1. DL manuals
  2. 2SAN
  3. DVR
  4. ADR-7616SW
  5. User Manual

2SAN ADR-7616SW User Manual

Manual is about: 2SAN 16CH H.264 Standalone DVR

Summary of ADR-7616SW

  • Page 1

    User manual version 1.0 16ch h.264 standalone dvr adr-7616sw.

  • Page 3: Statement

    Statement the information of the product in this manual is subject to change without prior notice and does not represent a commitment on the part of vendor, who assumes no liability or responsibility for any errors that may appear in this manual. This manual contains materials protected under intern...

  • Page 4: Table Of Contents

    Table of contents section1 introduction...........................................................................................................................5 1.1 product overview.......................................................................................................................

  • Page 5: Section1 Introduction

    Section1 introduction 1.1 product overview designed for globally increasing surveillance requirements, adr-7616sw is a high performance 16ch standalone digital video recorder. It takes h.264 compression format to not only improve video quality but also extend recording time over the same hard disk c...

  • Page 6

    Fps 120fps(d1), 240fps(half-d1), 480fps(cif) mode manual, schedule, alarm, motion, event, always playback fps 120fps(d1), 240fps(half-d1), 480fps(cif) storage internal hdd support sata hdd*2(3.5”) hot swap module option external esata port*1 backup usb 2.0 port 2 (for usb 2.0 drive, dvd-rw & usb mou...

  • Page 7

    Section2 system appearance & installation 2.1 front panel 1. Channel selection buttons number buttons can be used to display given channel on monitor and input password. 2. Function buttons a) func this button is reserved for future use. B) lock in order for only authorized person to operate buttons...

  • Page 8

    After system setting in menu, this button is used to save the settings and escape to upper menu. 3. Direction buttons and enter button a) direction buttons are used to move left, right, up and down in menu. B) enter button is used to select parameter in the menu. And in playback, it is used to selec...

  • Page 9

    2.2 rear panel 1. 16ch video inputs 16 channel composite video inputs with bnc connectors. Note:ntsc and pal video sources for 16ch video inputs can not be mixed. If they are mixed, dvr can’ not be operated properly. 2. 16ch loop through outputs 16 channel composite video outputs with bnc connectors...

  • Page 10

    8. Fan system fan. 9. Power input (from adapter) connect the adapter to the dvr for dc power supply.(dc19v / 7a). 10

  • Page 11

    2.3 hdd installation 1. Loosen each of the 11 screws on the front and back panels of the case with a screw driver to remove the cover. 2. Once you remove the cover on top of the dvr, unscrew the screws of the hard drive tray (2 on each side), and unplug the corresponding power cable and data cable a...

  • Page 12

    5. After installing the hard drive, if there’s a need to install a dvd-rom drive, please first remove the cf card slot, then remove the dvd-rom frame and remove the front baffle; finally, fix the dvd-rom onto the frame, as shown in the following steps: 6. Insert the frame with the dvd-rom installed ...

  • Page 13

    7. Finally, confirm that all the cables and screws are installed properly, then cover the lid and tighten it with the screws. 13.

  • Page 14: Section3 Menu

    Section3 menu 3.1 menu display no. Icon description 1 time system time/ date setup 2 record recording parameters setup 3 schedule weekly recording schedule setup for schedule recording mode 4 motion motion area/ sensitivity setup for motion recording mode 5 alarm alarm input type selection and buzze...

  • Page 15

    3.2 menu tree 1.Time 1.1 date setup 1.2 time setup 1.3 data display format 1.4 time display format 1.5 time zone setup 1.6 daylight saving 2.Record 2.1 resolution 2.2 fps 2.3 quality 2.4 record mode 2.5 post record 2.6 live audio 3.Schedule 4.Motion 4.1 motion ch 4.1 sensitivity 4.3 detection area 5...

  • Page 16

    7.1.4 system info 7.1.5 event log 7.1.6 firmware update 7.1.7 setting import/ export 7.1.8 user management 7.1.9 perercord 7.1.10 dvr number 7.2 display 7.2.1 camera title display 7.2.2 recode mode display 7.2.3 auto-hide toolbar 7.2.4 dwell 7.2.5 date time position 7.2.6 vga monitor ratio 7.2.7 rec...

  • Page 17: Section4 Menu S

    Section4 menu s etup for the first time using your dvr, you will want to establish the initial settings. This includes setting items such as time and date, record parameters, network and so on. In order to enter main menu for setup, first press menu button of the front panel in dvr. Note: password i...

  • Page 18

    4.1 time to access time setup, press enter button after moving highlight icon to time icon in menu. Time setup menu will appear on monitor shown as below. 1) date: move highlight icon to date in the time setup menu by using up or down button. Year, month and date can be changed after pressing enter ...

  • Page 19

    3) date display format: yy/mm/dd, mm/dd/yy, dd/mm/yy move highlight icon to date display format in the time setup menu by using up or down button. Date display format can be changed after pressing enter button. Use up or down and enter to select the parameter. 4) time display format: 12 hour, 24hour...

  • Page 20

    4.2 record to access record setup, press enter button after moving highlight icon to record icon in menu. Record setup menu will appear on monitor. 1) resolution: cif, half-d1, d1 in the record setup menu, move to the cell of resolution and ch which is to be setup using direction (up/ down/ left/ ri...

  • Page 21

    Record mode icon description manual if manual mode is set, the channel would start recording only by pressing the rec/stop button on front panel. Always if always mode is set, the channel would start recording after system power on. Motion if motion mode is set, the channel would start recording whi...

  • Page 22

    4.3 schedule to access schedule setup, press enter button after moving highlight icon to schedule icon in menu. Schedule setup menu will appear on monitor. When the record mode in record setup is set as schedule mode, the dvr will use the weekly schedule defined here to control the recording functio...

  • Page 23

    4.4 motion to access motion setup, press enter button after moving highlight icon to motion icon in menu. Motion setup menu will appear on monitor. 1) motion ch: to select the ch in which motion detection sensitivity and area would be set. 2) sensitivity: level 0 ~ 16 move highlight icon to date dis...

  • Page 24

    4.5 alarm to access alarm setup, press enter button after moving highlight icon to alarm icon in menu. Alarm setup menu will appear on monitor. 4.5.1 alarm input move highlight icon to alarm input in the alarm setup menu by using up or down button. Alarm input type setup menu will appear after press...

  • Page 25

    4.5.3 alarm output 2 the “alarm output” can be set to on or off. When it is on, once the “alarm in” is triggered, it will activate the “alarm out” in response. When it is off, then the “alarm out” won’t be activated while “alarm in” is triggered. 4.5.4 buzzer move highlight icon to buzzer in the ala...

  • Page 26

    4.5.5 email notification email notification; which can be set to on or off. When it is on, the network will add an “email setting” option for user making e-mail settings. 26.

  • Page 27

    4.6 network to access network setup, press enter button after moving highlight icon to network icon in menu. Network setup menu will appear on monitor. 1) ip mode: dynamic, static, pppoe move highlight icon to ip mode in the network setup menu by using up or down button. Ip mode can be changed after...

  • Page 28

    6) network: when the network setting is on, the network function will be activated. When the setting is off, the network function will be terminated. 7) ddns: move highlight icon to ddns in the network setup menu by using up or down button. Ddns function key: activates or deactivates the ddns functi...

  • Page 29

    Or with the mouse. After inputing the right username and password, press save & esc to save it. 9) email setting move highlight icon to email setting in the network setup menu by using up or down button. Email setting can be set after pressing enter button. Osd will appear a small keyboard, which ca...

  • Page 30

    10) streaming video resolution if the “streaming video resolution” is set as cif, the remote web browser will be showedat cif resolution. On the other hand, if the “streaming video resolution” is set as d1, theremote web browser will be showed at d1 resolution. Note: make the setting based on actual...

  • Page 31

    4.7 advanced to access advanced setup, press enter button after moving highlight icon to advanced icon in menu. Advanced setup menu will appear on monitor. 4.7.1 system move highlight icon to system in the advanced setup menu by using up or down button. System setup menu will appear after pressing e...

  • Page 32

    Button. Disk overwrite function can be set as on or off after pressing enter button. Use up or down and enter to turn on or off the disk overwrite function. If it is set as on, first recorded area in hdd can be replaced with new recording data, when recording hdd is full. 4) system info to show the ...

  • Page 33

    4.7.2 display move highlight icon to display in the advanced setup menu by using up or down button. Display setup menu will appear after pressing enter button. 1) camera title display: on, off to enables or disable the camera title display. 2) record mode display: on, off to enables or disable the d...

  • Page 34

    4.7.3 camera move highlight icon to camera in the advanced setup menu by using up or down button. Camera setup menu will appear after pressing enter button. 1) camera: ch1, ch2, ch3, ch4, ch5, ch6, ch7, ch8, ...Ch16 to choose the camera to be setup. 2) camera title: to assign a name for a camera. 3)...

  • Page 35

    1) ptz protocol: pelco-p, pelco-d if the channel corresponds to a ptz camera, setting the correct protocol allows control of the ptz camera. 2) ptz baudrate: 2400,4800,9600,19200,38400,115200 if the channel corresponds to a ptz camera, setting the correct baudrate allows control of the ptz camera. 3...

  • Page 36

    4.7.4 disk format move highlight icon to disk format in the advanced setup menu by using up or down button. Disk format menu will appear after pressing enter button. Use the up and down buttons to select the disk drive for disk format. Press the enter button and then use the up/down/enter to change ...

  • Page 37

    4.7.5 search & backup search & backup function here is used to search the history video data in dvr storage for playback or backup to other backup media. Move highlight icon to search & backup in the advanced setup menu by using up or down button. Search & backup menu will appear after pressing ente...

  • Page 38

    4) by event: provides a list of event recordings for user select to playback or backup. User can use mark function to select more than one file to backup. Note: press the number button in front panel identical to the number shown in each function button, and then each function button is selected and...

  • Page 39

    6) snapshot backup: use “up/down” moving to the snapshot backup option; press mark button. Select the photos to be backed up and press backup button to back them up; as graphically demonstrated in the picture below: 39.

  • Page 40

    4.7.6 account/ password note: this item would be shown on menu only when adminlock is set as on and can only be accessed by administrator and authorized users. (adminlock can be set as on or off in advanced >> system) move highlight icon to account/ password in the advanced setup menu by using up or...

  • Page 41: Section5 Live Display

    Section5 live display 1) display mode display modes, full picture, quad, 8split, 9-split, 16split are supported. Can be pressed for changing the display mode. A) full picture b) quad picture c) 8-split screen d) 9-split screen e) 16-split screen 41.

  • Page 42

    2) osd buttons for mouse input move the mouse cursor to the down side of monitor, the tool-bar would show up as below. Button description click on this button with the mouse cursor to enter the menu for dvr setup. Click on this button with the mouse cursor and the live display will change to the ful...

  • Page 43

    The audio sign will display on corresponding video channel only. Click on this button with the mouse cursor to take pictures of the current screen. When move the mouse to this area, it will show the remaining capacity of dvr hdd. 43.

  • Page 44: Section6 Backup

    Section6 backup the dvr supports usb 2.0 drive and dvd-rw(option) for video file backup, and please refer to 4.7.5 search & backup for the backup procedure. The backup file can be played via dvr file player software provided in the package. Section7 ptz control note: before using ptz, please make su...

  • Page 45: Section8 F/w Update

    Section8 f/w update step 1. Please copy the firmware file to the root directory of the cf card or usb drive, and then insert the cf card or usb drive into the cf slot or usb port on the front panel. Note: there are two firmware files: (1) autorun.Dat and (2) 76xxxxxx.Bin. Step 2. Now go into "menu /...

  • Page 46

    Section9 remote monitoring and control via ethernet the adr-7616sw dvr server can be remotely monitored or controlled via the ie or firefox browsers. Before using the remote monitoring and control function, make sure that the dvr is connected to the network and its ip address has be properly configu...

  • Page 47

    Step2. Enter your username and password. The default username and password are admin and 111111 respectively. Click on the login button to enter the main page shown as below: in this page user can make remote settings to the time, record, schedule, motion, alarm, network & advaced through network. 2...

  • Page 48

    3) record press record to make record-relevant setting, as graphically demonstrated in the picture below: after the setting is complete, press save&esc to return the main page. 4) schedule press schedule to make scheduled-record-relevant setting, as graphically demonstrated in the picture below: aft...

  • Page 49

    5) motion press motion to make scheduled-record-relevant setting, as graphically demonstrated in the picture below: after the setting is complete, press save&esc to return the main page. 6) alarm press alarm to make alarm-relevant setting, as graphically demonstrated in the picture below: after the ...

  • Page 50

    7) network press network to make network-relevant setting, as graphically demonstrated in the picture below: after setting is complete, press save&esc and the webpage will return to top page automatically; user now needs to re-input the username and password for new login. 8) advanced press advanced...

  • Page 51

    Upgrade the network firmware: press firmware update and system will jump to the following page automatically: follow the following steps to upgrade the network firmware: step1. Press the "browse" button to select the firmware file (ex: 7604h0136.Bin -please download the firmware from http://www.Acar...

  • Page 52

    After recording is stopped, system will prompt that the firmware uploading is successful; as shown in the following picture. Press ok to confirm it. Step 3: after complete, press ''pre-check'' to certify the firmware document; after the certification is complete, a prompt window will jump out statin...

  • Page 53

    Step5. After the prompt window of successfully burnt of firmware appears and “ok” is pressed, the firmware-updating procedure is complete; press “restart” to reboot the remote dvr unit. 9) live video monitoring use the full-screen, 4-split, buttons to switch different display mode for live monitorin...

  • Page 54

    Partition mode making live monitoring. 10) ptz control click on the ptz-control button at the top of the main page and a window displaying the settings for channel/ baud rate/ protocol will appear on the right of the screen. Enter the correct ptz camera parameters to enable the ptz control function....

  • Page 55

    9.2 web troubleshooting q1: after launching the browser and entering the dvr ip: port, the error "the page cannot be displayed" appears as shown below: a1: check the pc's network connection and the dvr network settings. Check that the ip address is correct and that the dvr is connected properly to t...

  • Page 56

    Appendix 1. Alarm input/output pin descriptions (16ch) pin no. Pin description 1 rs485- 2 rs485+ 3 com1 4 relay output n.O1 5 relay output n.C1 6 com2 7 relay output n.O2 8 relay output n.C2 9 sensor input 1 10 sensor input 2 11 gnd 12 sensor input 3 13 sensor input 4 14 gnd 15 sensor input 5 16 sen...

  • Page 57

    Pin no. Pin description 21 sensor input 9 22 sensor input10 23 gnd 24 sensor input11 25 sensor input12 26 gnd 27 sensor input13 28 sensor input14 29 gnd 30 sensor input15 31 sensor input16 32 gnd 57.

  • Page 58

    Appendix 2. Cf card compatible list brand capacity speed a-data 4gb 266x 8gb speedy apacer 4gb 300x hagiwara 4gb 300x kingston 1gb n/a 4gb 266x pertec 16gb 233x pqi 4gb 300x ridata 4gb 266x 8gb 233x 16gb 233x 32gb 133x sandisk 2gb n/a 4gb 266x transcend 2gb 266x 32gb 133x 58.

  • Page 59: Device

    Appendix 3. Play process after backing up dvr files to usb device (i)formatting in advance : reminder: if you wish to backup previous recorded historic data through the usb port, it is suggested to first format the usb device through the dvr in order to ensure that the usb device could be accurately...

  • Page 60

    (ii) when the formatting is complete, backup the recorded historic data : (1) insert the usb device into the usb port in front of the dvr. (2) enter menu => advanced => search & backup (3) when the usb device is properly inserted, the usb disk will appear in the backup to media column. (4) next, sel...

  • Page 61

    (5) then, using the "by channel & time" backup method as an example: select the “channel/start time/end time” you wish to backup, the backup file size will be displayed, and then press the “yes” button to start backing up. (6) when the backup is complete, a prompt will be displayed, as shown in the ...

  • Page 62

    (Ⅲ Ⅲ Ⅲ Ⅲ) when the backup is complete, files should exist in the usb device: (1) when the backup is complete, which files should exist? 1. Dvrplayer.Exe => the dvr's own playback program after the backup is complete; able to play back the following two formats: nongeneric (*.Dat dedicated format fil...