10Bar 10BAR 450D User Manual

Manual is about: Canon Camera Accessories User Manual

Page of 9

Download

Print this page

Bookmark us

Camera Housing – Model 450D (Canon)

User Manual

Contents:

1. Introduction

2. Specifications

3. Function Controls

4. Set up Instructions

5. Use & Care of Housing

6. Service

7. Warranty

1. Introduction

10BAR Underwater Housings are small, light and rugged enough to be used on every dive. Use of a

clear polycarbonate allows for visual inspection of camera condition and the O-ring seal. 10BAR

Housings are designed for the ever -increasing variety of models of digital still and video cameras.

Advanced computer aided design and CNC manufacturing technologies ensure precise dimensions. Each

housing body is first injection molded, and then machined to configure to individual camera model. A

range of lens ports and controls are fitted, to tailor the housing to your camera model.

1 2 3 4 5 6 7 Next › »

Summary of 10BAR 450D

Page 1
Camera housing – model 450d (canon) user manual contents: 1. Introduction 2. Specifications 3. Function controls 4. Set up instructions 5. Use & care of housing 6. Service 7. Warranty 1. Introduction 10bar underwater housings are small, light and rugged enough to be used on every dive. Use of a clea...
Page 2
2 2. Specifications 450d test pressure housings are individually tested to 10 bar (90 m / 300 ft.) recommended working pressure 60 m. Closure design o-ring, air lock body material polycarbonate overall size 200 x 300 x 230 mm (lxwxh) total weight approximately 2.6 kg (housing only) buoyancy (with ca...
Page 3
3 4. Set up instructions 4.1 air lock : the body and lid are designed with the air lock system “no clip” closure arrangement. Testing has shown that this arrangement allow the water to exert an even pressure on the o-ring, increasing the reliability of the watertight seal. 4.2 pressure release plug ...
Page 4
4 4.4 special note on responsibility for watertight integrity: each housing is individually inspected and hydrostatically tested in the factory. The design of the main piston o-ring seal is among the most reliable in the industry and the watertight integrity is excellent. This special o-ring design ...
Page 5
5 contamination such as dust, hair, salt, sand etc. Has fallen onto the o-ring or o-ring recess, as a precaution we recommend to inspect the o-ring every time the lid is opened and to carry out the maintenance if necessary. Procedure: • place the lid on a firm non-slip level surface. • the o-ring ca...
Page 6
6 4.7 mounting the flashlight in the housing remove the lens cap and wrist strap. The pressure release plug should be pulled out before inserting the camera. Attach the plastic slide tray to the camera¡s tripod mounting fixture with a coin, screwdriver or the end of the universal tool supplied (fig....
Page 7
7 5. Use & care of housing: 5.1 pre dive function check. Just before entering the water, make a habit of reviewing the proper steps to close the housing and connect the bulkhead. Make a visual check of the o-ring seal. It is also useful to switch on the camera, and check that controls e.G. On/off, z...
Page 8: 7. Warranty
8 5.4 transportation. Please protect the housing during transportation. It is recommended to remove the handle, and shutter extension, and wrap the camera in foam or bubble wrap. 5.5 accidents. The impact resistance of the housing is excellent. However after an accident the alignment of the housing ...
Page 9
9 (copy to be retained by user) housing type date of purchase serial number : (labelled inside housing) dealer : owner’s name : e-mail : owner’s address: tel : fax : office & showroom: unit c, 2/f., wing hin factory building, 31-33 ng fong st., san po kong, hong kong. Tel: (852) 2573 3228 fax: (852)...