- DL manuals
- Y Advantech
- Network Card
- UNO-2053E
- User Manual
Y Advantech UNO-2053E User Manual
Summary of UNO-2053E
Page 1
Uno-2053e gx2-400 universal network controller with pc card, 2xlan, 2xusb, 2xrs-232, audio user manual.
Page 2
Uno-2053e user manual ii copyright notice the documentation and the software included with this product are copy- righted 2006 by advantech co., ltd. All rights are reserved. Advantech co., ltd. Reserves the right to make improvements in the products described in this manual at any time without noti...
Page 3
Iii product warranty (2 years) advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons ot...
Page 4
Uno-2053e user manual iv ce this product has passed the ce test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from advantech. Fcc class a this equipment has been tested and found to comply ...
Page 5: Chapter
V table of contents contents chapter 1 uno-2053e overview .................................... 2 1.1 introduction ....................................................................... 2 1.2 hardware specifications ................................................... 2 1.3 safety precautions ..........
Page 6
Uno-2053e user manual vi a.7 vga display connector (vga1)................................... 18 table a.8:vga adaptor cable pin assignments ....... 18 a.8 compactflash master/slave jumper setting (jp2) ......... 19 a.9 enhanced ide connector (cn2) .................................... 20 table a.9:id...
Page 7: Uno-2053E Overview
1 uno-2053e overview this chapter gives background informa- tion on the uno-2053e. It shows you the uno-2053e overview and specifications. Sections include: • introduction • hardware specifications • safety precautions • uno-2053e series • chassis dimensions ch ap t e r.
Page 8: 1.1 Introduction
Uno-2053e user manual 2 chapter 1 uno-2053e overview 1.1 introduction are you looking forward to a suitable embedded application ready plat- form (arp) that could shorten your development time and offer rich net- working interfaces to fulfill your extensive needs in different kind of projects? Advan...
Page 9
3 • serial port: two standard rs-232 ports - irq: all ports use the same irq assigned by bios - data bits: 5, 6, 7, 8 - stop bits: 1, 1.5, 2 - parity: none, even, odd - speed: 50~115.2 kbps - data signals: txd, rxd, rts, cts, dtr, dsr, dcd, ri, gnd - max data distance: 50 feet (15.2 meters) • usb in...
Page 10: 1.3 Safety Precautions
Uno-2053e user manual 4 1.3 safety precautions the following sections tell how to make each connection. In most cases, you will simply need to connect a standard cable. All of the connector pin assignments are shown in appendix a. Warning!! Always disconnect the power cord from your chassis when you...
Page 11: 1.4 Uno-2053E Series
5 1.4 uno-2053e series there are two products in uno-2053e series listed as below: • uno-2053e: uno-2053e hardware platform • uno-2053ece: uno-2053e hardware platform with wince os (built in 128mb compactflash card) • uno-2053exp: uno-2053e hardware platform with winxpe os (built in 1gb compactflash...
Page 12: 1.5 Chassis Dimensions
Uno-2053e user manual 6 1.5 chassis dimensions figure 1.1: chassis dimensions.
Page 13: Hardware
2 hardware functionality this chapter shows how to set up the uno-2053e’s hardware functions, includ- ing connecting peripherals, switches and indicators. Sections include: •uno-2053e peripherals •com1~com2: rs-232 interfaces •lan: ethernet connector •power connector •led indicators •ps/2 keyboard a...
Page 14: 2.1 Uno-2053E Peripherals
Uno-2053e user manual 8 chapter 2 hardware functionality 2.1 uno-2053e peripherals the following two figures show the connectors on uno-2053e. The fol- lowing sections give you detail information about function of each peripheral. Figure 2.1: uno-2053e front panel figure 2.2: uno-2053e rear panel 2....
Page 15: 2.4 Power Connector
9 2.4 power connector the uno-2053e comes with a phoenix connector that carries 10~30 vdc external power input, and has reversed wiring protection. There- fore, it will not cause any damage to the system by reversed wiring of ground line and power line. Please refer to a.4 for its pin assignments. 2...
Page 16: 2.10 Reset: Reset Button
Uno-2053e user manual 10 2.9 vga: vga display connector the uno-2053e provides a vga controller for a high resolution vga interface. It supports vga and vesa, up to 1280 x 1024 @ 256 color and 1024 x 768 @ 24bpp resolution and up to 16 mb share memory. The vga interface is reserved for system testin...
Page 17: Initial Setup
3 initial setup this chapter shows how to initial the uno-2053e, sections include: sections include: • insert compactflash card • chassis grounding • connect the power • bios setup and system assignments ch ap t e r.
Page 18: Chapter 3 Initial Setup
Uno-2053e user manual 12 chapter 3 initial setup 3.1 compactflash card installation the procedure for installing a compactflash card into the uno-2053e is as follows, please follows these steps carefully. Step 1: remove power cord. Step 2: unscrew four screws from the rear panel of the uno-2053e. St...
Page 19: Pin Assignments
A pin assignments this appendix shows the uno-2053e pin assignments •board connectors and jumpers •rs-232 serial port •ethernet rj-45 connector •phoenix power connector •ps/2 keyboard and mouse connector •usb connector •vga display connector •compactflash master/slave jumper setting •enhanced ide co...
Page 20: Appendix A Pin Assignments
Uno-2053e user manual 14 appendix a pin assignments a.1 board connectors and jumpers there are connectors and jumpers on the uno-2053e board. The follow- ing sections tell you how to configure the uno-2053e hardware setting. Figure a-1 and figure a-2 show the locations of uno-2053e connectors and ju...
Page 21
15 table a.1: uno-2053e connectors & jumpers cn2 internal ide connector cn3 phoenix power connector cn4 internal compactflash card slot cn6 pc card slot com1 com1 standard rs-232 serial port com2 com2 standard rs-232 serial port con1 usb1 connector con2 usb2 connector d6 ide led d7 power led j1 rese...
Page 22
Uno-2053e user manual 16 a.2 rs-232 serial port 9c (com1~c0m2)(male db9) a.3 ethernet rj-45 connector (lan1~lan2) table a.2: rs-232 serial port pin assignments 1 dcd 2 rxd 3 txd 4 dtr 5 gnd 6 dsr 7 rts 8 cts 9 ri table a.3: ethernet rj-45 connector pin assigns pin 10/100base-t signal name 1 xmt+ 2 x...
Page 23
17 a.4 phoenix power connector (c) a.5 ps/2 keyboard and mouse connector (km1) ps/2 kb/ms connector pin assignments table a.5: table a.4: phoenix power connector pin assigns pin signal name 1 +10~30 vdc 2 gnd table a.6: keyboard & mouse connector pin assigns pin signal name 1 kb data 2 ms data 3 gnd...
Page 24
Uno-2053e user manual 18 a.6 usb connector (con1, con2) a.7 vga display connector (vga1) chipset the uno-2053e uses a amd cs5535 chipset for its svga controller. It supports interlaced and non-interlaced analog monitors (color and mono- chrome vga) in high-resolution modes while maintaining complete...
Page 25
19 a.8 compactflash master/slave jumper setting (jp2) the compactflash interface uses a primary ide channel, which can be set as the master or slave device by changing the setting of jp2. Master device: (default) slave device uno-2053e has one internal compactflash card slot which supports compactfl...
Page 26
Uno-2053e user manual 20 a.9 enhanced ide connector (cn2) table a.9: ide hard drive connector pin assigns pin signal name pin signal name 1 ide reset 2 gnd 3 data 7 (*2) 4 data 8 (*2) 5 data 6 (*2) 6 data 9 (*2) 7 data 5 (*2) 8 data 10 (*2) 9 data 4 (*2) 10 data 11 (*2) 11 data 3 (*2) 12 data 12 (*2...