- DL manuals
- 3Com
- Webcam
- iCV-03a
- User Manual
3Com iCV-03a User Manual
Summary of iCV-03a
Page 1
Webcam user manual version 4.0 for models: icv-01a / icv-03a / icv-08.
Page 2: Contents
Contents chapter 1: introduction ________________________________________ 1 section 1. Features___________________________________________ 1 section 2. Webcam as a remote surveillance system ______________ 1 section 3. Package contents ___________________________________ 2 chapter 2: hardware instal...
Page 3
2.3.2 advanced (for password and http configuration) ____________ 56 2.5 about__________________________________________________ 58 2.6 refresh ________________________________________________ 58 chapter 6: multimonitor _______________________________________ 60 section 1. Installing multimonitor __...
Page 4: Chapter 1: Introduction
Chapter 1: introduction chapter 1: introduction section 1. Features webcam is a compact stand-alone web-server capable of remote video surveillance. It can be accessed from anywhere in the world via a standard browser by entering the ip address, account and password. Each system can support two type...
Page 5: Section 3. Package Contents
Chapter 1: introduction fig.1 webcam network diagram section 3. Package contents webcam package contain the following items; 1. Webcam server. 2. Usb camera. 3. Quick installation guide. 4. Utility cd containing; a. Utility: to configure ip address, update the firmware, etc. B. Multimonitor: to moni...
Page 6
Chapter 1: introduction fig.2 webcam front and back view led status indicators on webcam light color signal definition condition description green power state on: normal power red error condition flashing: error condition occurred orange logon state on: when there is user logon and receive the image...
Page 7
Chapter 2: hardware setup chapter 2: hardware installation the following details the hardware installation procedure for webcam ip camera. Step 1: connect the pc camera into the usb port of webcam. Step 2: connect the webcam to lan by using the ethernet utp port. Step 3: connect dc power adapter out...
Page 8: Chapter 3: Web Interface
Chapter 3: web interface chapter 3: web interface section 1. Introduction webcam is designed to work without having to install any software. All the necessary functions are built-into the unit. 1. Once you have finished the hardware setup shown in chapter 2, note down the ip address shown on the lcd...
Page 9
Chapter 3: web interface section 2. Using the web interface the webcam webpage main menu is divided into two sections. The selection menu on the left and display menu on the right. The selection menu consists of the following options: 2.1 view video 2.2 information 2.3 basic settings 2.4 advanced se...
Page 10
Chapter 3: web interface 2.1 to view video to view video from the connected camera, click on either activex or sun java. Choose either camera a or b to view the video. By default the first usb camera connected to webcam will be camera a note: activex can only function in windows platform and a plug-...
Page 11
Chapter 3: web interface once installed, the video will stream. Show current date & time click the record button to start video recording. The default directory is; c:\windows\temp\ the video will be saved in the following format; cmv20060710123058.Avi [cmv] [yyyy] [mm] [dd] [ttmmss].Avi to change t...
Page 12
Chapter 3: web interface to change video codec, click click save to confirm changes. Digital zoom in, digital zoom out rotate left, rotate right flip the image vertically. Hotspot icon. Each item corresponds to hotspot location set in basic setting patrol settings hotspot setting. Click to jump to t...
Page 13
Chapter 3: web interface using sun java controls: once you click on sun java the following pop-up window will appear. Click this to marquee an area and zoom into that area. Click this to reduce the image resolution. Click this to increase the image’s resolution. Click to digitally zoom in or out. Cl...
Page 14
Chapter 3: web interface this indicates the full pan-tilt range of the usb camera. This is the area and position the camera is currently showing. Webcam - user manual -11-.
Page 15
Chapter 3: web interface 2.2 information the information tab contains the following subsections; 2.2.1 system status, 2.2.2 current connections, and 2.2.3 event log. 2.2.1 system status this webpage displays all the information relating to webcam. This page is viewable by viewers of all permission l...
Page 16
Chapter 3: web interface 2.2.2 current connections fig.10 webcam current connections the current connections page shows all the users currently viewing either camera a or camera b (first icon denotes camera a). It also lists the login time and total bytes received. Note: administrator privilege is r...
Page 17
Chapter 3: web interface fig.12 webcam event log: administrator privilege. Fig.13 webcam event log: operator privilege. Webcam - user manual -14-.
Page 18
Chapter 3: web interface 2.3 basic settings the following option allows the user to customize their unit. 2.3.1 camera settings 2.3.2 patrol settings 2.3.3 network 2.3.4 account settings 2.3.1 camera settings use this section to set up the usb camera. I. Setting up camera a (or camera b) fig.14 indi...
Page 19
Chapter 3: web interface choose yes and webcam will increase the lighting of the image. This is useful when monitoring indoors. Choose no if you do not want webcam to compensate for bright indoor lighting and view the images as is. Color choose yes for color and no for black and white display. Black...
Page 20
Chapter 3: web interface this section allows the user to define hotspots, required patrol boundary, and see where the current camera position. Fig.15 webcam patrol setting / controls user defined pan tilt boundary maximum boundary (x,y) of the pan tilt camera click to select which camera to control....
Page 21
Chapter 3: web interface b. Square – the camera will patrol along the user defined boundary in a clock wise manner. C. Pan only – the camera will perform pan function only. D. Tilt only – the camera will perform tilt function only. E. In sequence (1-5) – the camera will jump to each hotspot location...
Page 22
Chapter 3: web interface fig.17 webcam dns server ip primary dns server ip this item sets webcam primary dns server ip address. This is the default dns and cannot be edited. Secondary dns server ip use this to set webcam secondary dns server ip address. Webcam will use the secondary dns server ip ad...
Page 23
Chapter 3: web interface each webcam unit is shipped with a default domain name ***.Icv99.Net, where *** is the unique 10 digit serial number located at the back of webcam. Fig.20 webcam default dynamic dns use default domain name each unit of webcam is shipped with a default domain name. To activat...
Page 24
Chapter 3: web interface 4. Once registered, user can change either, the default domain name, dns password or email address. Click confirm to save changes. Note: enter a valid email address. In the event you have forgotten the password to your dns account, a new password will be sent to this email a...
Page 25
Chapter 3: web interface ii. Other dynamic dns fig.21 dynamic dns from other service providers service provider in addition to http://ddns.Icv99.Net, webcam can be configured to register with other dynamic dns providers. The following free ddns service providers are supported; • dhs.Org • dyndns.Org...
Page 26
Chapter 3: web interface use public ip to register choose yes to ensure that webcam uses the wan / public ip to register with the selected ddns server. Iii. Pppoe use this option to allow webcam to connect to the internet directly using your xdsl modem. Once set-up, webcam will connect directly to t...
Page 27
Chapter 3: web interface user name assign a user name / account. The administrator can set up to 32 case sensitive character names. Password assign a password to the account. The administrator can set up to 32 case sensitive passwords. Permission this sets the access level to individual user account...
Page 28
Chapter 3: web interface fig.24 webcam permit hours configuration click configure to set the hours. The administrator can set up to 4 different permit hours (in 24hr format). Click apply to save. Click close to exit without saving. Note: the reset button only revert the fields to initial values prio...
Page 29
Chapter 3: web interface 2.4 advanced settings this section allows the administrator to set up some of the features available in the server. 2.4.1 event notification 2.4.2 motion detection 2.4.3 image recording 2.4.4 email / ftp 2.4.5 system settings 2.4.6 image server 2.4.7 language 2.4.8 about 2.4...
Page 30
Chapter 3: web interface the available email addresses are listed here. See section 2.4.4 on how to enter an email address to the address book. To add an email address click edit. Webcam will ask you to save your configuration prior to leaving this page. Recipients up to 8 valid email accounts can r...
Page 31
Chapter 3: web interface fig.27 event selection list note: the image recording and motion detection notification function here will only send an email notification without any picture attached. For email notification with images, the administrator has to setup the motion detection page (see section ...
Page 32
Chapter 3: web interface webcam will email the following notification depending on which event was selected. Fig.28 event notification: user login details (date, time, camera & ip) fig.29 event notification: camera a motion detected webcam - user manual -29-.
Page 33
Chapter 3: web interface fig.30 event notification: pppoe connect successful with public ip shown 2.4.2 motion detection this page allows the administrator to set motion detection functions for the cameras. I. Camera a (or camera b) fig.31 motion detection page enable the administrator has two optio...
Page 34
Chapter 3: web interface note: check that you have setup valid email / ftp accounts first before proceeding with the rest of the configuration. To setup email / ftp, see section 2.4.4 detection sensitivity this will determines the level of change before motion capture is triggered. A high percentage...
Page 35
Chapter 3: web interface loop from … to … this will determine the number of files in the sequence. Once the last file number is reached, it’ll loop and replace the first file in the sequence with the most current image. Digits … this will determine the number of digits assignable for the above seque...
Page 36
Chapter 3: web interface to remove a recipient from the list, click > to remove all the recipients from the list, click >> click apply to confirm and save the settings. 2.4.3 image recording image recording allows the user to receive a string of jpg images to either their email account or ftp accoun...
Page 37
Chapter 3: web interface fig.34 email of image recorded 2.4.4 e-mail / ftp this webpage sets up the necessary email and ftp server information. The administrator will have to enter a valid account name and password to the email server and/or ftp server. These information has to be setup in order for...
Page 38
Chapter 3: web interface i. Ftp settings fig.36 ftp settings ftp server the administrator will have to enter the full ftp server address here. Account name enter the ftp login account name here. Password enter the account password. Click apply to save the above settings. Ii. Email settings fig.37 em...
Page 39
Chapter 3: web interface iii. Sending test mail fig.38 sending a test mail a. Click test mail to check that the email setting has been correctly configured. Fig.39 saving configuration before sending a test mail b. Click yes to save configurations and proceed to the following window. Fig.40 test mai...
Page 40
Chapter 3: web interface fig.41 confirmation email the administrator can also check information event log for confirmation or failure. Fig.42 event log: test mail successful fig.43 event log: test mail failed iv. Email address book fig.44 e-mail address book entry enter an email address in the box p...
Page 41
Chapter 3: web interface fig.45 system settings page i. System time fig.46 system time system time updates the administrator can set an interval for time synchronization. Select either; 1, 3, 12 hours or 1, 10 & 30 days. Time server choose the nearest time server to your webcam location. The adminis...
Page 42
Chapter 3: web interface fig.47 add time server dialog box time zone (relative to gmt) select the appropriate time zone. Click apply to save changes. System time (yyyy/mm/dd hh:mm:ss) this section is to manually set webcam system time. The format is pre-determined to: yyyy/mm/dd hh:mm:ss (in 24hr fo...
Page 43
Chapter 3: web interface fig.50 snmp settings system name this is to give webcam a name identifiable in a snmp network. System contact this is to give the administrator an identity in the snmp network. System location this is to set webcam snmp location. Manager ip address this set the lan ip addres...
Page 44
Chapter 3: web interface fig.51 image server settings page enable choose yes to enable this feature or no to disable. Community this is a security feature. Set a community password to add an extra level of internet security to webcam. Community password is left blank by default. Click apply to confi...
Page 45
Chapter 3: web interface fig.52 image server login page fig.53 image account registration page 3. Once registered, a confirmation email will be sent to your email address. You can now sign in to your account using your new image user id. 4. Goto add / remove unit, and enter the serial number and com...
Page 46
Chapter 3: web interface unit added to my list 5. Next click return to my list, and and click on the “eye” icon to view the camera. Click on either opened “eye” icon to view the camera. Webcam - user manual -43-.
Page 47
Chapter 3: web interface 2.4.7 language use this section is to set webcam interface language. I. Interface language at the moment, the user can choose the following versions; a. Western version for; • english, • spanish, • french, • dutch, and • portuguese. B. Eastern version for; • english, • tradi...
Page 48
Chapter 3: web interface 2.4.8 about the administrator can use this section to check firmware information, save/restore settings, upgrade firmware and see manufacturer’s details. Fig.54 about page i. About this shows the firmware version, hardware version and serial number. Ii. Save / restore settin...
Page 49
Chapter 4: view images using pda / ppc / mobile chapter 4: view images using pda / ppc / mobile webcam supports image viewing from a grps / wifi enabled pda / ppc / symbian mobile device. To view the images; a. Make sure that the pda / ppc / mobile unit is connected to lan or internet. B. Enter http...
Page 50
Chapter 4: view images using pda / ppc / mobile e. The default file name is showimg_pda.Jpg, click save as… to change the file name or save location. Note: the downloaded image size depends on the resolution set in basic settings camera settings image size. Approximately; 6kb @ 320x240 vs. 17kb @ 64...
Page 51: Chapter 5: Using The Utility
Chapter 5: using the utility program chapter 5: using the utility section 1. Installation 1. Insert the enclosed utility cd into the cd-rom drive. The following menu will show up. Click on the buttons on the left to install the programs you want. Utility - this is a program that helps the user perfo...
Page 52
Chapter 5: using the utility program section 2. Using the utility program the utility main menu is shown below. The selection menu is located on the left. The serial number, current firmware and ip address of every webcam connected to the lan will be displayed on the table to the right. Fig.57 utili...
Page 53
Chapter 5: using the utility program 4. Enter the necessary camera configurations. Choose the appropriate frequency (indoor 60 hz, indoor 50 hz or outdoor) to prevent flickering on the video feed. Enter a name for the camera in the location: box to identify the camera. 5. Click next > to configure t...
Page 54
Chapter 5: using the utility program obtain an ip address by bootp choose this if you want to allow webcam to obtain an ip address using bootp protocol. 6. Click next > to proceed to xdsl/cable modem setup. Choose this if you want webcam to connect directly to your xdsl line. A. Select enable pppoe ...
Page 55
Chapter 5: using the utility program ddns service allows you to assign a domain name to your dynamic ip. This way, you will always be able to locate your device over the internet. (for more details see chapter 4, section 2.3.2, part v) 8. Click next > to change your administrator account and passwor...
Page 56
Chapter 5: using the utility program 2.2 launch webcam click launch webcam or double click the webcam listed in the table to launch it. Click either one to launch webcam camera. Webcam - user manual -53-.
Page 57
Chapter 5: using the utility program webcam login screen will appear. Click apply. Enter the account (login name) and password (login password) set earlier. Otherwise, use the default login and password at the back of webcam unit. If you did not configure one, then just click apply to login. Webcam ...
Page 58
Chapter 5: using the utility program 2.3 ip configuration this section allows you to configure the ip address for webcam. You do not have to edit this section if you have gone thru setup wizard earlier. Select the unit and then click ip configuration. Select the webcam unit on the right display scre...
Page 59
Chapter 5: using the utility program obtain an ip address by dhcp choose this if you want your router to assign an ip address to webcam. This is the default setting. Obtain an ip address by bootp choose this if you want to allow webcam to obtain an ip address using bootp protocol. Use the following ...
Page 60
Chapter 5: using the utility program once set, utility will request for the device password when you try to click on either, setup wizard, launch webcam or ip configuration button. To remove the password, if the devise password is enabled, the ip address will be hidden. No devise password set. A. Se...
Page 61
Chapter 5: using the utility program uncheck to disable this function. Example: if a value of say, 8080 is set as the http port number, then enter http://192.168.0.177:8080 in order to access webcam web interface. 2.5 upgrade firmware click this to bring up the upgrade firmware dialog box. To check ...
Page 62
Chapter 5: using the utility program the user can do a manual search by clicking the refresh. Webcam - user manual -59-.
Page 63: Chapter 6: Multimonitor
Chapter 6: multimonitor chapter 6: multimonitor multimonitor is a program to manage multiple webcam. It is able to detect the ip address of all webcam installed in lan and list them for easy management. Section 1. Installing multimonitor click on setup.Exe and follow the installation wizard after in...
Page 64
Chapter 6: multimonitor fill out the necessary information shown below and click next >. Webcam - user manual -61-.
Page 65
Chapter 6: multimonitor click finish and the multimonitor logon window below will pop up. Just click ok to start using multimonitor note: the default security logon name is admin, no password is set. To set a password, click user change password … new password webcam - user manual -62-.
Page 66
Chapter 6: multimonitor 2.1 device : start multimonitor and press the “enumerate” button, multimonitor will start a search for all the webcam units on the network and list them in the main window. Once detected, the following will show in the main window: this shows that the camera is online and act...
Page 67
Chapter 6: multimonitor : manually adds the webcam camera to be monitored. A. Access by webcam address host address: enter either the web address (without the www eg: webcam.Myddns.Com) or lan ip of webcam (eg: 192.168.0.30) remote port: this is webcam udp port. B. Access by image server image serve...
Page 68
Chapter 6: multimonitor : highlight the webcam to be deleted from multimonitor’s list. Click yes to confirm deletion. : use this function to change webcam ip address & port number. Webcam - user manual -65-.
Page 69
Chapter 6: multimonitor display the current camera settings. Camera select: select either camera a or b account: if you have setup user account, the information must be entered here. Otherwise access will be denied. Password: enter the above account password. Image zoom: resize the window to between...
Page 70
Chapter 6: multimonitor display the motion detection settings. Enable motion detect: click the checkbox to enable motion detection. Note: this feature requires the camera window be active to work. Click “monitor” to activate the window. Sensitivity: choose from 0% to 100% (very sensitive) window on-...
Page 71
Chapter 6: multimonitor image compression: choose from the list of available compressions. Note: this list is dependent on the codec that is available or already installed on the local pc. To record in mpec-4, make sure you install or upgrade to windows media player v10. Recording avi file path loca...
Page 72
Chapter 6: multimonitor configure settings for email notification you will need to enter the correct message sender information in order for webcam to send emails. Server require authentication click settings… then enter your account name and account password. Notified email address click add… and e...
Page 73
Chapter 6: multimonitor snmp settings host name: provide a name to identify this device. Http port: enter the http port assigned for webcam. Location: provide a location for snmp manager to track device. Manager: enter a manager’s name for identification. Using snmp to update network ports check thi...
Page 74
Chapter 6: multimonitor show the current date and time. Click to bring out zoom, resolution, direction and auto p/t controls. See below. Show current fps. Move the curser over the edges of the picture and it will turn into an arrow. Click and hold to pan / tilt the camera (if the camera supports thi...
Page 75
Chapter 6: multimonitor click on this icon to active two functions; a. Custom window zoom – use this to zoom to your chosen window size. On the video window, left click, hold and drag to the desired window zoom size. A thin line will outline the chosen window size. Window marquee tool. See below for...
Page 76
Chapter 6: multimonitor release and the program will zoom to the marquee area. Increase the resolution for a better image quality. While zoomed in, the user can digitally pan or tilt the camera window. Even if it is a static camera! Click the depressed button to go back to the original window size o...
Page 77
Chapter 6: multimonitor release to set the window frame. Video in this custom window will be updated while those outside are ‘frozen’. You can digitally pan and tilt the smaller window while in this state. Only video in the custom window will be updated. This feature works with static or pan tilt ca...
Page 78
Chapter 6: multimonitor : set the snmp parameter. 2.4 user change password change password … use this feature to change the user’s login password to imultiview. Either administrator or user can change their account passwords. Account management… use this section to add, delete or change the password...
Page 79
Chapter 6: multimonitor add user… there is no limit to the number of account that can be added. Note: the first account is set to administrator permission. This cannot be changed or deleted. Account: enter the preferred account name (max of 10 characters). The account name cannot be edited. Password...
Page 80
Chapter 6: multimonitor 2.6 drag-and-drop feature multimonitor feature a “drag-and-drop to desktop” function. Double click the icon on your desktop to immediately view the video. Useful when monitoring multiple cameras at a time. Step 1: select the camera location of your choice. Step 2: left click,...
Page 81
Chapter 6: multimonitor step 4: double click on the icon on the desktop, to view the images. Webcam - user manual -78-.
Page 82
Appendix a: router configuration appendix a: router configuration the following section describes the initial configuration of the router and port forwarding for your router. If your router is not listed here, please refer to the manufacturer’s website for assistance with configuring your router to ...
Page 83
Appendix a: router configuration mn-500 wireless base station netgear rp614 web safe router mr814 wireless router mr314 cable/dsl wireless router fvs318 prosafe vpn firewall proxim orinoco bg-2000 broadband gateway - siemens speedstream 2602 2-port dsl/cable router speedstream 2623 wireless dsl/cabl...
Page 84
Appendix a: router configuration 3com (http://www.3com.Com) 3c857-us – officeconnect cable/dsl gateway 3crwe52196 – officeconnect wireless cable/dsl gateway 1. Log into your router using your router ip. 2. On the main page, select firewalls on the left side of the page. 3. Select the virtual servers...
Page 85
Appendix a: router configuration belkin (http://www.Belkin.Com) f5d6230-3 – wireless cable/dsl gateway router 1. Log into your router using your router ip. 2. On the main page, select virtual server on the left side of the page under the securit section. 3. Enter the following information on the pag...
Page 86
Appendix a: router configuration private port 80 to 80 line #2 enable: checked in description: webcam – camera internet port: 9001 to 9001 type: udp private ip address: type in the camera’s ip address. (look on the webcam address lcd display for the last 3 digits of the camera’s ip address) private ...
Page 87
Appendix a: router configuration d-link (http://www.Dlink.Com) di-604/di – 614+/di-624 1. Log into your router using your router ip. 2. On the main page, click on advanced at the top of the page. 3. On the left side of the page, click on virtual server. Note: make sure dmz host is disabled. If dmz i...
Page 88
Appendix a: router configuration enabled/disabled: enabled for id#2 service port: 9001 service ip: type in the camera’s ip address, for example: 192.168.0.5 enabled/disabled: enabled 4. Save your settings. Webcam should now be configured to work with your router and be accessible from the internet. ...
Page 89
Appendix a: router configuration dell (http://www.Dell.Com) truemobile 2300 wireless broadband router 1. Log into your router using your router ip. 2. On the main page, click on advanced settings at the top of the page. 3. Go to the port forwarding section and select custom port forwarding settings....
Page 90
Appendix a: router configuration linksys (http://www.Linksys.Com) befsr41 – etherfast cable/dsl router befsx41 – instant broadband etherfast cable/dsl firewall router with 4-port switch/vpn endpoint befw11s4 – wireless access point router with 4-port switch – version 2 1. Log into your router using ...
Page 91
Appendix a: router configuration microsoft (http://www.Microsoft.Com/hardware/broadbandnetworking) mn-100 – wired base station mn-500 – wireless base station 1. Log into your router using your router ip. 2. Open the bass station management tool, and then click security. 3. On the security menu, clic...
Page 92
Appendix a: router configuration netgear (http://www.Netgear.Com) rp614 – web safe router mr814 – wireless router 1. Log into your router using your router ip. 2. Click advanced -> port forwarding on the left side of the page. 3. Click add customer service. 4. Enter the following information on the ...
Page 93
Appendix a: router configuration line #2: starting port: 9001 ending port: 9001 server ip address: type in the camera’s ip address, for example: 192.168.0.5 5. Click apply to save the settings. Webcam should now be configured to work with your router and be accessible from the internet. Fvs318 – pro...
Page 94
Appendix a: router configuration d. Local server address: enter the ip address of the camera e. Wan users address: any f. Click apply. 12. Click add again. A. For service name select: webcam cam b. Action: allow always c. Local server address: enter the ip address of the camera d. Wan users address:...
Page 95
Appendix a: router configuration proxim (http://www.Proxim.Com) orinoco bg-2000 broadband gateway 1. Log into your router using your router ip. 2. On the router’s main page, click on setup at the top of the page. 3. On the left side of the page, click on advanced settings -> port forwarding. 4. Chec...
Page 96
Appendix a: router configuration siemens (http://www.Speedstream.Com) speedstream 2602 – 2-port dsl/cable router speedstream 2623 – wireless dsl/cable router speedstream 2624 – wireless dsl/cable router 1. Log into your router using your router ip. 2. After you are logged in, click on advanced setup...
Page 97
Appendix a: router configuration 7. Under internal port no type in: 80 8. Under external port no type in: 80 9. Click on add to save these settings. 10. Under the first box, next to the enable checkbox, type in: webcam cam. 11. Under pc (server), select your camera or the camera’s ip address from th...
Page 98
Appendix a: router configuration smc (http://www.Smc.Com) smc2404wbr – barricada turbo 11/22 mbps wireless cable/dsl broadband router smc7004vbr – barricada cable/dsl broadband router smc7004cwbr – barricada wireless cable/dsl broadband router 1. Log into your router using your router ip. 2. After y...
Page 99
Appendix a: router configuration for id #2: service port: 9001 private ip: type in the camera’s ip address, for example: 192.168.0.5 (look at webcam’s ip address lcd display for the last 3 digits of the camera’s ip address) enable: checked in 4. Click save to save the settings. Webcam should now be ...
Page 100
Appendix b: methods to update webcam firmware appendix b: methods to update webcam firmware you can update webcam firmware using any of the following methods. Method 1: through webcam web page (1) enter the webcam web page (2) go to “about”, click “update software” and you will be automatically link...
Page 101
Appendix c: ip address, subnet and gateway appendix c: ip address, subnet and gateway this section discusses communities, gateways, ip addresses and subnet masking communities a community is a string of printable ascii characters that identifies a user group with the same access privileges. For exam...
Page 102
Appendix c: ip address, subnet and gateway subnetting and subnet masks subnetting divides a network address into sub-network addresses to accommodate more than one physical network on a logical network. For example: a class b company has 100 lans (local area networks) with 100 to 200 nodes on each l...
Page 103: Appendix D: Glossary
Appendix d: glossary appendix d: glossary the glossary section defines the terms used in this user manual term definition ethernet local area network technology, originally developed by xerox corporation, can link up to 1,024 nodes in a bus network. Ethernet provides raw data transfer in a rate of 1...