10Bar G10 User Manual

Manual is about: Canon

Page of 10

Download

Print this page

Bookmark us

Camera Underwater Housing

G10 (Canon)

User Manual

Contents:

1. Introduction

2. Specifications

3. Function Controls

4. Set up Instructions

5. Use & Care of Housing

6. Service

7. Warranty

1. Introduction

Made of 6061 aluminum, 10Bar Housing is a sturdy choice for the G10 camera. For those who favor small

cameras, it is the ideal housing to suit their needs. It is equipped with full-function control buttons, bulkhead

connector for external flash and interchangeable ports for conversion lens. The acrylic lid allows taking pictures

and checking on the camera much easier. For closure, the double o-rings and key-hole lock design provide ease

of use and added security. Now you can use small cameras with the feel and function of professional housings.

2. Specifications

Test Pressure

Housings individually tested to 10 Bar (90 m / 300 ft.) Recommended working

pressure 60 m

Closure Design

Double O-rings, Key hole lock

Body Material

6061 Aluminum, Acrylic

Overall Size

136 x 152 x 117mm (L x W x H)

Total Weight

Approximately 940g (Housing only)

Buoyancy (with camera)

Slightly negative in salt water

1 2 3 4 5 6 7 Next › »

Summary of G10

Page 1
1 camera underwater housing g10 (canon) user manual contents: 1. Introduction 2. Specifications 3. Function controls 4. Set up instructions 5. Use & care of housing 6. Service 7. Warranty 1. Introduction made of 6061 aluminum, 10bar housing is a sturdy choice for the g10 camera. For those who favor ...
Page 2: 3. Function Controls
2 accessories spare main o-rings ( included) silicone o-ring grease ( included) carrying bag ( included) red filter (optional) extension arm for strobe or video light (optional) macro and wide angle converter (optional) dome port and extension adaptor (optional) housing for 580exii flash (optional) ...
Page 3: 4. Set Up Instructions
3 (3) mode dial - press down and turn to activate the required mode. (4) iso speed dial - press down and turn to adjust the iso value. (5) shutter / zoom - press to activate the shutter, turn to activate the zoom function (separate controls on some version). (6) power on/off - align the white dot to...
Page 4
4 4.2 maintaining the o-ring seal if the main body to lid o-rings are not installed, install the o-rings before diving. Their care and maintenance are critical to the watertight integrity of the housing. If the o-rings are contaminated, or not already installed; inspect, grease and install the o-rin...
Page 5
5 • if the o-ring is damaged or suspected of being damaged, discard it immediately . A spare o-ring is supplied with the housing, or a replacement o-ring can be ordered from 10 bar. If the o-ring is contaminated or suspected of being contaminated, clean it with a cotton cloth that is free of all che...
Page 6
6 replace the lid and make sure the lever is perpendicular to the side wall of the housing. Lock the lid by press down the lever and turn until the lever is parallel to the side wall of the housing. After replacing and locking the lid, make a final visual inspection of the main o-ring for contaminat...
Page 7
7 mounting the camera into housing and close the lid mounting the port adaptor for housing mounting conversion lens mounting dome port there are o-rings on all the components of the port parts which should be installed according to the procedures at 4.3..
Page 8
8 4.6 using external strobes: the standard bulkhead is sf6 (subtronic, ttl). Bulkhead nkf5(2) (nikonos. Non-ttl) or other type to be custom- made as requested. Check the o-rings and connect the strobe sync cord to housing’s bulkhead. Tighten the lock ring to secure the cord in place. Make sue that t...
Page 9: 6. Service
9 5.4 transportation. Please protect the housing during transportation. It is recommended to remove the handle, and shutter extension, and wrap the camera in foam or bubble wrap. 5.5 accidents the impact resistance of the housing is excellent. However after an accident the alignment of the housing m...
Page 10: 7. Warranty
10 7. Warranty the warranty is valid within two years from the date of first purchase. The warranty applies only to the housing itself. 10bar does not accept any liability either implicit or otherwise for any equipment housed inside, or used together with the housing. In the event of the housing flo...