Watec WAT-2200D Operation Manual
1/2.8” Professional 3G-SDI/HD-SDI Waterproof Color Camera
WAT-2200D
Operation Manual
This operation manual covers safety, camera functions, installation and the
correct operating procedure for the WAT-2200D. First, we ask you to read
this operation manual thoroughly, then install and operate the WAT-2200D
as advised. In addition, for future reference, we also advise safekeeping of
this manual.
Please contact the distributor or dealer from which the WAT-2200D was
purchased, if you do not understand the installation, operation or safety
instructions laid out in this manual. Not understanding the contents of the
operation manual sufficiently may cause damage to the camera.
Guide to the Safety Symbols
When you do not adhere to or take notice of the “Danger” sign,
it may lead to a serious accident such as death or injury
caused by fire or electric shock.
When you do not adhere to or take notice of the “Warning”
sign, it may cause severe damage such as a physical injury.
When you do not adhere to or take notice of the “Caution” sign,
it may incur injury and cause damage to peripheral objects in
the immediate surroundings.
Cautions for Safety
The WAT-2200D is designed to be used safely; however, it may lead to a
physical accident caused by fire and electric shock if not used correctly.
Therefore, please keep and read the “Cautions for Safety” below for
protection against accidents.
Do not disassemble and/or modify the WAT-2200D.
Do not operate any current-carrying part with wet hands.
Use a stabilized power adaptor designed for DC+12V±
10%, with a current capacity of more than 300mA for the
WAT-2200D.
The recommended voltage is DC+12V ± 10%. Also, we
advise the Use of an “inline fuse” power line to protect the
camera and peripheral equipment, where applicable.
Do not use the WAT-2200D under unusual environmental
conditions.
The WAT-2200D is specified as water-resistant. However,
the WAT-2200D is not compliant with dust-proof and
explosion-proof standards.
Should the camera not work properly, switch off the power
immediately. Then check the camera according to the
“Problems and Trouble Shooting” section.
Avoid the striking of hard objects or dropping the
WAT-2200D.
The WAT-2200D uses high quality electrical parts and
precision components and may inadvertently be damaged if
not cared for properly.
Do not connect any power supply directly to the video
out terminal of the unit.
Do not connect the WAT-2200D with any monitor using a
video/power single transmission terminal. The WAT-2200D
utilizes HD-SDI output and is not designed for use with this
type of equipment. We also advise you to read the operation
manual of the monitor you plan to use before any
connections are made.
Do not install the WAT-2200D in a position subject to
direct sunlight.
Sunlight shinning directly onto the WAT-2200D lens can
cause damage to the sensor.
Select a stable place for installation of the WAT-2200D.
Use an appropriately rated mount durable and strong for all
installation position.
Do not move the WAT-2200D with the cables connected.
Before moving the WAT-2200D, always remove the video
cable and power cable from the rear of the camera first.
Avoid using the WAT-2200D near any strong
electromagnetic field.
In the event of exposure to electromagnetic waves (causing
the monitored image to become distorted) we recommend
the camera be shielded by an appropriate protective casing.
Dry the WAT-2200D well after use.
When the WAT-2200D is used in seawater, flush well with
pure water, and then wipe. If the WAT-2200D is steeped in
water for many hours or left without after use, the surface of
the WAT-2200D may become white.
Problems and Trouble Shooting
If any of the following problems occur when using the WAT-2200D,
An optimal picture cannot be obtained, after checking that all the cables
and connections are correctly in place.
Smoke or any unusual odor emerges from the WAT-2200D.
An object becomes embedded or a quantity of liquid seeps into the
camera housing.
More than the recommended voltage or/and amperage has been applied
to the WAT-2200D by mistake.
Anything unusual occurring to any equipment connected to the
WAT-2200D.
Required Action
:
①
Switch off the main power supply to the camera.
②
Remove the power and video cables connected to the WAT-2200D.
③
Contact the distributor or dealer from which the WAT-2200D was
purchased
Waterproof Conformity
The external body of the WAT-2200D is in conformity with the following
waterproof standard.
The protection rating of WAT-2200D is equivalent to IPX8.
IPX8 equivalent:
The camera has no water coming inside and has no defect after dipping
10m depth for 30 minutes into the tank filled with faucet water.
For ⑥ VIDEO OUT and ⑦ POWER IN, this part is not
included in the compatible range of the waterproof standard.
Treat the connecter area for waterproofing if needed.
Problems and Trouble Shooting
①
FRONT CLASS (Tempered glass)
Dirt, water or oil deposits on the front glass will cause an unclear picture on
the monitor and scratches might become permanent damage. Do not
dismount the front glass.
②
HOUSING MAIN BODY
This case is made of aluminum and is given alumite coated.
③
TRIPOD MOUNTING SCREW HOLES
Mounting holes for stands. The size of these threads are 1/4”, 20 threads,
4.5±0.2mm, which is the same as any standard camera tripod (U1/4”).
④
BRACKET
The bracket for fixing to the camera.
⑤
BRACKET MOUNTING SCREWS
The screws for mounting the bracket to the camera.
⑥
VIDEO OUT (BNC)
The terminal for SDI signal output.
⑦
POWER IN
The terminal for connecting the AC adaptor.
Power Supply
Use a stabilized power adaptor designed for DC+12V, with a current
capacity of more than 300mA. Watec recommends our optional AC adapter
(SWI12-12-N-P5 / GF12-US1210, ref. Options).
Set-up and Operation
1） Ensure that the power to the WAT-2200D and the peripheral equipment
is turned off before making any connections.
2） Connect ⑥VIDEO OUT on the WAT-2200D with the monitor, using a
high-frequency coaxial cable with 75 ohm impedance.
3） Insert the power plug of the power adaptor into ⑦POWER IN. Confirm
that the power adaptor is not connected to the power supply before
insertion of the power plug into ⑦POWER IN.
4） Turn on the power to the WAT-2200D, monitor and all other allied
equipment. When a picture cannot be obtained on the monitor, or a
problem occurs, check and follow the procedure mentioned in the
【
Problem and Trouble Shooting】 section.
5） When a change of installation position is required, set ④BRACKET
to
your required position after removing
⑤
BRACKET MOUNTING
SCREWS from the WAT-2200D, then retighten ⑤ BRACKET
MOUNTING SCREWS firmly. Angular settings for ceiling and wall are
also available.
<④BRACKET>
Options
To purchase these options, please contact the distributor or dealer from
which you purchased the WAT-2200D.
AC Adapter (SWI12-12-N-P5)
The optional AC Adapter that can be used to
power the camera from a wall outlet.
The AC Adaptor meets the US Energy
Regulation Level 6.
AC Adapter (GF12-US1210)
The optional AC Adapter that can be used to
power the camera from a wall outlet.
Contact information
Design and specifications are subject to change without notice.
Watec is not responsible for any inconvenience or the attendant damages to
the video and monitoring recording equipment caused by misuse,
miss-operation or improper wiring of our equipment.
If for any reason the WAT-2200D does not work properly, or if you have any
questions regarding installation or operation, please contact the distributor or
dealer from which it was purchased.
Contact information
Watec Co., Ltd.
Add.:
254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,
Yamagata-Ken, 997-0017 Japan
TEL:
+81-235-23-4400 FAX: +81-235-23-4409
Email:
info-o@watec.co.jp
URL:
http://www.watec.co.jp
5090Z00-Y2000004