Wald BICYCLE BASKET Assembly Instructions

LONG SCREW

          2

MOUNTING

HOLDER

         5

LOCK END

             7

HOLDER SLOT

MOUNTING HOLDER

BOTTOM HOOKS

                6

     1

BRACE

HOLDER

TOP BRACKET

              3

           4

HANDLEBAR

CLAMP

SHORT SCREW

LONG SCREW

          2

MOUNTING

HOLDER

         5

LOCK END

             7

HOLDER SLOT

MOUNTING HOLDER

BOTTOM HOOKS

                6

     1

BRACE

HOLDER

TOP BRACKET

              3

           4

HANDLEBAR

CLAMP

SHORT SCREW

LONG SCREW

          2

MOUNTING

HOLDER

         5

LOCK END

             7

HOLDER SLOT

MOUNTING HOLDER

BOTTOM HOOKS

                6

     1

BRACE

HOLDER

TOP BRACKET

              3

           4

HANDLEBAR

CLAMP

SHORT SCREW

BICYCLE BASKET

with handle & mounting holder

- Basket easily removed for carrying

- Sized for grocery bag & many other uses

- Rust resistant durable finish

- Extended Mounting Holder allows clearance for shifters, brake 

  levers & cables

ASSEMBLY INSTRUCTIONS

- Loosely assemble 

1

brace onto two vertical side wires of 

2

holder with short screws. In most cases brace will be angled 

  upward toward Stem as shown.

- Center holder and hang 

3

holder top brackets over handlebar. 

  (If clamping onto 7/8" portion of handlebar, insert rubber spacer 

  strips between holder and handlebar). Loosely assemble two 

4

handlebar clamps with long screws.

- Attach basket to holder

  - Hold basket so 

5

lock end of handle is toward holder.

  - Center basket with holder and insert lower basket frame wire over 

    bottom hooks of holder as shown.

  - Raise handle upright and insert 

5

lock end of handle through 

7

slot at top of holder.

  - Lay handle flat to lock.

- Adjust holder 

1

brace vertically on holder side wires until basket 

  is in proper position.

- Remove basket from holder

  - Raise basket handle upright.

  - Pull away from holder and lift basket from bottom hooks of holder.

- Tighten all holder fittings securely.

Mfgr.No.3133GB (Black)

Made in U.S.A. by Wald

C

2009 Wald LLC

Rev.A 4/8/2009

WARNING

DO NOT overload basket.

Overloading basket may cause difficulty 

in steering and/or loss of bicycle control 

which could result in injury.

!

Mfgr.No.3133GB (Black)

Made in U.S.A. by Wald

C

2009 Wald LLC

Rev.A 4/8/2009

WARNING

DO NOT overload basket.

Overloading basket may cause difficulty 

in steering and/or loss of bicycle control 

which could result in injury.

!

- Loosely assemble 

1

brace onto two vertical side wires of 

2

holder with short screws. In most cases brace will be angled 

  upward toward Stem as shown.

- Center holder and hang 

3

holder top brackets over handlebar. 

  (If clamping onto 7/8" portion of handlebar, insert rubber spacer 

  strips between holder and handlebar). Loosely assemble two 

4

handlebar clamps with long screws.

- Attach basket to holder

  - Hold basket so 

5

lock end of handle is toward holder.

  - Center basket with holder and insert lower basket frame wire over 

    bottom hooks of holder as shown.

  - Raise handle upright and insert 

5

lock end of handle through 

7

slot at top of holder.

  - Lay handle flat to lock.

- Adjust holder 

1

brace vertically on holder side wires until basket 

  is in proper position.

- Remove basket from holder

  - Raise basket handle upright.

  - Pull away from holder and lift basket from bottom hooks of holder.

- Tighten all holder fittings securely.

ASSEMBLY INSTRUCTIONS

- Basket easily removed for carrying

- Sized for grocery bag & many other uses

- Rust resistant durable finish

- Extended Mounting Holder allows clearance for shifters, brake 

  levers & cables

BICYCLE BASKET

with handle & mounting holder

Mfgr.No.3133GB (Black)

Made in U.S.A. by Wald

C

2009 Wald LLC

Rev.A 4/8/2009

WARNING

DO NOT overload basket.

Overloading basket may cause difficulty 

in steering and/or loss of bicycle control 

which could result in injury.

!

- Loosely assemble 

1

brace onto two vertical side wires of 

2

holder with short screws. In most cases brace will be angled 

  upward toward Stem as shown.

- Center holder and hang 

3

holder top brackets over handlebar. 

  (If clamping onto 7/8" portion of handlebar, insert rubber spacer 

  strips between holder and handlebar). Loosely assemble two 

4

handlebar clamps with long screws.

- Attach basket to holder

  - Hold basket so 

5

lock end of handle is toward holder.

  - Center basket with holder and insert lower basket frame wire over 

    bottom hooks of holder as shown.

  - Raise handle upright and insert 

5

lock end of handle through 

7

slot at top of holder.

  - Lay handle flat to lock.

- Adjust holder 

1

brace vertically on holder side wires until basket 

  is in proper position.

- Remove basket from holder

  - Raise basket handle upright.

  - Pull away from holder and lift basket from bottom hooks of holder.

- Tighten all holder fittings securely.

ASSEMBLY INSTRUCTIONS

- Basket easily removed for carrying

- Sized for grocery bag & many other uses

- Rust resistant durable finish

- Extended Mounting Holder allows clearance for shifters, brake 

  levers & cables

BICYCLE BASKET

with handle & mounting holder

A

WALD LLC MAYSVILLE, KY.

DRN

TITLE

APVD

SCALE

DATE

NO.

REVISIONS

ZONE

REV

DESCRIPTION

BY

DATE

CHAD

3133GB BASKET - 

ASSEMBLY INSTRUCTIONS

1:1

9-15-03

C-68019

A

B

C

D

E

F

A

B

C

D

E

F

1

2

3

4

5

6

1

2

3

4

5

6

A

CHAD

4-8-09

REVISED WARNING NOTE - S.V.P.