Summary of Z1
Page 1
Car alarm z1 user´s manual version 1.7 1.
Page 2
Car alarm z1............................................................................................................3 package content.......................................................................................................3 device setup by mobile telephone.............................
Page 3: Car Alarm Z1
Car alarm z1 the car alarm z1 ( further car alarm, or device ) belongs to new generation of modern car security. Thank to integrated gsm module you can control your vehicle with your mobile phone. Car alarm has a special built in sensor that triggers the alarm when the car moves or when it inclines....
Page 4: Password
Device setup by mobile phone setup (control) of device by mobile phone can be done by sending setup sms message to the telephone number of sim card inserted in car alarm. Password each sms message sent to telephone number of sim card inserted in device must begin with access password. Password – it ...
Page 5: Abcd
Recommended to change the password again after the installation, to keep your car and your personal information safe ! Example: to change factory default password „abcd“ to new password „aa22“, write following sms message and send it to the telephone number of sim card inserted in the device: abcd └...
Page 6
Command meaning use pwd=[new password] change password to [new password] [password] └─┘ pwd=1234 sen=[value] [value] defines sensibility (acceleration or vehicle inclination) that will trigger alarm. In general, the lower the value is, the higher is the sensitivity. Allowed range: 3 to 100. Factory ...
Page 7
Abcd └─┘ sen=5 finding out current car alarm settings to find out the current settings of car alarm the question mark is used. ? The question mark is considered an independent command, therefore it must be separated by space. It does not change any setting. If you want to use it, you have to put it ...
Page 8
Setup of telephone numbers command meaning usage t1=[telephone number] t2=[telephone number] t3=[telephone number] t4=[telephone number] [telephone number] determines to which number car alarm will call and send alarm sms messages. It is possible to enter maximum 4 cell phone numbers. [password] └─┘...
Page 9: Setup Of Text Reports
Abcd └─┘ ?S you will receive an answer from your car alarm in this form: abcd └─┘ s0=car alarm z1# └─┘ s1=vehicle stolen# └─┘ s2=battery low# └─┘ s3=battery ok# └─┘ s4=ext. Alarm 1# └─┘ s5=ext. Alarm 2# └─┘ s6=backup battery# in case, that you want to change standard preset text, you can re-write re...
Page 10: Setup Of Control Method
Abcd └─┘ s0=car alarm z1# └─┘ s2=battery low# texts s1, s3, s4, s5, s6, as well as other settings keep unchanged in this case. Setup of control method arming and disarming car alarm is possible in three ways: a) control by ignition key (set by command key) turning on ignition key in ignition box to ...
Page 11: Notice !
Notice ! • to set method of arming and disarming, it is possible to use only one from allowed commands in one message key / rfid / rfidn / arm / disarm . Example: to set the control method write and send sms message: abcd └─┘ key rfid setup when car alarm receives sms message with command rfidn, it ...
Page 12: Reporting Alarm Status
Reporting alarm status alarm status can be triggered by following means: • internal detector of motion / inclination sensor of motion and inclination is a part of device, and in case of move or inclination detection it trigers alarm • external signal inputs • external signal inputs can be connected ...
Page 13: Abcd
When car alarm gets to alarm status, it sends sms messages to all numbers assigned to car alarm. Sms messages contain name of car alarm, type of incident, which triggered alarm, gps coordinates and actual speed, text description of location (if available) and length of last passed journey. Subsequen...
Page 14: Localization Of Vehicle
Starting the vehicle ) , ( rel=status) • usage for other purpose with possibility to control via sms message ( rel=off) or (rel=on) contacts of relay are conducted on cable harness. Relay is switched on for period of 28 seconds from alarm status. Automatic control of car battery auto alarm is standa...
Page 15: Diagnostics
Remarks to device installation before you insert sim card into device, make sure that protection by pin code is deactivated and that data services are activated on your sim card. Device should not be installed in the area, where it would be exposed to high temperatures (for example under the first l...
Page 16
• double beep sounds, that indicates entry to diagnostics mode. Together with that due to security reasons adequate alarm generates. (if you have telephone numbers for alarm reports preset, car alarm will send sms messages and will try to call). • during this mode will actual tests be cyclic indicat...
Page 17
For group 2 a) check, if correct sim card is inserted in device, b) it is necessary that following services are available on your sim card: - voice calls, - sms messages, - data services (gprs), c) check connection of gsm antenna to device for group 3 a) check if gps antenna is turned to the sky by ...