1. DL manuals
  2. 2N
  3. Microphone
  4. Sip mic
  5. Configuration Manual

2N Sip mic Configuration Manual

Manual is about: Microphone console

Summary of Sip mic

  • Page 1

    Www.2n.Cz 2n sip mic microphone console configuration manual firmware: version: 1.0

  • Page 2

    The 2n telekomunikace a.S. Is a czech manufacturer and supplier of telecommunications equipment. The product family developed by 2n telekomunikace a.S. Includes gsm gateways, private branch exchanges (pbx), and door and lift communicators. 2n telekomunikace a.S. Has been ranked among the czech top c...

  • Page 3

    2n telekomunikace a.S., www.2n.Cz 3/76 content: 1. Product overview 1.1 components and associated products 1.2 terms and symbols 2. Description and installation 2.1 before you start 2.2 electric installation 2.3 product description 3. Function and use 3.1 configuration 3.1.1 system status 3.1.2 netw...

  • Page 4

    2n telekomunikace a.S., www.2n.Cz 4/76 1. Product overview here is what you can find in this section: 1.1 components and associated products 1.2 terms and symbols.

  • Page 5

    2n telekomunikace a.S., www.2n.Cz 5/76 basic properties 2n sip mic ® is an ip microphone console playing live or pre-recorded announcements to up to 12 zones. Together with the 2n sip speakers, provides a 2n sip mic ® complete voice announcement distribution system. However, is more 2n sip mic ® tha...

  • Page 6

    2n telekomunikace a.S., www.2n.Cz 6/76 advantages of use clear and loud speech announcement planner vapix support ® easy control easy one-cable installation (ethernet + poe) voip pbx support (sip) remote control via dtmf or http commands integrated administration web server streamed audio support ap...

  • Page 7

    2n telekomunikace a.S., www.2n.Cz 7/76 basic features 10/100base-tx lan interface 12 – 30 v dc / 2 a or poe 802.3af supply integrated speakers and top-quality microphone in package caution this product, its installation and configuration are not intended for persons with physical, sensory or mental ...

  • Page 8

    2n telekomunikace a.S., www.2n.Cz 8/76 1.1 components and associated products main unit part no. 914431e 2n sip mic ®.

  • Page 9

    2n telekomunikace a.S., www.2n.Cz 9/76 power supply part numbers: 91378100 91378100e 91378100us poe injector – without cable poe injector – with eu cable poe injector – with us cable for power supply of intercom via ethernet cable when poe switch is not available. Part no. 914102x stabilised 12 v / ...

  • Page 10

    2n telekomunikace a.S., www.2n.Cz 10/76 1.2 terms and symbols the following symbols and pictograms are used in the manual: safety always abide by this information to prevent persons from injury. Warning always abide by this information to prevent damage to the device. Caution important information f...

  • Page 11

    2n telekomunikace a.S., www.2n.Cz 11/76 2. Description and installation here is what you can find in this section: 2.1 before you start 2.2 electric installation 2.3 product description.

  • Page 12

    2n telekomunikace a.S., www.2n.Cz 12/76 2.1 before you start product completeness check before installing this product, check whether the product delivery includes: 1x 2n sip mic ® quick user manual installation conditions 2n sip ® mic is to be connected to the lan. 2n sip mic ® is designed for indo...

  • Page 13

    2n telekomunikace a.S., www.2n.Cz 13/76 2.2 electric installation electric installation step by step it is very easy to connect elec 2n sip mic ® trically. Just find the connectors and controls for initial connection on the back panel : connect the additional microphone to the upper connector, conne...

  • Page 14

    2n telekomunikace a.S., www.2n.Cz 14/76 microphone connection lan connection sip mic 2n ® can be connected to a standard local area network using a lan interface via the rj-45 connector on the back panel. Always use cat-5d or higher class cables for reliability reasons. The interface supports 1 0/10...

  • Page 15

    2n telekomunikace a.S., www.2n.Cz 15/76 lan connection the lan interface is equipped with the auto mdix function for automatic straight or cross-over cable detection. The lan interface can also be used for the power supply through active 2n ® sip mic network elements or injectors meeting the ieee 80...

  • Page 16

    2n telekomunikace a.S., www.2n.Cz 16/76 connect the device via the power jack on the back side as shown in the 2n sip mic ® figure below. Power supply connection consumption with different power supplies: 2n sip mic ® power supply consumption poe, ieee 802.3af 8 w 12 v / 2 a 25 w warning if you use ...

  • Page 17

    2n telekomunikace a.S., www.2n.Cz 17/76 2.3 product description is an ethernet sip console designed for public sound distribution. 2n sip mic ® 2n sip ® can be connected to a sip proxy and communicate with the server via phone calls. Mic this guarantees compatibility with all the supported sip-based...

  • Page 18

    2n telekomunikace a.S., www.2n.Cz 18/76 control layout controls 2n sip mic ® legend: ... Call answer / mute button a ... Call extension button b ... Function buttons 1 to 12 for playing/announcing to zone c ... Bar graph – microphone drive indicator d ... Microphone din connector e ... Integrated sp...

  • Page 19

    2n telekomunikace a.S., www.2n.Cz 19/76 controls 2n sip mic ® button function states each button is backlit. Different backlight colours signal different user states. See below. Call pick-up / mute button colour behaviour state action upon press white shining at relax none green flashing incoming ca...

  • Page 20

    2n telekomunikace a.S., www.2n.Cz 20/76 call hang-up button colour behaviour state action upon press white shining at relax none red shining incoming / outgoing call hang up / reject function buttons colour behaviour state action upon press white shining at relax none white flashing message playing ...

  • Page 21

    2n telekomunikace a.S., www.2n.Cz 21/76 colour behaviour state action upon press red shining call error or end none, automatic end with announcement after message you can skip over the announcement and end the call immediately. Connector layout connectors 2n sip mic ® connectors and controls: power ...

  • Page 22

    2n telekomunikace a.S., www.2n.Cz 22/76 mic input – 3.5 mm jack for optional microphone connection line out – 3.5 mm jack for headset / external speaker connection refer to the technical parameters for more details. Press the button on the device bottom to delete all the parameters factory reset inc...

  • Page 23

    2n telekomunikace a.S., www.2n.Cz 23/76 3. Function and use basic functions: sip call support multicast announcements vapix(r) announcements sip voip announcements voice announcements pre-recorded announcements alarm calls with dtmf announcements http/https request sending multicast listening sip ca...

  • Page 24

    2n telekomunikace a.S., www.2n.Cz 24/76 3.1 configuration configure 2n sip mic ® via a pc equipped with any internet browser: launch your internet browser (internet explorer, firefox, etc.). Enter the ip address (e.G. ). 2n ® sip mic http://192.168.1.100/ enter the username and password to log in. A...

  • Page 25

    2n telekomunikace a.S., www.2n.Cz 25/76 1. 2. Note be sure to enter the button sequence within 10 seconds after the sound signal activation for security reasons. The button press timeout is 2 s. Dhcp is active after factory reset and the device obtains the ip address automatically. If you switch dhc...

  • Page 26

    2n telekomunikace a.S., www.2n.Cz 26/76 helios ip network scanner 2n ® installation wizard after installing the application, run the 2n ® helios ip network scanner application using the menu of the microsoft windows operating system. Start upon launch, the application starts searching the lan automa...

  • Page 27

    2n telekomunikace a.S., www.2n.Cz 27/76 helios ip network scanner 2n ® window select the to be configured. Click on it with the right-hand mouse 2n ® sip mic button and select to open the web browser window, log in to browse... And start configuring as described in the login subsection below. 2n ® s...

  • Page 28

    2n telekomunikace a.S., www.2n.Cz 28/76 if the login screen does not appear, an incorrect ip address was entered into the web browser or the administration web server was turned off. If you are not 2n ® sip mic sure of the ip address of , use the 2n ® sip mic 2n ® helios ip network scanner applicati...

  • Page 29

    2n telekomunikace a.S., www.2n.Cz 29/76 the start screen is also the first menu level and quick navigation (click on the pencil symbol) to selected 2n sip mic ® configuration sections. Some tiles also show selected service states. Configuration menu 2n sip mic ® configuration consists of 9 main menu...

  • Page 30

    2n telekomunikace a.S., www.2n.Cz 30/76 network – lan connection settings lan voip – sip proxy, codecs, etc. Settings settings – second call settings common – line state info status audio – ringing volume and key beep settings settings buttons button action settings zones zone parameter settings act...

  • Page 31

    2n telekomunikace a.S., www.2n.Cz 31/76 3.1.1 system status the menu provides a clear survey of current state and system status 2n sip mic ® information. The page is divided into six sections: , , sip proxy line status operation time , , and . Some sections provide just lock state network device dat...

  • Page 32

    2n telekomunikace a.S., www.2n.Cz 32/76 the sip line can be operated without registration. However, you cannot receive incoming calls as the sip proxy does not know where to find the device. Outgoing calls are not affected by this mode. Operation time provides information on the operation time from ...

  • Page 33

    2n telekomunikace a.S., www.2n.Cz 33/76 3.1.2 network 2n sip mic ® is connected to the local area network with a valid ip address, which must be properly set or obtained from the dhcp server in the lan. Configure the ip address and dhcp server on the network tab. Tip to find your intercom ip address...

  • Page 34

    2n telekomunikace a.S., www.2n.Cz 34/76 – static ip address. The address is used together with the parameters ip address below unless activate dhcp is selected. – set the network mask. Ip mask – default gateway address for communication with devices outside ip gateway the lan. Ip dns 1 – primary dns...

  • Page 35

    2n telekomunikace a.S., www.2n.Cz 35/76 3.1.3 voip there are three sip telephony sections in this menu. Use the settings to set relevant call setup parameters, proxy and registration server addresses, codec parameters and priorities and special actions during calls. Common helps you define how the d...

  • Page 36

    2n telekomunikace a.S., www.2n.Cz 36/76 – enter the opponent ip address (operator, pbx) to which sip proxy ip* 2n sip ® should connect for call direction. Mic – set the sip proxy listening port (typically 5060). Port – allow registration with the opponent and specify the phone use registration numbe...

  • Page 37

    2n telekomunikace a.S., www.2n.Cz 37/76 – define the keep-alive packet sending period. The default refresh rate value is 600 s. – enter the public ip address and nat port to which signalling messages nat ip shall be sent by the opponent. Packets are then sent to the pbx as defined in the port routin...

  • Page 38

    2n telekomunikace a.S., www.2n.Cz 38/76 others – select receiving sip receive sip from any ip address (not only from sip proxy) messages from addresses other than sip proxy. Used for direct calling to an ip address, for example. – allow sending 200 ok and bye send 200 ok and bye after call rejection...

  • Page 39

    2n telekomunikace a.S., www.2n.Cz 39/76 common – this parameter is applied connect microphone automatically at incoming call only if automatic call answering is selected (voip / settings / others menu). If you answer calls manually, it is not applied. – set how to handle a call that comes in while h...

  • Page 40

    2n telekomunikace a.S., www.2n.Cz 40/76 – display the set ip address for nat if used. 0.0.0.0 is displayed when nat ip stun server or local ip is used..

  • Page 41

    2n telekomunikace a.S., www.2n.Cz 41/76 3.1.4 audio settings ringing volume – set the device ringing volume (incoming call tone). – enable/disable the key beep. Key beep see the device back panel for more volume and sensitivity controls. The line in signal gain is achieved mechanically using a rotar...

  • Page 42

    2n telekomunikace a.S., www.2n.Cz 42/76 3.1.5 buttons assign one of seven available functions to the buttons on this page. See 2n sip mic ® the button survey below. Logic inputs are located below the call controlling buttons on the device back side. By default, all the available buttons are inactive...

  • Page 43

    2n telekomunikace a.S., www.2n.Cz 43/76 outgoing call destination – set the destination (phone number or ip uri) to which the call shall be directed via sip proxy. – set the call connection beep for . This call connection beep 2n sip mic ® selection is inactive by default. – activate the relay at ca...

  • Page 44

    2n telekomunikace a.S., www.2n.Cz 44/76 http request http request – set the http request to be sent from 2n sip mic ® when a button is pressed. – set the count of http request sending retries if unsuccessful: retry count 0 to 30. The default value is 0. – set the timeout in seconds for http request ...

  • Page 45

    2n telekomunikace a.S., www.2n.Cz 45/76 – set the dtmf code to be sent from when a button is dtmf 2n sip mic ® pressed. Set the dtmf sending method in the voip menu. – play the dtmf code using the speaker. Listening mode 2n sip mic ® – define the call hang-up. The options are automatic call hang-up ...

  • Page 46

    2n telekomunikace a.S., www.2n.Cz 46/76 – enable playing announcements before announcement before voice message voice messages. Load a message of your own in the system messages / voice messages menu. Disabled by default. – set the audio source to be used for announcements. The default audio source ...

  • Page 47

    2n telekomunikace a.S., www.2n.Cz 47/76.

  • Page 48

    2n telekomunikace a.S., www.2n.Cz 48/76 3.1.6 zones find 12 pre-defined zone positions in the menu. Activate the zones using a button. If set yet inactive, a zone cannot be called or announced to. Click the trash bin to delete a row setting. The following options are shared by all the zones: – on or...

  • Page 49

    2n telekomunikace a.S., www.2n.Cz 49/76 – set the audio codec for outgoing rtp packet encryption: g.711a audio codec (alaw) or g.711u (ulaw). Multicast address address – set the multicast ip address to which multicast rtp packets are sent. The allowed range is 239.0.0.0 ~ 239.255.255.255. – set the ...

  • Page 50

    2n telekomunikace a.S., www.2n.Cz 50/76 vapix destination transport protocol – select the type of audio stream transmission: unsecured http or secured via ssl in https. – set the ip address to which rtp packets are sent. Address – set the destination port via which the device listens. Port – set the...

  • Page 51

    2n telekomunikace a.S., www.2n.Cz 51/76 3.1.7 action scheduler the menu includes 12 defined actions. Just use the switch to enable/disable the action. If the switch is inactive for an action, the action settings are not used. An action is generated supposing that it is activated and all the set cond...

  • Page 52

    2n telekomunikace a.S., www.2n.Cz 52/76 – activate/deactivate an action: on or off. The default value is off. State – add the name of the action to be generated, up to 20 characters. Name – add a description of the action to be generated, up to 60 description characters. – set the date from which th...

  • Page 53

    2n telekomunikace a.S., www.2n.Cz 53/76 3.1.8 system configuration account user name – set the user name for web login. 2n sip mic ® default user: admin – set the password for web login. Password 2n sip mic ® default password: 2n we strongly recommend you to change the password upon your first login...

  • Page 54

    2n telekomunikace a.S., www.2n.Cz 54/76 date and time use ntp server – use the ntp server for internal time synchronisation with 2n ® . Enable the function to deactivate the manual local time setting. Sip mic – set the ntp server ip address to be used for ntp server 2n sip mic ® internal time synchr...

  • Page 55

    2n telekomunikace a.S., www.2n.Cz 55/76 maintenance this section only describes the action buttons that generate direct actions to be confirmed using a dialogue window. Device reboot – restart . The entire restart process takes about 30 s. 2n sip mic ® once obtains the ip address after restart, the ...

  • Page 56

    2n telekomunikace a.S., www.2n.Cz 56/76 3.1.9 voice messages this menu includes a survey of 14 user message positions in the device for zone announcements. You can load messages in files, play pre-defined messages or remove messages from the device. You can arrange the rows from a to z or vice versa...

  • Page 57

    2n telekomunikace a.S., www.2n.Cz 57/76 system messages – set the message serial number: 1–2. Number – add the message name. The system message names are fixed and name invariable. 1 – announcement before voice message 2 – announcement after voice message – open a dialogue window to select the path ...

  • Page 58

    2n telekomunikace a.S., www.2n.Cz 58/76 3.2 setting examples the following subsections provide examples of the settings. The simplest 2n sip mic ® examples are always chosen, so some functions can be neglected for simplification. Refer to the configuration subsections for full details. 3.2.1 express...

  • Page 59

    2n telekomunikace a.S., www.2n.Cz 59/76 3.2.1 express settings the steps below describe how to set a new device quickly for announcing 2n ® sip mic to a multicast zone via a microphone. This is what you need for operation: 2n ® sip mic microphone supply adapter utp cable with poe for lan connection ...

  • Page 60

    2n telekomunikace a.S., www.2n.Cz 60/76 having found the ip address, open any web browser on a pc connected to the same network. Enter http://found_ip_address/ into the address row. Confirm your selection. If is connected in the right network, its 2n ® sip mic configuration web page opens up. Log in...

  • Page 61

    2n telekomunikace a.S., www.2n.Cz 61/76 select the zone name and description. Always choose multicast address as the destination type. Enter the future multicast address into the address field. Doing this, remember to use the allowed address range: 239.0.0.0 to 239.255.255.255. Complete the address ...

  • Page 62

    2n telekomunikace a.S., www.2n.Cz 62/76 3.2.2 announce to zone – vapix vapix announcing is similar to multicast announcing. The difference is that vapix plays announcements to one device only. It is a proprietary protocol, which enables an rtp stream to be sent to the set address. The advantage is t...

  • Page 63

    2n telekomunikace a.S., www.2n.Cz 63/76 select the zone name and description. Choose vapix destination as the destination type. There are two transport protocol options: http or https. Choose http for simplicity as some additional changes have to be done for https. Add the speaker ip address into th...

  • Page 64

    2n telekomunikace a.S., www.2n.Cz 64/76 once you save the changes, you can select https as the transport protocol in the 2n ® settings. Refer to step 4 in the preceding subsection. Sip mic.

  • Page 65

    2n telekomunikace a.S., www.2n.Cz 65/76 3.2.3 voice message loading there are two ways how to load a voice message to . You can either add 2n sip mic ® your audio file to the voice messages menu via a web browser. Or, you can load a message via a microphone or line in. In both the cases, you need a ...

  • Page 66

    2n telekomunikace a.S., www.2n.Cz 66/76 note once loading starts, the original audio message is deleted irreversibly. The maximum length of the audio message to be loaded is 60 s. A microphone attached to the front panel is used as the default sound source. If unattached, connect a microphone to the...

  • Page 67

    2n telekomunikace a.S., www.2n.Cz 67/76 3.2.4 http request set the http request to open the door, activate the network relay or send commands to other devices via the console. See the example below showing how to 2n sip mic ® set the switch activating http command. 2n helios ip verso ® suppose there...

  • Page 68

    2n telekomunikace a.S., www.2n.Cz 68/76 software 2n helios ip network scanner 3.0.4 ®.

  • Page 69

    2n telekomunikace a.S., www.2n.Cz 69/76 mechanical and electrical parameters dimensions: 209 x 142 x 65 mm weight: 1.600 g external power supply: 12 – 32 v dc / 1 a lan supply: poe ieee 802.3af lan connection: rj-45 connector on back panel, 10/100base-tx with auto- mdix function status signalling: s...

  • Page 70

    2n telekomunikace a.S., www.2n.Cz 70/76 5. Supplementary information here is what you can find in this section: 5.1 troubleshooting 5.2 directives, laws and regulations 5.3 general instructions and cautions.

  • Page 71

    2n telekomunikace a.S., www.2n.Cz 71/76 5.1 troubleshooting for the most frequently asked questions refer to . Faq.2n.Cz.

  • Page 72

    2n telekomunikace a.S., www.2n.Cz 72/76 5.2 directives, laws and regulations europe 2n sip mic ® conforms to the following directives and regulations: directive 1999/5/ec of the european parliament and of the council, of 9 march 1999 - on radio equipment and telecommunications terminal equipment and...

  • Page 73

    2n telekomunikace a.S., www.2n.Cz 73/76 this equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in...

  • Page 74

    2n telekomunikace a.S., www.2n.Cz 74/76 5.3 general instructions and cautions please read this user manual carefully before using the product. Follow all instructions and recommendations included herein. Any use of the product that is in contradiction with the instructions provided herein may result...

  • Page 75

    2n telekomunikace a.S., www.2n.Cz 75/76 the consumer shall, without delay, change the access password for the product after installation. The manufacturer shall not be held liable or responsible for any damage incurred by the consumer in connection with the use of the original password. The manufact...

  • Page 76

    2n telekomunikace a.S., www.2n.Cz 76/76 2n telekomunikace a.S. Modřanská 621, 143 01 prague 4, czech republic phone: +420 261 301 500, fax: +420 261 301 599 e-mail: sales@2n.Cz web: www.2n.Cz v1.0