- DL manuals
- 3Com
- Switch
- S7500-LSQM1SRPB0-SALIENCE VI FRU PRE REL
- Installation Manual
3Com S7500-LSQM1SRPB0-SALIENCE VI FRU PRE REL Installation Manual
Summary of S7500-LSQM1SRPB0-SALIENCE VI FRU PRE REL
Page 1
H3c s7500e series ethernet switches installation manual hangzhou h3c technologies co., ltd. Http://www.H3c.Com manual version: t2-080406-20080725-c-1.04.
Page 2
Copyright © 2007-2008, hangzhou h3c technologies co., ltd. All rights reserved no part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of hangzhou h3c technologies co., ltd. Trademarks h3c, , aolynk, , h 3 care, , top g, , irf, netpilot, neoc...
Page 3: About This Manual
About this manual organization h3c s7500e series ethernet switches installation manual is organized as follows: chapter contents 1 product overview introduces the h3c s7500e series ethernet switches in terms of chassis, srpus, lpus, power supply, and fan tray. 2 installation preparations specifies t...
Page 5
Iii. Symbols convention description warning means reader be extremely careful. Improper operation may cause bodily injury. Caution means reader be careful. Improper operation may cause data loss or damage to equipment. Note means a complementary description. Related documentation in addition to this...
Page 6
Environmental protection this product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed..
Page 7: Table of Contents
Installation manual h3c s7500e series ethernet switches table of contents i table of contents chapter 1 product overview ........................................................................................................ 1-1 1.1 introduction ........................................................
Page 8
Installation manual h3c s7500e series ethernet switches table of contents ii 1.5.1 purchasing a switch.............................................................................................. 1-74 1.5.2 purchasing srpus ..............................................................................
Page 9: Chapter 1 Product Overview
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-1 chapter 1 product overview 1.1 introduction the s7500e series ethernet switches (hereinafter referred to as the s7500e series) are high performance, cost-effective layer-3 switches with a large capacity. The s7500...
Page 10
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-2 model dimensions (h × w × d) s7506e-v 930 × 436 × 420 mm (36.61 × 17.17 × 16.54 in.) note: z the backplane, switching & routing processing unit (srpu), power modules, and fan tray are all required parts of the s75...
Page 11
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-3 z the two power modules, which sit in the upper part of the chassis provide 1+1 redundancy backup. See callout (1) in figure 1-1. You can select either ac power supply or dc power supply. Figure 1-2 shows the rear...
Page 12
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-4 (1) power modules (2) srpus (in slot 0) (3) fan tray (4) lpus (in slot 1 and slot 2) (5) jack for esd-preventive wrist strap figure 1-3 front panel of the s7503e-s all modules of the s7503e-s are hot swappable. Z ...
Page 13
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-5 there are two dc power input (poe power supply input) terminals and two com ports (monitor ports) on the rear panel of the chassis. Iii. S7503e figure 1-5 shows the front panel of the s7503e. (1) (3) (4) (5) (2) (...
Page 14
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-6 (1) (3) (4) (5) (2) (3) (1) fan tray (2) jack for esd-preventive wrist strap (3) power module (4) lpus (in slot 2 to slot 7) (5) srpus (in slot 0 and slot 1) figure 1-6 front panel of the s7506e all the modules of...
Page 15
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-7 (3) (5) (4) (4) (3) (1) (2) (1) fan tray (2) jack for esd-preventive wrist strap (3) power module (4) lpus (in slot 0 to slot 4 and slot 7 to slot 11) (5) srpus (in slot 5 and slot 6) figure 1-7 front panel of the...
Page 16
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-8 vi. S7506e-v figure 1-8 shows the front panel of the s7506e-v. (1) (4) (2) (6) (3) (4) (5) (1) fan tray (2) lpus (in slot 2 to slot 7) (3) jack for esd-preventive wrist strap (4) power module (5) air filter (6) sr...
Page 17
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-9 active-standby switchover. Different lpus are inserted in the other six slots (see callout (2) in figure 1-8). Z the fan tray is installed above the srpus and lpus (see callout (1) in figure 1-8) and the air flows...
Page 18
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-10 table 1-4 features of power modules feature description protection functions support input under-voltage protection, output over-voltage protection, short-circuit protection, over-current protection, and overheat...
Page 19
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-11 chassis (right) power module (below) s7502e s7503e- s s7503e s7506e s7506e- v s7510 e psr2800-ac v n n y1 y1 y1 y1 note: z y1 means that the power module directly fits the chassis. Z y2 means that you need to ins...
Page 20
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-12 note: the psr320-a uses a 10-a ac power cable. Ii. Psr320-d (1) grounding screws (2) rtn terminal (+) of dc input (3) negative terminal (–) of dc input (–48 v to –60 v) (4) power switch (5) power led (6) power mo...
Page 21
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-13 above the power switch is the power led. If the power led is green, the power supply operates normally. If the led is red, the power supply is abnormal. Table 1-8 technical specifications of the psr650-a power mo...
Page 22
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-14 v. Psr1400-a (2) (6) (4) (5) (3) (1) (1) captive screws (2) power switch (3) power leds (4) ac power socket (5) power cable retainer (6) power module handle figure 1-13 psr1400-a power module on the right of the ...
Page 23
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-15 vi. Psr1400-d (8) (6) (4) (5) (3) (7) (2) (1) (1) captive screws (2) com port for monitoring poe (3) power leds (4) negative terminal (–) of dc input (–48 v to –60 v) (5) rtn terminal (+) of dc input (6) power mo...
Page 24
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-16 table 1-11 technical specifications of the psr1400-d dc power module item specifications rated voltage range –48 vdc to –60 vdc maximum system output power 1400 w maximum poe output power 6720 w dimensions (h × w...
Page 25
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-17 caution: keep the poe power switch in the off position unless the device needs to offer poe supply and is equipped with appropriate poe-capable cards. On the right of the panel are the input led, output led, fan ...
Page 26
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-18 when the system power consumption of a switch (s7503e, s7506e, s7506e-v, or s7510e) is less than the maximum output power of a 1u power module, you can first insert the pwr-spa power module adapters into the swit...
Page 27
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-19 model power consumption (w) s7510e fan tray 50 s7506e-v fan tray 50 1.2.5 air filter over a long period of time, dust may block the air filter at the air intake vent of the s7500e series. As a result, the heat di...
Page 28
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-20 chassis (right) engine (below) s7502e s7503e -s s7503e s7506e s7510e s7506e -v lsq1srp12gb0 (salience vi-ge) no no yes yes yes yes note: the s7500e series, except the s7503e-s, are a dual-srpu system. The srpus i...
Page 29
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-21 iii. Panel and leds figure 1-18 shows the front panel of the lsq1mpua0. (1) cf card interface and cfs led (2) console port (3) 10/100base-tx ethernet port for management and leds (4) power and fan tray status led...
Page 30
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-22 item specifications transmission distance 15 m (49.21 ft.) functions z it can be connected to an ascii terminal. Z it can be connected to a serial port of a local or remote (through a pair of modems) pc running t...
Page 31
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-23 table 1-20 description of the power status leds led description on: the power module works normally. Ok off: the power module is faulty or out of position. On: the power module is faulty, or there is no power inp...
Page 32
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-24 vi. Reset button a reset button is provided on the lsq1mpua0 for you to reset the card when necessary. 1.3.3 dedicated s7503e-s srpu-lsq1cgp24tsc0 i. Applicable model s7503e-s ii. Technical specifications table 1...
Page 33
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-25 iv. On-board interfaces z optical ethernet ports and combo ports the lsq1cgp24tsc0 provides twenty-four 1000base-x-sfp/100base-fx-sfp ports and eight 10/100/1000base-t ge ports. The eight ge ports and eight of th...
Page 34
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-26 note: in a combo port, only one of the 1000base-x-sfp/100base-fx-sfp port and the 10/100/1000base-t ge port can be used at a time. Each ethernet port has a green led. Table 1-26 describes the leds. Table 1-26 des...
Page 35
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-27 table 1-28 specifications of the 10/100base-tx ethernet port for management item specifications connector type rj-45 number of connectors 1 interface speed 10/100 mbps, half/full duplex connecting cable and maxim...
Page 36
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-28 table 1-31 description of the fan status leds led description ok z on: the fans operate normally. Z off: the fans are faulty or out of position. Fail z on: the fans are faulty or out of position. Z off: the fans ...
Page 37
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-29 ii. Technical specifications table 1-33 technical specifications of the lsq1srp2xb0 item specifications cpu mips64, 600 mhz boot rom 512 kb flash memory 64 mb ddr sdram 512 mb dimensions (h × w × d) 45 × 377 × 35...
Page 38
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-30 table 1-34 description of the cfs led status description off no cf card is in position. On the cf card is in position. Z 10gbase-r-xfp ethernet ports table 1-35 specifications of the 10gbase-r-xfp ethernet ports ...
Page 39
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-31 item specifications functions z it can be connected to an ascii terminal. Z it can be connected to a serial port of a local or remote (through a pair of modems) pc running terminal emulation program. Z 10/100base...
Page 40
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-32 table 1-40 description of the power status leds led description on: the power modules operate normally. Ok off: the power module is faulty or out of position. On: at least one power module is faulty or switched o...
Page 41
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-33 vi. Reset button a reset button is provided on the lsq1srp2xb0 for you to reset the card when necessary. 1.3.5 salience vi srpu-lsq1srpb0 i. Applicable models z s7503e z s7506e z s7510e z s7506e-v ii. Technical s...
Page 42
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-34 iv. On-board interfaces z cf card slot the cf card slot can accommodate a standard cf card (type i or type ii), where you can store host software and logs, and thus upgrade software conveniently. The cf card is h...
Page 43
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-35 table 1-46 specifications of the 10/100base-tx ethernet port item specifications connector type rj-45 number of interfaces 1 interface speed 10/100 mbps, half/full duplex connecting cable and maximum transmission...
Page 44
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-36 table 1-49 description of the fan status leds led description ok z on: the fans operate normally. Z off: the fans are faulty or out of position. Fail z on: the fans are faulty or out of position. Z off: the fans ...
Page 45
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-37 ii. Technical specifications table 1-51 technical specifications of lsq1srp1cb0 item specifications cpu mips64, 600 mhz boot rom 512 kb flash memory 64 mb ddr sdram 512 mb card physical dimensions (h x w x d) 45....
Page 46
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-38 table 1-52 description of the cfs led status description off no cf card is in position. On the cf card is in position. Z console port using an rj-45 connector, the console port can be connected through a regular ...
Page 47
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-39 item specifications function used for switch software upgrade and network management table 1-55 describes the status leds of the 10/100base-tx management ethernet port. Table 1-55 description of the status leds o...
Page 48
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-40 table 1-57 description of the fan status leds led description ok z on: the fans operate normally. Z off: the fans are faulty or out of position. Fail z on: the fans are faulty or out of position. Z off: the fans ...
Page 49
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-41 ii. Technial specifications table 1-59 technical specifications of the lsq1mpub0 item specifications cpu mips64, 600 mhz boot rom 512 kb flash memory 64 mb ddr sdram 512 mb dimensions (h x w x d) 45 × 377 × 355 m...
Page 50
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-42 table 1-60 specifications of the console port item specifications connector type rj-45 number of connectors 1 interface standard asynchronous eia/tia-232 baud rate 115,200 bps (defaulting to 9,600 bps) transmissi...
Page 51
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-43 v. System leds z system status leds the leds on the card panel indicate the statuses of the power modules, fans, lpus seated in the twelve slots, and lsq1mpub0 itself. Z power status leds pwr: the power status le...
Page 52
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-44 note: if the run led flashes at a high frequency, the card is in the startup process, but is not yet operational. At system startup, the alm led will be on for a while, but it does not mean that the card is fault...
Page 53
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-45 iii. Panel and leds figure 1-24 shows the front panel of the lsq1srpd0. (1) cf card slot and cf card status led (2) console port (3) 10/100base-tx management ethernet port and leds (4)power module and fan status ...
Page 54
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-46 table 1-68 specifications of the 10/100base-tx management ethernet port item specifications connector type rj-45 number of interfaces 1 interface speed 10/100 mbps, half/full duplex cable medium and maximum trans...
Page 55
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-47 table 1-71 description of the fan status leds led description ok z on: the fans operate normally. Z off: the fans are faulty or out of position. Fail z on: the fans are faulty or out of position. Z off: the fans ...
Page 56
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-48 ii. Technial specifications table 1-73 technical specifications of the lsq1sr12gb0 item specifications cpu dual cpus: z mips64, 600 mhz z mips64, 400 mhz boot rom 512 kb flash memory 64 mb ddr sdram 512 mb dimens...
Page 57
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-49 table 1-74 description of the cfs led status description off no cf card is in position. On the cf card is in position. Z ge/fe sfp ports table 1-75 presents the specifications of the ge/fe ports. Table 1-75 speci...
Page 58
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-50 table 1-77 specifications of the console port item specifications connector type rj-45 number of connectors 1 interface standard asynchronous eia/tia-232 baud rate 115,200 bps (defaulting to 9,600 bps) transmissi...
Page 59
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-51 v. System leds z system status leds the leds on the card panel indicate the statuses of the power modules, fans, lpus seated in the twelve slots, and lsq1sr12gb0 itself. Z power status leds pwr: the power status ...
Page 60
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-52 note: if the run led flashes at a high frequency, the card is in the startup process, but is not yet operational. At system startup, the alm led will be on for a while, but it does not mean that the card is fault...
Page 61
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-53 ii. Panel and leds figure 1-26 lsq1fp48sa0 panel each 100m ethernet optical port has a green led. Table 1-84 describes the led. Table 1-84 description of the led of each port on the lsq1fp48sa0 panel led descript...
Page 62
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-54 ii. Panel and leds figure 1-27 lsq1fv48sa0 panel each 10/100m auto-sensing ethernet electrical port has a green led. Table 1-86 describes the led. Table 1-86 description of the led of each port on the lsq1fv48sa0...
Page 63
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-55 ii. Panel and leds figure 1-28 lsq1gp12ea0 panel each 1000base-x-sfp ethernet port has a green led. Table 1-88 describes the led. Table 1-88 description of the led of each port on the lsq1gp12ea0 panel led descri...
Page 64
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-56 ii. Panel and leds figure 1-29 lsq1gp12sc0 panel each 1000base-x-sfp/100base-fx-sfp ethernet port has a green led. Table 1-90 describes the led. Table 1-90 description of the led of each port on the lsq1gp12sc0 p...
Page 65
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-57 item specifications standards z ieee 802.3-2005 z ieee 802.1d-2004 z ieee 802.1q-2003 z ieee802.1x-2004 ii. Panel and leds figure 1-30 lsq1gp24sc0 panel each 1000base-x-sfp/100base-fx-sfp ethernet port has a gree...
Page 66
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-58 item specifications pluggable module type z gigabit sfp module z 100 mbps sfp module refer to “appendix a list of pluggable modules.” standard z ieee 802.3-2005 z ieee 802.1d-2004 z ieee 802.1q-2003 z ieee802.1x-...
Page 67
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-59 item specifications number of ports 24 interface speed z 10/100/1000 mbps, half/full duplex z mdi/mdi-x auto-sensing cable medium and maximum transmission distance category-5 twisted pair cables, with a maximum t...
Page 68
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-60 item specifications power consumption 60 w to 80 w connector type rj-45 number of ports 48 interface speed z 10/100/1000 mbps, half/full duplex z mdi/mdi-x auto-sensing cable medium and maximum transmission dista...
Page 69
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-61 item specifications ddr sdram 512 mb dimensions (h x w x d) 40 × 377 × 355 mm (1.57 × 14.84 × 13.98 in.) power consumption 60 w to 90 w connector type rj-45 number of ports 48 interface speed z 10/100/1000 mbps, ...
Page 70
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-62 table 1-101 technical specifications of the lsq1p24xgsc0 item specifications cpu mips64, 400 mhz boot rom 512 kb ddr sdram 512 mb dimensions (h x w x d) 40 × 377 × 355 mm (1.57 × 14.84 × 13.98 in.) power consumpt...
Page 71
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-63 table 1-103 description of the leds of the 10gbase-r-xfp ethernet port led description link z off: no link is present. Z on: a link is present. Act z off: no data is being transmitted or received. Z blinking: dat...
Page 72
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-64 ii. Panel and leds figure 1-36 lsq1t24xgsc0 panel each auto-sensing 10/100/1000base-t ethernet port has a green led. Table 1-105 describes the led. Table 1-105 description of the led of the auto-sensing 10/100/10...
Page 73
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-65 item specifications number of ports 1 interface speed 10 gbps pluggable module type 10g xfp module refer to “appendix a list of pluggable modules.” standards z ieee 802.3-2005 z ieee 802.1d-2004 z ieee 802.1q-200...
Page 74
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-66 item specifications power consumption 30 w to 40 w connector type lc number of ports 2 interface speed 10 gbps pluggable module type 10g xfp module refer to “appendix a list of pluggable modules.” standards z iee...
Page 75
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-67 table 1-111 technical specifications of the lsq1gp24tsc0 item specifications cpu mips64, 400 mhz boot rom 512 kb ddr sdram 512 mb dimensions (h x w x d) 40 × 377 × 355 mm (1.57 × 14.84 × 13.98 in.) power consumpt...
Page 76
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-68 1000base-x-sfp/100base-fx-sfp ethernet port number 10/100/1000base-t ge port number 23 31 24 32 note: in a combo port, only one of the 1000base-x-sfp/100base-fx-sfp port and the 10/100/1000base-t ge port can be u...
Page 77
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-69 item specifications power consumption 41 w to 95 w connector type z sfp z rj-45 number of ports 40 rj-45 + 8 sfp interface speed z electrical ge port: 10/100/1000 mbps z gigabit sfp port: 100/1000 mbps pluggable ...
Page 78
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-70 table 1-116 technical specifications of the lsq1pt4psc0 item specifications cpu mips64, 400 mhz boot rom 512 kb ddr sdram 512 mb dimensions (h x w x d) 40 × 377 × 355 mm (1.57 × 14.84 × 13.98 in.) power consumpti...
Page 79
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-71 led status epon port status description on up an onu is registered. Likewise, each 1000base-x-sfp/100base-fx-sfp ethernet port has a green led. Table 1-118 describes the led of each 1000base-x-sfp/100base-fx-sfp ...
Page 80
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-72 item specifications pluggable module type z pluggable modules for epon interfaces z gigabit sfp module z 100 mbps sfp module refer to “appendix a list of pluggable modules.” standards z ieee 802.3-2005 z ieee 802...
Page 81
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-73 1.4.18 lsq1pt16psc0 i. Introduction the lsq1pt16psc0 provides sixteen epon ports and eight 1000base-x-sfp/ 100base-fx-sfp ethernet ports. Table 1-122 technical specifications of the lsq1pt16psc0 item specificatio...
Page 82
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-74 table 1-123 description of the epon port status and the led status of the lsq1pt16psc0 led status epon port status description off down no sfp module is installed. Off up an sfp module is installed but no onu is ...
Page 83
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-75 ii. Switch model table 1-125 list of the s7500e series models description quantity remarks s7502e switch 1 optional s7503e-s switch 1 optional s7503e switch 1 optional s7506e switch 1 optional s7510e switch 1 opt...
Page 84
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-76 1.5.2 purchasing srpus table 1-127 list of srpus for the s7500e series type quantity remarks lsq1mpua0 1 to 2 required for s7502e only lsq1cgp24tsc0 1 required for s7503e-s only salience vi-10ge 1 to 2 required s...
Page 85
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-77 type quantity remarks lsq1p24xgsc0 determined by the number of lpu slots provided by the chassis optional lsq1t24xgsc0 determined by the number of lpu slots in the chassis optional lsq1tgx1ea0 determined by the n...
Page 86
Installation manual h3c s7500e series ethernet switches chapter 1 product overview 1-78 1.5.6 purchasing fan trays table 1-130 list of fan trays for the s7500e series description quantity remarks h3c s7502e fan tray 0 to 1 optional h3c s7503e-s fan tray 0 to 1 optional h3c s7503e fan tray 0 to 1 opt...
Page 87: Table of Contents
Installation manual h3c s7500e series ethernet switches tables of contents i table of contents chapter 2 installation preparations............................................................................................. 2-1 2.1 safety instructions ...................................................
Page 88
Installation manual h3c s7500e series ethernet switches chapter 2 installation preparations 2-1 chapter 2 installation preparations 2.1 safety instructions to avoid damage to human body and devices, please read the following safety recommendations carefully before installing the s7500e series. The r...
Page 89
Installation manual h3c s7500e series ethernet switches chapter 2 installation preparations 2-2 caution: hold the handles on both sides of the chassis, instead of power handles or the vent of the chassis when moving the switch. Since the power handle or the vent is not designed to bear the weight of...
Page 90
Installation manual h3c s7500e series ethernet switches chapter 2 installation preparations 2-3 2.1.5 laser safety some lpus of the s7500e series have optical interfaces. In operating status, it is prohibited to stare into the open optical interface because the laser being transmitted through the op...
Page 91
Installation manual h3c s7500e series ethernet switches chapter 2 installation preparations 2-4 2.2.2 cleanness requirements dust is a big harm for the normal operation of the switch. The indoor dust accumulated on the chassis can cause electrostatic adsorption, resulting in the poor contact of the ...
Page 92
Installation manual h3c s7500e series ethernet switches chapter 2 installation preparations 2-5 z keep the switch far away from the radio launcher, radar launcher, and high-frequency devices working in high currents. If necessary, adopt electromagnetic shield. 2.2.4 grounding requirements a good gro...
Page 93
Installation manual h3c s7500e series ethernet switches chapter 2 installation preparations 2-6 2.4 installation tools table 2-4 required installation tools list type name tools measure and lineation tools long tape, ruler (of 1 meter), gradienter, marking pen, powder marker and pencil drills a perc...
Page 94: Table of Contents
Installation manual h3c s7500e series ethernet switches tables of contents i table of contents chapter 3 hardware installation .................................................................................................. 3-1 3.1 confirming installation preparations.................................
Page 95
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-1 chapter 3 hardware installation note: the s7500e series are designed for indoor application. 3.1 confirming installation preparations z make sure that you have read chapter 2 carefully z all requirements intr...
Page 96
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-2 3.3 mounting a switch to the designated position 3.3.1 mounting a switch into a cabinet after purchasing an s7500e ethernet switch, you can mount the switch into an h3c n68 cabinet or a standard 19” cabinet. ...
Page 97
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-3 2) mount weight-bearing guide rails on the n68 cabinet based on the installation position of the switch. (two types of weight-bearing guide rails are available. One is small guide rails and applicable to the ...
Page 98
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-4 note: z the s7500e series provide dual grounding screws in compliance with the nebs standard to deliver high reliability. Z generally, the cabinet has a grounding strip. The grounding cable of the switch can ...
Page 99
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-5 power input ethernet switch grounding screw angle steel ground protection grounding cable figure 3-4 connect the protection grounding cable to the grounding body nearby z if there is no grounding strip and no...
Page 100
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-6 dc power input ethernet switch rtn - 48v ac/dc power box - 48v strip rtn strip pgnd strip ground grounding screw figure 3-6 ground a dc-powered ethernet switch through the rtn wire of a power cabinet 3.5 inst...
Page 101
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-7 figure 3-8 connect the ac power cable for the psr320-a (ii) to connect the ac power cable for the psr320-a, proceed as follows: 1) plug one end of the ac power cable into the socket on the switch and lock the...
Page 102
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-8 3) plug the other end into the ac power socket strip, which is connected to the ac power supply in the equipment room. Iv. Psr2800-acv power module there are two ac power inputs on the psr2800-acv power modul...
Page 103
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-9 2) loosen the fastening screw on the wiring terminal with a phillips screwdriver. 3) connect the end of the blue dc power cable marked with – to the negative terminal (–) on the power module and fasten the sc...
Page 104
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-10 1) loosen the fastening screws on the protection cover with a phillips screwdriver and remove the protection cover. There are two flat washers, one spring washer, and one fastening nut m6 from inside to outs...
Page 105
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-11 note: z when you use psr1400-d modules to provide poe supply to attached devices and there are more than three poe-capable lpus in the switch, you are recommended to use 0awg cables with a cross section area...
Page 106
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-12 1) remove the protection cover from the terminals which are used to connect the external poe power supply. 2) use a socket wrench m5 to loosen the fastening nut on the input terminal of the switch, and a soc...
Page 107
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-13 table 3-1 console cable pinouts pin (rj-45) signal pin (db-9) signal 1 rts 8 cts 2 dtr 6 dsr 3 txd 2 rxd 4 sg 5 sg 5 sg 5 sg 6 rxd 3 txd 7 dsr 4 dtr 8 cts 7 rts ii. Connecting the console cable take the foll...
Page 108
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-14 3.7.3 connecting the com cable i. Introduction when connected to an external poe power supply, the s7500e series can monitor the running status of the external poe power supply through the com port. The com ...
Page 109
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-15 figure 3-15 rj-45 connector table 3-2 rj-45 mdi interface pinouts 10base-t/100base-tx 1000base-t pin signal function signal function 1 tx+ send data bida+ bi-directional data cable a+ 2 tx- send data bida- b...
Page 110
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-16 10base-t/100base-tx 1000base-t pin signal function signal function 5 reserved — bidd- bi-directional data cable d- 6 tx- send data bida- bi-directional data cable a- 7 reserved — bidc+ bi-directional data ca...
Page 111
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-17 figure 3-17 lc connector ii. Connecting fibers 1) remove the protective cap from the connector of the fiber and clean the surface of the fiber. 2) remove the protective cap from the optical interface of the ...
Page 112
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-18 equipment room (whether the signal cable of the room is accessed from the cabling rack on the top of the chassis or the cabling rack under the floor.) collect all the transit data signal cable connectors and...
Page 113
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-19 3.9.2 precautions for cable binding z bind the cables straight in the cabinet. No twisting or bending. Figure 3-18 cable binding example i z the radius of the curve at which a cable is bent should be at leas...
Page 114
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-20 figure 3-19 cable binding example ii z before bending the cables, bind them first. Mind that no tie binds the bended part of any cables, for fear of cable core breaking due to excessive stress. See the follo...
Page 115
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-21 (1) (2) (3) (4) (1) flat washer (2) flat washer (3) spring washer (4) fastening nut figure 3-21 cable fixing example z fix the terminal of harder power cables to free the terminal and the cable from stress; ...
Page 116
Installation manual h3c s7500e series ethernet switches chapter 3 hardware installation 3-22 3.10 checking the installation caution: confirm that you have turned off the power before check; otherwise, improper connection will hurt people or the component of the switch. After installing the switch, p...
Page 117: Table of Contents
Installation manual h3c s7500e series ethernet switches table of contents i table of contents chapter 4 system commissioning .............................................................................................. 4-1 4.1 configuration environment setup............................................
Page 118
Installation manual h3c s7500e series ethernet switches chapter 4 system commissioning 4-1 chapter 4 system commissioning 4.1 configuration environment setup 4.1.1 setting up networking environment z a terminal (a pc in this example) is connected to the console port of the switch with a console cabl...
Page 119
Installation manual h3c s7500e series ethernet switches chapter 4 system commissioning 4-2 1) start pc and run the terminal emulator (such as terminal on windows3.1, and the hyperterminal on windows95/windows98/windows 2000/windows nt/windows me/windows xp). 2) set the parameters for windows xp hype...
Page 120
Installation manual h3c s7500e series ethernet switches chapter 4 system commissioning 4-3 figure 4-3 set serial port for hyperterminal connection after selecting serial ports, click ok. The following interface will pop up for setting serial port parameters. Set bits per second to 9600, data bits to...
Page 121
Installation manual h3c s7500e series ethernet switches chapter 4 system commissioning 4-4 after setting serial port parameters, click ok. Then the system will enter the hyperterminal dialogue box as shown in the following figure. Figure 4-5 hyperterminal interface in the above dialogue box, select ...
Page 122
Installation manual h3c s7500e series ethernet switches chapter 4 system commissioning 4-5 figure 4-6 set terminal emulation in the property setting window 4.2 power-on startup 4.2.1 check before power-on before powering on an ethernet switch, check if: z the switch has been mounted steadily. Z all ...
Page 123
Installation manual h3c s7500e series ethernet switches chapter 4 system commissioning 4-6 caution: before powering on the switch, make sure where the power switch of the equipment room is located, so that you will be able to power off when meeting accidence. 4.2.2 power-on z turn on the power suppl...
Page 124
Installation manual h3c s7500e series ethernet switches chapter 4 system commissioning 4-7 bus clock speed : 66mhz boot_flash type : m29w040b flash size : 64mb memory size : 512mb main board slot 0 self testing............................ Sdram data lines selftest.................................Ok!...
Page 125
Installation manual h3c s7500e series ethernet switches chapter 4 system commissioning 4-8 note: h3c s7500e series switches provide a variety of command views. For the specific descriptions on the configuration commands and command line interfaces, refer to operation manual and command manual of the...
Page 126: Table of Contents
Installation manual h3c s7500e series ethernet switches table of contents i table of contents chapter 5 hardware maintenance................................................................................................ 5-1 5.1 required tools............................................................
Page 127
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-1 chapter 5 hardware maintenance caution: the power modules of the s7500e series are hot-swappable. When installing or replacing an in-service power module, pay attention to operations and electrical safety. Do ...
Page 128
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-2 5.2.1 removing and installing a power module i. Removing a power module 2 1 figure 5-1 remove a power module follow these steps to install a power module: 1) wear an esd-preventive wrist strap and loosen the c...
Page 129
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-3 ii. Installing a power module install a power module in the opposite order you remove it: 1) put on an esd-preventive wrist strap and take a new power module out of its package. Check that the input mode of th...
Page 130
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-4 5.3.1 removing a card 3 1 2 figure 5-2 remove a card follow these steps to remove a card: 1) wear an esd-preventive wrist strap and loosen the captive screws on the card with a screwdriver (see callout in ① fi...
Page 131
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-5 5.3.2 installing a card install a card in the opposite way you remove it: 1) wear an esd-preventive wrist strap and loosen the captive screws on the blank panel on the slot, where the card should be inserted. ...
Page 132
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-6 5.4.1 for the s7506e-v i. Removing the fan tray 1 2 3 figure 5-3 removing the fan tray of the s7506e-v follow these steps to remove the fan tray of the s7506e-v: 1) wear an esd-preventive wrist strap and loose...
Page 133
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-7 2) tighten the captive screws with a screwdriver. 3) push the handle into the groove. 5.4.2 for the other models i. Removing the fan tray figure 5-4 remove the fan tray of the other models follow these steps t...
Page 134
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-8 be installed in the lower part of the chassis. However, they are installed in the same way. The mounting ears of the s7500e series are installed in the same way. 5.5.1 installing cabling racks on the s7506e-v ...
Page 135
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-9 （1） （2） (1) left mounting ear (2) cabling rack figure 5-6 install the cabling rack onto the left mounting ear ii. Installing the mounting ears and cabling rack onto the chassis (1) mounting ear and cabling rac...
Page 136
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-10 5.6 installing and removing air filters (optional) 5.6.1 installing and removing air filters onto/from the s7506e-v figure 5-8 install a rear air filter on the s7506e-v figure 5-9 install a front air filter o...
Page 137
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-11 2) remove the air filters from the chassis. 5.6.2 installing and removing an air filter onto/from the other models 1 2 1 3 figure 5-10 install an air filter (on the s7503e) i. Installing an air filter follow ...
Page 138
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-12 5.7 installing and removing a cf card 5.7.1 cf card slot and cfs led (1) cfs led (2) cf card (3) cf card eject button figure 5-11 cf card slot and cfs led 5.7.2 install a cf card figure 5-12 install a cf card...
Page 139
Installation manual h3c s7500e series ethernet switches chapter 5 hardware maintenance 5-13 note: if you want to use the cf card after you execute the umount command, you can execute the mount command in user view to mount the cf card again. For detailed descriptions about the mount and umount comma...
Page 140: Table of Contents
Installation manual h3c s7500e series ethernet switches table of contents i table of contents chapter 6 software maintenance................................................................................................. 6-1 6.1 software maintenance overview ...........................................
Page 141
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-1 chapter 6 software maintenance 6.1 software maintenance overview software maintenance of a switch means to upgrade the switch host software and boot rom through the host software package, which contains the ho...
Page 142
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-2 of the srpus through the boot menu, refer to section 6.2.6 “updating boot rom through a file on the flash” on page 6-15. 6.2.1 boot menu upon power-on, the switch will run the boot rom program first. The follo...
Page 143
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-3 press ctrl+b. The system prompts you to input the boot rom password: password : note: to enter the boot menu, press ctrl+b within 5 seconds after “press ctrl+b to enter boot menu...” is prompted. Otherwise, th...
Page 144
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-4 ii. Downloading the host software package 1) connect the switch to the pc that stores the file to be downloaded through the management/upgrade ethernet port (the ip address of the pc is required). Connect the ...
Page 145
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-5 attaching network interf prepare for loading...Ok! Loading................................................................... .......................................................................... ...........
Page 146
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-6 in the following example, the switch functions as an ftp client. Ii. Loading the host software package 1) connect the switch to the pc that stores the file to be downloaded through the management/upgrade ether...
Page 147
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-7 6) type y and press enter. The system starts program downloading and upon its completion automatically starts to write the program to the flash. The system displays the following information upon the completio...
Page 148
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-8 6.2.4 downloading through the console port using xmodem i. Introduction to xmodem the xmodem protocol is a file transfer protocol widely used due to its simplicity and good performance. Xmodem transfers files ...
Page 149
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-9 3. Set xmodem protocol parameter 0. Return to boot menu enter your choice(0-4): 3 load file name :update.App 3) enter the file name to enter the download baud rate menu: please select your download baudrate: 1...
Page 150
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-10 figure 6-1 properties dialog box.
Page 151
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-11 figure 6-2 console port configuration dialog box 7) click connect to re-establish a connection with the switch and press enter to download the program. The terminal displays the following information: now ple...
Page 152
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-12 9) click send. The system displays the following interface. Figure 6-4 file sending interface after the downloading is completed, the system displays the following information: loading ...Cccccccccccccccccccc...
Page 153
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-13 to complete the host software upgrade, you need to set the main/backup attribute of the host software. For details, refer to 6.2.5 “setting the main and backup host software through the boot menu” on page 6-1...
Page 154
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-14 flash free space : 21444608 bytes the current application file is :switch000.App the backup application file is : switch100.App the system displays all files on the flash, wherein the file number with an aste...
Page 155
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-15 note: z if you do not specify the backup boot file but the main boot file only, the system boots with the main boot file. If the main boot file has an error, the system randomly chooses an application file fo...
Page 156
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-16 the backup boot file has not been selected. Please input the file number:0 4) enter file number 0 to select to upgrade the boot rom program through the host software package. The system prompts you whether to...
Page 157
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-17 6.3 upgrading through command lines if your terminal is connected to the switch over a network, you can upgrade the boot rom program and host software through command lines. 6.3.1 upgrading using ftp run the ...
Page 158
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-18 bootrom update succeeded. 3) set the main and backup boot files. Z set the main boot file. Boot-loader file flash:/ switch002.App slot 0 main this command will set boot file of the specified board, continue? ...
Page 159
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-19 z the host software package for upgrade is s7502e002.App. Z the host software package the system currently runs is s7502e001.App. Z slot 0 is for the active srpu. Z slot 1 is for the standby srpu. Z slot 3 is...
Page 160
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-20 start accessing bootflash chip... Board has finished to load file in frame 0 slot 3. Bootrom update succeeded. Z upgrade the boot rom program on the active srpu. Bootrom update file flash:/ s7502e002.App slot...
Page 161
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-21 this command will set boot file of the specified board, continue? [y/n]:y the specified file will be used as a backup boot file at the next time! Note: the host software package on the active srpu can be used...
Page 162
Installation manual h3c s7500e series ethernet switches chapter 6 software maintenance 6-22 z after the system is rebooted, upgrade the boot rom program on the lpu through command lines. For the command lines, refer to section 6.4.1 i. 2)”upgrade the boot rom program.” on page 6-18. Caution: z the s...
Page 163: Table of Contents
Installation manual h3c s7500e series ethernet switches table of contents i table of contents chapter 7 troubleshooting .......................................................................................................... 7-1 7.1 troubleshooting the configuration system ...........................
Page 164: Chapter 7 Troubleshooting
Installation manual h3c s7500e series ethernet switches chapter 7 troubleshooting 7-1 chapter 7 troubleshooting although the s7500e series have passed the comprehensive and strict test before delivery, faults may occur due to improper installation. This chapter describes how to handle faults caused ...
Page 165
Installation manual h3c s7500e series ethernet switches chapter 7 troubleshooting 7-2 –flow control: none –terminal emulation mode: vt100 z something is wrong with the console cable. 7.1.2 illegible characters on the terminal if the configuration terminal displays illegible characters, configuration...
Page 166
Installation manual h3c s7500e series ethernet switches chapter 7 troubleshooting 7-3 table 7-1 description of leds on the psr1400-a case led color status input green the power input is normal. Output red no power is output. The power module is connected but the power switch is turned off. Fan red t...
Page 167
Installation manual h3c s7500e series ethernet switches chapter 7 troubleshooting 7-4 table 7-2 description of leds on the psr1400-d case led color status input off the power input is normal. Output off no power is output. Fan off a fan does not rotate. The power module is connected but the system p...
Page 168
Installation manual h3c s7500e series ethernet switches chapter 7 troubleshooting 7-5 7.2.5 troubleshooting psr2800-acv on the right of the psr2800-acv power module panel are the input led, output led, fan led, poe input led, and poe output led. Compared with the psr1400-a power module, the psr2800-...
Page 169: Table of Contents
Installation manual h3c s7500e series ethernet switches table of contents i table of contents appendix a list of pluggable modules.......................................................................................A-1 a.1 10g xfp modules ..............................................................
Page 170
Installation manual h3c s7500e series ethernet switches appendix a list of pluggable modules a-1 appendix a list of pluggable modules a.1 10g xfp modules table a-1 specifications of 10g xfp modules type central wavelength connector type cable specifications maximum transmission distance xfp-sx-mm850...
Page 171
Installation manual h3c s7500e series ethernet switches appendix a list of pluggable modules a-2 type central wavelength connect or type cable specifications maximum transmission distance sfp-ge-lx-s m1310-bidi 1490 nm (receive)/1310 nm (transmit) lc 9/125µm single mode fiber 10 km (6.21 miles) sfp-...
Page 172
Installation manual h3c s7500e series ethernet switches appendix a list of pluggable modules a-3 type central wavelength connect or type cable specifications maximum transmission distance sfp-fe-lx-s m1310-bidi 1550 nm (receive)/1310 nm (transmit) lc 9/125µm single mode fiber 15 km (9.32 miles) sfp-...
Page 173: Table of Contents
Installation manual h3c s7500e series ethernet switches table of contents i table of contents chapter b ac power cables used in different countries or regions.....................................B-1 b.1 10a ac power cables used in different countries or regions..........................................
Page 174: Countries Or Regions
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-1 chapter b ac power cables used in different countries or regions b.1 10a ac power cables used in different countries or regions table b-1 10a ac power cables used in different...
Page 175
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-2 conne ctor type code (length) countries or regions where the type of power cables conforms to local safety regulations and can be used legally other countries or regions using...
Page 176
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-3 conne ctor type code (length) countries or regions where the type of power cables conforms to local safety regulations and can be used legally other countries or regions using...
Page 177
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-4 conne ctor type code (length) countries or regions where the type of power cables conforms to local safety regulations and can be used legally other countries or regions using...
Page 178
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-5 conne ctor type code (length) countries or regions where the type of power cables conforms to local safety regulations and can be used legally other countries or regions using...
Page 179
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-6 b.2 16a ac power cables used in different countries or regions table b-2 16a ac power cables used in different countries or regions connec tor type code (length) countries or ...
Page 180
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-7 connec tor type code (length) countries or regions where the type of power cables conforms to local safety regulations and can be used legally other countries or regions using...
Page 181
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-8 connec tor type code (length) countries or regions where the type of power cables conforms to local safety regulations and can be used legally other countries or regions using...
Page 182
Installation manual h3c s7500e series ethernet switches chapter b ac power cables used in different countries or regions b-9 connec tor type code (length) countries or regions where the type of power cables conforms to local safety regulations and can be used legally other countries or regions using...
Page 183: Table of Contents
Installation manual h3c s7500e series ethernet switches table of contents i table of contents chapter c compliance and safety manual .................................................................................C-1 c.1 regulatory compliance statement..................................................
Page 184
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-1 chapter c compliance and safety manual c.1 regulatory compliance statement c.1.1 european community ce certification doc figure c-1 european community ce certification doc.
Page 185
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-2 c.2 regulatory compliance information c.2.1 regulatory compliance standards table c-1 regulatory compliance standards discipline standards emc fcc part 15 (cfr 47) class a ices-003 class a vcci class a...
Page 186
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-3 z this device must accept any interference received, including interference that may cause undesired operation. If the customer modifies the equipment without the authorization of h3c, which directly o...
Page 187
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-4 c.2.6 cispr 22 compliance h3c s7500e series (including h3c s7502e, h3c s7503e, h3c s7503e-s, h3c s7506e. H3c s7506e-v and h3c s7510e) complies with the requirements of cispr 22 for class a information ...
Page 188
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-5 anmerkung: lesen sie bitte alle arbeitsanweisungen und sicherheitvorschriften sorgfältig durch, bevor sie mit dem arbeiten beginnen. Nur durch beachtung dieser hinweise lässt sich das unfallrisiko mini...
Page 189
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-6 以下表格中的安全标识，是用来提示读者在进行设备安装和维护时的安全预防要求。 table c-2 safety symbol and description sicherheitssymbole und beschreibung 安全标识和描述 safety symbol symbole 安全标识 description erläuterung 描述 generic alarm symbol: to ...
Page 190
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-7 z do not block ventilation openings while the system is on, and keep at least 5 cm distance from ventilation openings and walls or other things which may block the openings z sorgen sie dafür, dass die...
Page 191
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-8 z 该产品需要使用建筑物安装来提供短路保护，要求保险丝或者短路保护器不小于 120 vac, 15a u.S. (240 vac, 10a international),或者 80vdc, 238a. Z for ac supplied model: the plug-socket combination must be accessible at all times because it serv...
Page 192
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-9 gefahr: die hochspannungsleitungen stellen für die arbeit der ausrüstung erforderliche energie zur verfügung. Direkter oder indirekter kontakt (z. B. Durch feuchte gegenstände) mit hochspannung und wec...
Page 193
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-10 warning: non-standard and improper high voltage operations may result in fire and electric shock. Therefore, ac cable bridging and wiring through a certain area must follow the local rules and regulat...
Page 194
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-11 说明： 禁止安装和移动带电的线缆。因为导电体和带电的线缆，即使短暂接触，也会引起电火 花或电弧，从而导致失火或是伤害眼睛。 z before the power cable is installed or removed, the power switch must be turned off. Z das system muss stets abgeschaltet werden, bevor ...
Page 195
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-12 note: for h3c s7502e, h3c s7503e-s,: for dc power supplied equipment, please use 4 mm 2 or 10 awg minimum power supply cord. For poe input: please use 10 mm 2 or 6 awg minimum power supply cord for ac...
Page 196
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-13 说明： 对于 h3c s7502e, h3c s7503e-s,: dc 电源设备，请使用 4 mm 2 或 10 awg 电缆； poe 输入, 请使用 10 mm 2 或 6awg 电缆； ac 电源设备，请使用 1.25mm 2 或 16awg 电缆； 对于 h3c s7503e, h3c s7506e, h3c s7506e-v 和 h3c s7510e: dc 电源设备， 有 poe 功...
Page 197
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-14 c.3.3 fuse sicherung 保险丝 warning: for the safety of continuous operation, please replace the fuse with that of the same type and rating, if necessary. Warnung: ersetzen sie die sicherung bei bedarf im...
Page 198
Installation manual h3c s7500e series ethernet switches chapter c compliance and safety manual c-15 警告： 在安装和维护设备的光纤接口时，请不要把眼睛靠近或是直视这些光接口。.