2gig Technologies TS1 Installation Instructions
2GIG-TS1
Touch Screen
Wireless Keypad
For Remote Control of
the 2GIG Security System
Installation Instructions
PRODUCT DESCRIPTION
The Model 2GIG-TS1 Touch Screen Wireless Keypad is a remote control device
designed for the 2GIG security system Control Panel. The keypad supports all
operating and emergency functions of the system.
The keypad is designed for
indoor use only.
The front panel
and
buttons serve as controls as well as indicators.
Pressing the
button displays emergency icons on the display for Panic, Fire,
and Emergency alarm activation (each has programmable options and can be
enabled or disabled). Pressing the
button changes the system display to the
Home Screen. The keypad is powered from a plug-in power supply (included).
The 2GIG-TS1 exchanges information through a secure 2-way wireless connection
with the Control Panel. Before operation the keypad must be “paired” with the
Control Panel. Refer to the Control Panel’s installation instructions for details on
pairing the keypad to the Control Panel.
KEYPAD PREPARATION
LOCATING THE KEYPAD
WALL MOUNTING THE KEYPAD
CONNECT POWER WIRES TO KEYPAD
CLOSE KEYPAD
CONNECT POWER SUPPLY
INSTALL POWER SUPPLY
PAIR KEYPAD WITH CONSOLE & TEST
LIMITED WARRANTY
This 2gig Technologies Inc. product is warranted against defects in material
and workmanship for twelve (12) months.
This warranty extends only to
wholesale customers
who buy through 2gig Technologies Inc. authorized
distribution channels.
2gig Technologies Inc. does not warrant this product to
consumers.
Consumers should inquire from their selling dealer as to the nature
of the dealer’s warranty, if any.
There are no obligations or liabilities on the
part of 2gig Technologies Inc. for consequential damages arising out of
or in connection with use or performance of this product or other indirect
damages with respect to loss of property, revenue, or profit, or cost of
removal, installation, or reinstallation.
All implied warranties, including implied
warranties for merchantability and implied warranties for fitness, are valid only until
the warranty expires.
This 2gig Technologies Inc. Warranty is in lieu of all other
warranties express or implied.
IMPORTANT !!!
Radio controls provide a reliable communications link and fill an important need
in portable wireless signaling. However, there are some limitations which must be
observed.
For U.S. installations only: The radios are required to comply with FCC Rules and
Regulations as Part 15 devices. As such, they have limited transmitter power and
therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be
blocked by radio signals that occur on or near their operating frequencies, regardless of
code settings.
Changes or modifications to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
A general knowledge of radio and its vagaries should be gained prior to acting as a
wholesale distributor or dealer, and these facts should be communicated to the ultimate
users.
This device complies with FCC Part 15 and Canada Rules and Regulations.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
PRINTER’S INSTR
UCTIONS:
GUIDE, USER,
TS1 - FILE NAME:
231814 B - INK:
BLA
CK - MA
TERIAL:
20 LB
. MEAD BOND - SIZE:
14.000”
X 8.500”
- SCALE:
1-1 - SIDE 1 OF 2
POWER
SUPPLY
LEFT
TERMINAL
+ 14 VDC
RIGHT
TERMINAL
- 14 VDC
CONNECT POWER
WIRES TO THE
POWER SUPPLY
OBSERVE
PROPER
POLARITY !!!
TO KEYPAD
18 AWG / 2-CONDUCTOR
BRACKET
INSTALLED
FOR STANDARD
STYLE OUTLET
POWER
SUPPLY
POWER
SUPPLY
BRACKET
INSTALLED
FOR DECORA
STYLE OUTLET
USE THE KEYPAD'S BACK COVER AS A TEMPLATE
TO MARK THE THREE SCREW HOLES AND THE
POWER WIRING ACCESS HOLE
SELECT A LOCATION FOR THE KEYPAD,
BE SURE THAT AC POWER IS AVAILABLE NEARBY,
WATCH OUT FOR STUDS, ELECTRICAL, & PIPES IN THE WALL
USE A DRYWALL SAW TO CUT THE WIRING HOLE
LOOSEN CASE SCREW
FOUR TURNS
DISCONNECT THE
HANGING STRAP
FLIP OPEN THE BACK COVER
OF THE KEYPAD
THE BACK COVER IS USED
AS THE KEYPAD'S MOUNTING PLATE
1
2
3
RE-CONNECT THE
HANGING STRAP
OBSERVE
POLARITY !!!
USE #6 INSULATED SPADE
TERMINALS (NOT SUPPLIED)
TO CONNECT WIRES FROM
THE POWER SUPPLY TO
THE KEYPAD
SNAP CASE CLOSED
TIGHTEN CASE SCREW
PLACE THE CONSOLE IN
PROGRAMMING MODE
AND PREPARE IT FOR ENROLLING
THE WIRELESS KEYPAD
REFER TO THE CONSOLE'S
INSTALLATION INSTRUCTIONS
FOR DETAILS ON PROGRAMMING
AND TESTING THE WIRELESS KEYPAD
2GIG CONSOLE
TS1 WIRELESS
KEYPAD
WHEN
LEARN IS PRESSED ON
THE CONSOLE, AND
PAIR WITH PANEL
IS PRESSED ON THE TS1, THE TWO
UNITS WILL COMMUNICATE AND
AUTOMATICALLY ENROLL THE KEYPAD
ROUTE 18 AWG WIRE
BETWEEN THE KEYPAD
AND THE POWER SUPPLY
LOCATION
USE THE THREE SCREWS AND
ANCHORS SUPPLIED TO ATTACH
THE MOUNTING PLATE TO THE WALL
WIRE GAUGE CHART
GAUGE
MAXIMUM RUN
18
100 FEET
16
150 FEET
USE UN-SHIELDED 2-CONDUCTOR