Wood Shark 2275 Instruction Manual - page 10

Summary of 2275

  • Page 1

    Instruction manual important information: please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. Manuel d’instructions renseignements importants: avant d’utiliser cet appareil, veuillez lire atentivement les ...

  • Page 2

    2 identification (what is what?) chain adjustment tool (bar tool) primer bulb fuel mix fill cap starter housing bar oil fill cap chain front hand guard front handle starter rope on/stop switch muffler idle speed screw bumper spike guide bar chain brake nuts cylinder cover throttle lockout rear handl...

  • Page 3

    3 identification of symbols move on/stop switch to the on position. Slowly press primer bulb 6 times. Pull the starter rope sharply 5 times with your right hand. Pull the starter rope sharply with your right hand until the engine starts. Pull choke/fast idle lever out to the full extent (to the full...

  • Page 4

    4 s do not operate a chain saw that is dam- aged, improperly adjusted, or not com- pletely and securely assembled. Always replace bar, chain, hand guard, or chain brake immediately if it becomes damaged, broken or is otherwise removed. S with the engine stopped, hand carry the chain saw with the muf...

  • Page 5

    5 manufacturer’s chain sharpening and main- tenance instructions. Check tension at regu- lar intervals with the engine stopped, never with the engine running. Make sure the bar clamp nuts are securely tightened after ten- sioning the chain. S begin and continue cutting at full speed. If the chain is...

  • Page 6

    6 from a servicing dealer, or to the nearest au- thorized master service dealer. S tip contact in some cases may cause a lightning fast reverse reaction, kicking the guide bar up and back toward the oper- ator. S pinching the saw chain along the top of the guide bar may push the guide bar rapidly ba...

  • Page 7

    7 cutters depth gauge drive links place chain onto the sprocket 7. Place chain over and behind clutch, fitting the drive links in the clutch drum sprocket. 8. Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar. 9. Fit chain drive links into bar groove. 10. Pull ...

  • Page 8

    8 fueling engine warning : remove fuel cap slowly when refueling. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. A 40:1 ratio is obtained by mixing 0,125 lit...

  • Page 9

    9 chain brake warning : if the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an authorized service dealer if any part is worn to less than 0,02 ″ (0,5 mm) thick. Rep...

  • Page 10

    10 direction of fall 45 _ plan a clear retreat path felling large trees (15 cm in diameter or larger) the notch method is used to fell large trees. A notch is cut on the side of the tree in the de- sired direction of fall. After a felling cut is made on the opposite side of tree, the tree will tend ...

  • Page 11

    11 first cut on pressure side of log second cut first cut on pressure side of log second cut bucking without a support s overcut through 1/3 of the diameter of the log. S roll the log over and finish with a second overcut. S give special attention to logs under strain to prevent the saw from pinchin...

  • Page 12

    12 service and adjustments warning : disconnect the spark plug before performing maintenance, except for carburetor adjustments. We recommend all service and adjustments not listed in this manual be performed by an authorized service dealer. Maintenance schedule check: fuel mixture level before each...

  • Page 13

    13 chain sharpening chain sharpening is a complicated task that requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener. Carburetor adjustments warning : the chain will be moving during most of this procedure. Wear your pro- tective equipment and observ...

  • Page 14

    14 declaration of conformity ec declaration of conformity (only applies to europe) we, husqvarna outdoor products italia, s.P.A. , valmadrera, italy. Tel: +39--0341--203211, declare that the chain saw model woodshark 2775 csi---av from serial numbers 2004--136(n or d) 00001 and onwards (the year is ...

  • Page 15

    15 technical data sheet model: woodshark 2275 engine cylinder volume, cm 3 36 stroke, mm 32 idle speed, rpm 3000 recommended max speed, unloaded, rpm 13000 power kw 1,4 ignition system manufacturer walbro type of ignition system cd spark plug champion electrode gap, mm 0,5 fuel and lubrication syste...