2gig Technologies 2GIG-CP2 Installation & Programming Instructions - Q-4

29

Installer Programming

RF Keypad Programming  Steps

Q-4 

Select  RF keypad # (1-4)

Up to four wireless keypads can be used with each Control Panel. The options for 

each sensor are programmed with sub-option questions.

•  Begin by entering the RF keypad number or 

select it using the 

← or → arrows.

•  Program the RF keypads by using the 

↑ and ↓ 

arrows to select the sub-options.

✓ NOTE: To skip RF keypad programming, press SKIP to jump from 

question Q-4 to question Q-5 (Exit Delay programming).

Select RF keypad (#) used (0-1)

DEFAULT: Unused (0)

RF keypads can be used with the Control Panel or not.

•  The default (0) sets all RF keypads as unused.

•  To enable programming for this RF keypad, select used (1).

Select  RF keypad (#) equipment code (0-9999)

DEFAULT: (0000) other

The RF keypad equipment code defi nes the sensor’s manufacturer and type.

•  The default is (0000) other.

•  Select (867) PAD1-345 wireless keypad for a 2GIG-PAD1 RF keypad.

•  Select (1059) TS-1 wireless touchscreen keypad for 

a 2GIG-TS1 Wireless Touch Screen Keypad.

✓ NOTE: The TS-1 wireless keypad is not for UL985 installations.

Enter  RF keypad (#) other equipment code (0-9999)

DEFAULT: 0

✓ NOTE: This question is only displayed if “(0000) other” is 

selected for an RF keypad’s equipment code.

The equipment code is a 4-digit code that is assigned to the model of keypad 

being used.

•  Enter the equipment code number for the RF keypad.

Enter  RF keypad (#) serial number (7 digits)

DEFAULT: 0000000

or

RF keypad (#) keypad id (read-only)

RF keypad serial numbers for standard keypads can be manually entered or 

learned from the RF keypad. Model 2GIG-TS1 wireless touch screen keypads 

serial numbers can only be learned from the keypad.

Standard Keypads:

•  For manual entry, enter the RF keypad number that 

was logged for the RF keypad being programmed. Use 

the SHIFT button to access alpha characters.

•  For automatic entry, press SHIFT then press LEARN. 

The Control Panel will wait for an RF keypad transmission. 

Trigger the RF keypad being programmed, and the Control 

Panel will learn the RF keypad’s serial number.

TS1 Wireless Touch Screen Keypads:

•  For 2GIG-TS1 Wireless Touch Screen Keypads press LEARN. The Control 

Panel will display “Pair with TS-1. Initiating learning process.” Press the 

TS1 keypad’s PAIR WITH PANEL button. Both the TS1 and the Control 

Panel will display “The learn operation succeeded” when complete.

•  The Control Panel will display “RF keypad (#1-4)” for keypad identifi cation.

•  The TS1 will display “Network ID: xxxx” which is the unique 

serial number identifying the specifi c keypad.

• Press OK on both the Control Panel and TS1 to continue.

✓ NOTE: The Model 2GIG-TS1 wireless touch screen keypad will 

display “The security system is temporarily not operational” after 

learning the keypad. This is normal, and will be displayed anytime the 

Control Panel is in system confi guration (programming) mode.

Select  RF keypad (#) equipment age (0-1)

DEFAULT: New (0)

The Control Panel can be used with new or existing RF keypads.

•  If this RF keypad is new for the installation, leave the default of new (0).

•  If this RF keypad is already installed, select existing (1).

Select  RF keypad (#) emergency keys (0-1)

DEFAULT: Enabled (1)

✓ NOTE: This step is not displayed for Model 2GIG-TS1 keypads.

Standard RF keypads have 24-hour emergency buttons labeled FIRE and 

POLICE.

•  The default (1) enables this RF keypad’s emergency keys.

•  To disable this RF keypad’s emergency keys, select disabled (0), 

the keys will not be able to trigger an alarm or report.

✓ NOTE: The RF keypad’s POLICE button will trigger a silent alarm 

if programming question Q-16 is set to silent panic.

TO ENSURE SENDING A SIGNAL, BE SURE TO INSTRUCT THE END USER 

TO PRESS THE RF KEYPAD EMERGENCY KEYS UNTIL THE KEYPAD’S 

INDICATOR LIGHTS.

Construct  RF keypad (#) voice descriptor

DEFAULT: Keypad (#)

The voice descriptor is the words the Control Panel will announce for this RF 

keypad. Up to fi ve words are allowed.

• Press INSERT to place a word from the vocabulary into the data entry fi eld.

• Use the 

← or → arrows to scroll through the words, 

or enter the word’s 3-digit index number.

• Press INSERT again for the next word. Up to fi ve words are allowed.

•  To remove a word, press DELETE.