WaterSoft AS24P Installation and operation manual

Manual is about: Fully Automatic & Demand Water Softeners with 2092 Isobar Control Valve

Summary of AS24P

  • Page 1

    Softener manual installation / operation manual fully automatic & demand water softeners with 2092 isobar control valve.

  • Page 2

    Softener specifications.................................................................................................Page 3 softener installation......................................................................................................Page 5 softener capacity.............................

  • Page 3

    Warning lubricants do not use vaseline, oils, hydrocarbon lubricants or spray silicone anywhere! Petroleum base lubricants will cause swelling of o-rings and seals. The use of other lubricants may attack plastic noryl®. It is recommended that dow corning® silicone grease be used as a lubricant for a...

  • Page 4

    Please note these specifications before proceeding operating pressure range : 20 - 125 psi operating temperature range : 33º f - 120º f inlet / outlet pipe size : 3/4: fnpt please comply with all applicable plumbing codes protect the softener and piping from freezing temperatures please read the ent...

  • Page 5

    Softener specifications -pre-installation check list- a water test should always be performed in order to determine total water hardness (in gpg) and total dis- solved iron (in parts per million - ppm). This is critical for proper equipment selection, sizing and for determining the program for regen...

  • Page 6

    Installation -softener location / other requirements- • locate the unit near an unswitched, 120 volt / 60 hz grounded electrical outlet. • check for distance and proper drain installation (e.G. Floor drain, washing machine standpipe). • determine type and size of piping required for softener connect...

  • Page 7

    Installation -installation procedure- - water supply connections and bypass valve - to allow for softener servicing, swimming pool filling or lawn sprinkling, a manual bypass valve has been installed at the factory. The bypass allows hard water to be manually routed around the softener. 1. Position ...

  • Page 8

    Installation -brine line and overflow connection- 1. Position brine tank on a smooth, level surface near the softener resin tank. If necessary, the brine tank can be placed at a higher level than the resin tank, but never at a lower level. 2. Install one end of 3/8" o.D. By 1/4" i.D. Brine line tubi...

  • Page 9

    Installation installation - control valve options- each control valve position can be manually selected by rotating the regeneration knob clockwise until the desired position appears in the knob notch. 1. Manually index regeneration knob to backwash position and allow water to run to drain for 3-4 m...

  • Page 10

    Capacity model nominal 32,000 grain units (-32) # of people 1 2 3 4 5 6 7 8 9 salt setting 15 lbs. / regeneration hardness range number of tabs to pull 3 - 10 1 1 1 2 2 2 2 3 3 11 - 20 1 2 2 3 3 4 4 4 4 21 - 30 1 2 3 4 6 6 6 12 12 31 - 40 2 3 4 6 6 12 12 12 - 41 - 50 2 3 6 6 12 12 12 12 - 51 - 60 2 ...

  • Page 11

    Capacity capacity model nominal 24,000 grain unit (- 24) # of people 1 2 3 4 5 6 7 8 9 salt setting 12 lbs. / regeneration hardness range number of pins to pull 3 - 10 1 1 1 2 2 2 2 3 3 11 - 20 1 2 2 3 3 4 4 4 4 21 - 30 1 2 3 4 6 6 6 12 12 31 - 40 2 3 4 6 6 12 12 12 - 41 - 50 2 3 6 6 12 12 12 12 - 5...

  • Page 12

    Capacity model nominal 48,000 grain units (- 48) # of people 1 2 3 4 5 6 7 8 9 salt setting 24 lbs. / regeneration hardness range number of pins to pull 3 - 20 1 1 2 2 2 3 3 3 4 21 - 30 1 2 2 3 3 4 4 6 6 31 - 40 1 2 3 3 4 6 6 6 12 41 - 50 1 2 3 4 6 6 12 12 12 51 - 60 2 3 4 6 6 12 12 12 12 61 - 70 2 ...

  • Page 13

    Capacity - setting the regeneration schedule - 1. Locate the program wheel just to right of the manual regeneration knob. (see figure 1.) 2. Rotate program wheel until the white dot located on the outermost gear is aligned with the capacity (gallons) arrow on the control panel. (see figure 1.) 3. Pl...

  • Page 14

    - general care and cleaning - 1. Do not place heavy or sharp objects on water softener or cabinet. 2. Use only mild soap and warm water to clean exterior of the unit. Never use harsh, abrasive cleaners. 3. Protect the water softener and drain line from freezing. 4. Reset time for daylight saving tim...

  • Page 15

    Installing the control valve.

  • Page 16

    710 orange street, ashland, oh 44805 ph 419.289.1500 fax 419.289.1515 www.Watersoftinc.Com.