprocket. 8...
Page 15
Gear box shaft assemblies 15.
Page 16
Gear box assembly view 16.
Page 17
Arbor removal view 17.
Page 18
Contact information williams & hussey machine co., inc. Customerservice@williamsnhussey.Com (e-mail) 70 powers street milford nh 03055 williamsnhussey.Com (website) 603-732-0219 (local) business hours: monday – friday 800-258-1380 (toll free) 8:30 am – 4:30 pm 603-732-4048 (fax) warranty information...