3Com Powerware Prestige Series Installation And Operator's Manual

Manual is about: 3000 VA, 200-240V

Summary of Powerware Prestige Series

  • Page 1

    Powerware ® prestige series 3000 va, 200-240v installation and operator’s manual for ibm applications.

  • Page 2: Class A Emc Statements

    Requesting a declaration of conformity units that are labeled with a ce mark comply with the following harmonic standards and eu directives: : harmonic standards: en 50091-1-1 and en 50091-2 : eu directives: 73/23/eec, council directive on equipment designed for use within certain voltage limits 93/...

  • Page 3: Uick

    Q uick i nstall ups with ppdm quick installation 1 if you are connecting the ups to an as/400, the qupsdlytim system value for the ups monitoring feature should be set. See “ups monitoring” on page 52 for instructions. 2 battery cabinet ups cabinet powerpass distribution module (ppdm,) 3 bypass swit...

  • Page 4

    Quick install 4 21 battery breaker i o on off i o on off , 5 6 the ups output voltage is factory-configured for 230v. If you need to change the output voltage, see “ups with ppdm startup” on page 42. 7 for the as/400 interface, plug the as/400 communications cable into the serial port on the ups rea...

  • Page 5: Able Of

    I powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy t able of c ontents 1 introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ups model and battery configurations 2 . . . ...

  • Page 6: 6 Specifications

    Table of contents ii powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ups communications interface port 64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communications mode reference char...

  • Page 7: Ntroduction

    1 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy c h a p t e r 1 i ntroduction congratulations on the purchase of your powerware 9 prestige series uninterruptible power system (ups). The prestige ups meets the toughest measures of supe...

  • Page 8: Load Requirements

    Introduction 2 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ups model and battery configurations this ups is designed to work with single-phase, three-wire, ac power sources. There are two important considerations when selecting the ...

  • Page 9: Approximate Battery Times

    Introduction 3 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 3 computers 3 monitors external modem 3 x 200 watts x 1.4 = 840 va 3 x 1 amp x 240 = 720 va 50 va 840 va + 720 va + 50 va = 1610 va (total load requirements) 200 watts each ...

  • Page 10: Prestige 3000 With Ppdm

    Introduction 4 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 1. See “load requirements” on page 2 for assistance in determining the total load requirements for your ups. Round this number up to the next load (va) entry in the followin...

  • Page 11: Special Symbols

    Introduction 5 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy special symbols the following common symbols may be found on the ups: load on - press the button with this symbol to energize the output receptacles (output on). Load off - ...

  • Page 12

    Introduction 6 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy this page intentionally left blank..

  • Page 13: Afety

    7 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy c h a p t e r 2 s afety w arnings i m p o r t a n t s a f e t y i n s t r u c t i o n s save these instructions. This manual contains important instructions that you should follow during...

  • Page 14: Sikkerhedsanvisninger

    Safety warnings 8 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : to comply with international standards and wiring regulations, the total equipment connected to the output of this ups must not have an earth leakage current greater th...

  • Page 15

    Safety warnings 9 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : batterierne bør aldrig åbnes eller skilles ad. Elektrolyt, der slipper ud, er skadelig for hud og øjne og kan være overordentlig giftig. : brug kun den netledning, som ...

  • Page 16: Bewaar Deze Instructies

    Safety warnings 10 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy belangrijke veiligheidsinstructies belangrijke veiligheidsinstructies bewaar deze instructies deze handleiding bevat belangrijke veiligheidsinstructies g e v a a r deze ...

  • Page 17: Tärkeitä Turvaohjeita

    Safety warnings 11 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : verwijder de ingangsnoer niet of haal de stekker van de ingangsnoer er niet uit terwijl de ups aan staat. Hierdoor zou de ups en uw aangesloten apparatuur geen aardebe...

  • Page 18

    Safety warnings 12 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : tämä ups sisältää oman energialähteen (akuston). Ulostuloliittimissä voi olla jännite, kun ups ei ole liitettynä verkkojännitteeseen. : Älä koskaan heitä akkuja tuleen...

  • Page 19: Consignes De Sécurité

    Safety warnings 13 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy consignes de sécurité consignes de sÉcuritÉ importantes conserver ces instructions ce manuel contient des consignes de sÉcuritÉ importantes d a n g e r ! Cet onduleur co...

  • Page 20: Sicherheitswarnungen

    Safety warnings 14 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : ne pas retirer le cordon d’alimentation lorsque l’onduleur est sous tension sous peine de supprimer la mise à la terre de l’onduleur et du matériel connecté. : afin d’...

  • Page 21

    Safety warnings 15 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : diese usv ist mit einer eigenen energiequelle (batterie) ausgestattet. An den ausgangssteckdosen kann auch dann spannung anliegen, wenn die usv nicht an einer wechsels...

  • Page 22

    Safety warnings 16 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : für bypass-systeme mit festverdrahteten eingängen muß der Überstromschutz für die ausgangswechselstromkreise anderweitig bereitgestellt werden. : für bypass-systeme mi...

  • Page 23

    Safety warnings 17 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : ×ñçóéìïðïéåßôå ìüíï ôï êáëþäéï ôñïöïäïóßáò ðïõ ðáñÝ÷åôáé ìáæß ìå ôï ups. Ôï êáëþäéï áõôü åßíáé êáôáóêåõáóìÝíï óýìöùíá ìå ôéò ðñïäéáãñáöÝò ôïõ Åèíéêïý Çëåêôñéêïý Êþäéêá...

  • Page 24: Avvisi Di Sicurezza

    Safety warnings 18 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy avvisi di sicurezza importanti istruzioni di sicurezza conservare queste istruzioni questo manuale contiene importanti istruzioni di sicurezza p e r i c o l o la tension...

  • Page 25

    Safety warnings 19 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : per ridurre il rischio di incendio o di scossa elettrica, installare il gruppo statico di continuità in un ambiente interno a temperatura ed umidità controllata, privo...

  • Page 26: F A R L I G

    Safety warnings 20 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy viktig sikkerhetsinformasion f a r l i g denne ups’en inneholder livsfarlige spenninger. All reparasjon og service må kun utføres av autorisert servicepersonale. Brukere...

  • Page 28

    Safety warnings 22 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : utilize somente o cabo de alimentação elétrica fornecido com a ups. Este cabo foi fabricado de acordo com as especificações do iec (international electrical code). Cer...

  • Page 29: О П А С Н О

    Safety warnings 23 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy Предупреждения по мерам безопасности ВАЖНЫЕ УКАЗАНИЯ ПО МЕРАМ БЕЗОПАСНОСТИ СОХРАНИТЕ ЭТИ УКАЗАНИЯ ДАННОЕ РУКОВОДСТВО СОДЕРЖИТ ВАЖНЫЕ УКАЗАНИЯ ПО МЕРАМ БЕЗОПАСНОСТИ О П А...

  • Page 30

    Safety warnings 24 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : Для снижения опасности пожара или поражения электрическим током устанавливайте ИБП в закрытом помещении с контролируемыми температурой и влажностью, в котором отсутств...

  • Page 31: Advertencias De Seguridad

    Safety warnings 25 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy advertencias de seguridad instrucciones de seguridad importantes guarde estas instrucciones este manual contiene instrucciones de seguridad importantes p e l i g r o est...

  • Page 32: Säkerhetsföreskrifter

    Safety warnings 26 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : no retire o desenchufe el cable de entrada mientras el sie se encuentre encendido. Esto suprime la descarga a tierra de seguridad del sie y de los equipos conectados a...

  • Page 33

    Safety warnings 27 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy : denna ups-enhet har en egen energikälla (batterier). De utgående kontakterna kan vara strömförande när ups-enheten inte är ansluten till en växelströmkälla. : använda ...

  • Page 34

    Safety warnings 28 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy.

  • Page 35

    Safety warnings 29 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy.

  • Page 36

    Safety warnings 30 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy.

  • Page 37

    Safety warnings 31 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy.

  • Page 38

    Safety warnings 32 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy.

  • Page 39

    Safety warnings 33 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy.

  • Page 40

    Safety warnings 34 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy this page intentionally left blank..

  • Page 41: Nstallation

    35 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy c h a p t e r 3 i nstallation the following sections describe ups storage requirements and the installation and startup of the ups. Unpacking and inspection carefully unpack the ups and...

  • Page 42

    Installation 36 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy use the following procedure to install the ups and battery cabinets with the ppdm: 1. Place the ups near the equipment to be protected. The ups should be well ventilated an...

  • Page 43

    Installation 37 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ppdm power output receptacles (5-15r) utility input connector ups cabinet breaker tie circuit breaker battery cabinet external battery connector battery cord bypass switch ...

  • Page 44

    Installation 38 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ppdm neutral ground screw utility input connector (iec 320-c13) ups cabinet breaker tie circuit breaker battery cabinet external battery connector battery cord bypass switc...

  • Page 45

    Installation 39 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy for ungrounded output neutral applications only. Remove the ground screw, rotate the ground cover until it snaps into place, and reinstall the ground screw in the ungrounde...

  • Page 46

    Installation 40 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 12. For the as/400 interface, plug the as/400 communications cable into the serial port on the ups rear panel. Plug the other end of the cable into the j14 connector or the...

  • Page 47

    Installation 41 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ups cabinet breaker tie circuit breaker battery cabinet external battery connector battery cord input circuit protector battery connector power output receptacle power inpu...

  • Page 48: Ups With Ppdm Startup

    Installation 42 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ups with ppdm startup to start up the ups: 1. If you are connecting the ups to an as/400, the qupsdlytim system value for the ups monitoring feature should be set. See “ups...

  • Page 49

    Installation 43 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 4. Plug the input power supply cord (use the as/400 or ppdm line cord) into the utility input connector on the ppdm rear panel. Press and hold the output off button while p...

  • Page 50: Repo Installation

    Installation 44 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 10. Turn on the equipment that is connected to the ups. 11. Press and hold the output on button until you hear the ups beep (approximately one second). The indicator remain...

  • Page 51

    Installation 45 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 1. Place the conduit through the access hole on the junction box (see figure 10). Connect the exposed conduit wires to the corresponding compression terminals (see the foll...

  • Page 52: Troubleshooting Tips

    Installation 46 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy troubleshooting tips if you should encounter any problems during startup, see the troubleshooting chart on page 71. The battery cabinets are shipped with the batteries char...

  • Page 53: Ups O

    47 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy c h a p t e r 4 ups o peration this chapter covers the operation of the ups including front panel functions, operating modes, using the battery start feature, shutting down the ups, and...

  • Page 54: Operating Modes

    Ups operation 48 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy operating modes after you install and apply power to the ups, the ups filters and regulates incoming ac power, eliminating noise and voltage spikes, and provides consisten...

  • Page 55: Bypass Mode

    Ups operation 49 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy bypass mode the indicator and the indicator illuminate simultaneously, indicating bypass mode (see figure 14). When the ups is in bypass mode, the load is powered by utili...

  • Page 56: Diagnostics

    Ups operation 50 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy when shutdown is imminent, the self test indicator flashes. These warnings are approximate, and the actual time to shutdown may vary significantly. For approximate battery...

  • Page 57: Ups Shutdown

    Ups operation 51 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy the ups supplies power to your equipment and goes into battery mode. The indicator remains lit and the front panel displays the percentage of battery capacity remaining to...

  • Page 58: Ups Monitoring

    Ups operation 52 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ups monitoring ups monitoring is a standard feature of the as/400 operating system. Qupsdlytim is a timer in the as/400 that tells the system how long to run on ups power ...

  • Page 59: Using The Ppdm

    Ups operation 53 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy using the ppdm the ppdm provides continuous online power for your equipment. With the ppdm, you can replace or upgrade the ups without losing power to your equipment. Figu...

  • Page 60

    Ups operation 54 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 4. Switch the circuit breaker on all battery cabinets to the off (o) position. 5. Disconnect the battery connector on the ups rear panel. 6. Remove the ups. Ppdm ups cabin...

  • Page 61: Reconnecting The Ups

    Ups operation 55 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy reconnecting the ups use the following procedure to reinstall the ups and transfer the critical load from maintenance bypass (ac line operation) to the ups: 1. Reconnect t...

  • Page 62

    Ups operation 56 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 5. Press and hold the output on button until the alarm beeps again. Two indicators, corresponding with the current setting, remain flashing. The output voltage is factory-...

  • Page 63: Ommunication

    57 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy c h a p t e r 5 c ommunication the ups is equipped with a communications interface port that allows communication with a wide variety of external devices including: : video or dumb term...

  • Page 64

    Communication 58 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy front panel communications access before you access the front panel, review the following configurations and note the indicator that corresponds with the communication mod...

  • Page 65

    Communication 59 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy to access the front panel communication options, perform the following steps: 1. If the ups is powered on, prepare your equipment for shutdown. Press and hold the output o...

  • Page 66

    Communication 60 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ups serial communications menu with the ups serial communications (main) menu, you can view or select ups communication modes, baud rates, and lan configurations. To chang...

  • Page 67

    Communication 61 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy &dwdorj '& 1hz &200 $6&,, 3uhvv vsdfh edu wr frqwlqxh 6huldo 9huvlrq &200 prgh %dxg [ /$1 prgh %3& 6hub3ulqw 1ryhoo 1hz %dxg 1hz /$1 1ryhoo 6lwh )dxow 'hwhfwlrq 'lvdeohg n...

  • Page 68

    Communication 62 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 6(/(&7 /$1 &21),*85$7,21 ! 129(// (17(5 6(/(&7,21 !! 4 ! ! ! ! $6 &20/$1 0$1$*(5 &86720 &21),*85$7,21 72 48,7 7+,6 0(18 select the as400 option if you are using onlisafe s...

  • Page 69: Power Management Software

    Communication 63 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy z > set baud rate allows you to select a new baud rate. The select baud rate menu displays a list of baud rate options. 6(/(&7 %$8' 5$7( ! (17(5 6(/(&7,21 !! 4 ! ! ! ! ! !...

  • Page 70: C A U T I O N

    Communication 64 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy ups communications interface port in addition to configuring the ups for specific communication options, you must also ensure proper use of the serial port when connecting...

  • Page 71

    Communication 65 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy communications mode reference chart the following chart defines the ups serial port contacts. Serial communication is not available with 3com and as/400 network configurat...

  • Page 72

    Communication 66 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy this page intentionally left blank..

  • Page 73: Pecifications

    67 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy c h a p t e r 6 s pecifications 3000 va model specification with ppdm voltage in:out input output current voltage in:out input current output current (total not to exceed 2000 watts, 30...

  • Page 74

    Specifications 68 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy prestige 3000 ups technical specifications input voltage range 160 to 276 vac input power factor 0.95 typical frequency range 50/60 hz ±3 hz surge protection iec 801-4 ou...

  • Page 75: Part Numbers

    Specifications 69 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy part numbers base equipment machine type model ibm part number va watts volts frequency description 9910 ep5 21h1572 3000 2100 120/208 or 120/240 50-60 prestige 3000 mode...

  • Page 76

    Specifications 70 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy optional accessories ibm part number ibm type/model description 21h8444 9910-6602 prestige 3000 full battery pack manuals ibm order number description sc21-8379 powerware...

  • Page 77: Roubleshooting

    71 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy c h a p t e r 7 t roubleshooting the prestige ups is designed for durable, automatic operation and also alerts you whenever potential operating problems may occur. Use the following tro...

  • Page 78

    Troubleshooting 72 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy action possible cause condition communications do not function properly. Incorrect communications cabling. Verify cable integrity (see page 64). Incorrect baud rate. Sel...

  • Page 79: Resetting The Ups

    Troubleshooting 73 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy action possible cause condition battery weak battery while in bypass mode. This usually indicates that the batteries need replacing or the ups requires service. Contact ...

  • Page 80

    Troubleshooting 74 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy this page intentionally left blank..

  • Page 81: As/400 S

    75 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy c h a p t e r 8 as/400 s ervice the following sections describe the methods for obtaining service for your ups and warranty information. Warranty the warranty service on powerware upss ...

  • Page 82: Battery Warranty

    As/400 service 76 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy battery warranty if, in powerware corporation’s opinion, the unit fails to meet published specifications and the defect is within the terms of the limited warranty (attac...

  • Page 83: Customer Responsibilities

    As/400 service 77 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy customer responsibilities the customer is responsible for the following element exchange items: : receiving, unpacking, and exchanging of the defective element. : repacki...

  • Page 84: Upss

    As/400 service 78 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy handling of incomplete, damaged, or incorrectly shipped 9910 upss if the customer initially receives a 9910 ups that is incomplete, damaged, or incorrectly shipped: 1. Th...

  • Page 85: Emea

    As/400 service 79 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy emea customer process for service 1. Customer calls the local ibm office servicing account. 2. The ibm ce responds, determines the problem, and resolves the problem. Ibm ...

  • Page 86

    As/400 service 80 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy powerware protection guarantee attached equipment protection program terms and conditions program summary: powerware corporation guarantees to repair or replace (at the o...

  • Page 87: Ndex

    81 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy i ndex numeric 3com network interface front panel configuration, 58 lan configuration menu, 62 a ac line bypass switch, 53 operation, 53 alarm silencing, 73 ups, 72 alarm conditions bat...

  • Page 88

    Index 82 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy d data dump modes, 61 diagnostics, 50 display configuration screen, 61 e exiting main menu, 63 f front panel configuring communications, 58 display functions, 47 indicators, 47 fr...

  • Page 89

    Index 83 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy o operating modes, 48 operation battery, 49 bypass, 49 normal, 48 ups with ppdm, 53 output off button, 5, 47 output on button, 5, 47 output voltage changing, 51 initial setting, 4...

  • Page 90

    Index 84 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy service and support, 75 set baud rate menu, 63 shutdown, 51 site fault, indicator, 47 smart dump mode, 61 specifications, 67 startup tests, 50 storage temperature, 35 switch, bypa...

  • Page 91

    85 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy.

  • Page 92

    86 powerware ® prestige series installation and operator’s manual for ibm applications (3000 va) uncontrolled copy 164201134 c.