X10 DW534 Operating Instructions

Installation

1. Secure the magnet and switch on the DW534 together

with a rubber band.

2. Install a 9V alkaline battery in the battery compartment

on the DW534.

3. Make sure the switch inside the battery compartment

is set to N.C. (Normally Closed). This is the type of

magnetic switch supplied with the DW534.

4. Press the CODE button on the DW534 with the point

of a pencil.

5. Set the  INSTALL/RUN switch on the Security

Console to INSTALL.

6. Press TEST on the DW534. The Console emits a tone

and the next unused zone indicator lights up.

7. Set the Console's slide switch back to RUN1 or RUN2.

8. To set up additional Door/Window Sensors (up to 16*)

repeat the above steps.

9. Set the DW534’s DELAY switch to MAX to protect a

door or to MIN to protect a window.

10. Remove the rubber band and attach the DW534 to the

door or window frame using the double sided tape or

screws supplied.

*Note: you can install a total of 16 zones in the Console.

This can be a combination of Door/Window Sensors and

Motion Detectors. E.G. 8 Door/Window Sensors AND 8

Motion Detectors. See your Security System Owner’s

Manual for more information.

Door/Window Sensor, Model DW534  Set Up and Operating Instructions

X-10 (USA) Inc., 91 Ruckman Rd., Closter, NJ 07624.  http://www.x10.com

DW534-998DR

When the security system IS armed, opening a door or

window trips the alarm. If the DW534 is set to MIN the

alarm trips instantly. If the DW534 is set to MAX there is

a 30 second delay before the alarm trips after you open the

door or window.

Replacing batteries

Slide the battery compartment cover off and replace the

battery with a 9V alkaline type. After replacing the battery,

the following steps are necessary to determine that the

Console still recognizes the DW534.

1. Place the Console’s slide switch to RUN2.

2. Press TEST on the DW534. If the Console chimes, it

recognizes the DW534 and no fur ther action is

necessary.

If the Console did not chime:

1. Place the Console’s slide switch to INSTALL.

2. Press TEST on the DW534. The DW534’s red indicator

light flashes once, and DW534 transmits a random code

to the console. The Console acknowledges this with a

beep and logs in the DW534 to the next available zone.

To make sure the Console logs the DW534 back into

the same zone it was allocated to before you changed

the battery, wait 4 hours after removing the old battery

before reinstalling (until the zone indicator on the

Console starts flashing).

X-10 (USA) INC. LIMITED 1-YEAR WARRANTY

X-10 (USA) Inc. warrants X-10 products to be free from

defective material and workmanship for a period of one (1)

year from the original date of purchase at retail. X-10

(USA) Inc. agrees to repair or replace, at it’s sole discretion,

a defective X-10 product if returned to X-10 (USA) Inc.

within the warranty period and with proof of purchase.

If service is required under this warranty:

1. Return the defective unit postage prepaid to X-10

(USA) Inc. at the address below.

2. Enclose a check for $4.00 to cover postage and

handling.

3. Enclose a dated proof of purchase.

4. X-10 is not responsible for shipping damage.

TEST

DELAY

MAX

MIN

CODE

Door/Window

Sensor

Operation

When the security system is NOT armed and the Console

is set to RUN2, the Console chimes when you open a door

or window protected by the DW534. The red indicator light

for that zone on the Console also lights up. In RUN1 mode

there are no chimes.