1100 Energy SBP-1100e User Manual - page 8
4
| Eleven Hundred Energy Corporation
Supplying Power to a Load
TousetheSBP-1100etopoweraDCload,firstdeterminewhetherthefixedvoltageprovidedbytheSBP-1100e(e.g.
13.8VDCor25.3VDC,etc)isappropriatefortheload,andthatthepowerdemandedbytheloadwillnotexceed300
watts on a continuous basis. If continuous power in excess of 300 watts is required, consult 1100 Energy.
Connect the SBP-1100e power output jack on the right side of the unit to the load using the provided cable or other
approved cable. A short output cable terminated with ring terminals, provided by 1100 Energy, may be used to con-
nectwithanother,longer,user-providedcableifappropriate.User-specifiedextensioncablesshouldbeofawiregauge
adequate to avoid an excessive voltage drop in the extension cable.
The panel display may be controlled to show the voltage, current and an estimate of the remaining battery pack charge
as a percentage of the charge capacity. The SBP-1100e may be used to provide power to a load while the battery pack
is being charged.
If the SBP-1100e becomes fully discharged, and the output cuts off, a small amount of residual stored energy will
maintain functionality of the user interface for one hour or more. This feature is partly for user convenience during at-
tended operation and testing, and it also keeps the serial control and monitor interface functioning. If no new charge is
added after the output cuts off, the user interface will cut off as well, after 30 minutes, and the unit will then appear to
be totally dead, with no power output, no display, and no response to button pressing. The SBP-1100e is in hibernation.
However, the user interface will come back to life within 3 seconds after external power is applied, and after a suitable
period of charging, the SBP-1100e battery pack may again be used normally. In the event that charging power is applied
aftertheoutputhasbeencutoff,thestateofchargemustrisetoabout15%beforetheoutputwillbeturnedonagain.
Power Output ‘On’ and ‘Off’ Control
Tochecktheoutputvoltageandcurrent,pressthe‘SCROLL’buttonontheControlPanelrepeatedly(slowly)untilthe
second line of text of the LCD display shows the output voltage and current, for example:
Out 13.8V 00.0A
This display will persist for eight seconds, during which time the ‘SELECT’ button may be pressed to toggle the power
output ‘on’ and ‘off’. That is, if the power output is ‘on’, pressing “SCROLL’ once will turn it off, and if the power output is
‘off’, pressing “SCROLL’ once will turn it on. The change in output voltage and current resulting from turning the output
‘on’or‘off’willnotappearimmediatelyontheLCDdisplay,becausethedisplayisafrozensnapshotofthestateexist-
ing when the ‘SCROLL’ button was pressed. To see the new output voltage and current, again press the ‘SCROLL’ button
repeatedly(slowly)untilthenewdataisdisplayed.NotethatifthereisnoloadconnectedtotheSBP-1100eandthe
power output is turned off, it may take 30 seconds or more for the indicated output voltage to fall below one volt, due to
storedchargeintheoutputregulationcircuit.Ifaloadispresent,theoutputvoltagewillinstantlydroptozerowhenthe
output power is turned off.
The SBP-1100e has a very high power and energy density. Mishandling may present a risk of fire or explosion. Exer-
cise common sense precautions when handling, transporting, or testing. DO NOT OPEN the battery pack case and
replace individual cells or modules. Usage should be carefully coordinated with 1100 Energy to ensure proper opera-
tion and safety.