Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page i instructions and parts list important safety information before installing or operating this equipment read, understand and follow all safety and operating instructions. Spare parts it is recommended you immediately order the spa...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page ii.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page iii replacement parts and service information to our customers: this is the 3m-matic ™ /accuglide ™ /scotch ® equipment you ordered. It has been set up and tested in the factory with scotch ® tapes. If technical assistance or repla...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page iv.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page v replacement parts and service information (continued) to our customers: this is the 3m-matic ™ /accuglide ™ /scotch ® equipment you ordered. It has been set up and tested in the factory with scotch ® tapes. If any problems occur ...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page vi.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page vii table of contents - manual 2: accuglide 3 high speed - 2 inch (upper and lower taping heads) accuglide 3 high speed taping head manual - 2 inch page cover page replacement parts and service information . . . . . . . . . . . . ....
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page viii warranty warranty equipment warranty and limited remedy: the following warranty is made in lieu of all other warranties, express or implied, including, but not limited to, the implied warranty of merchantability, the implied w...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 1 accuglide™ 3 upper taping head - 2 inch , type 10800 intended use the intended use of the accuglide™ 3 upper and lower taping heads - 2 inch is to apply a “c” clip of scotch ® pressure-sensitive fi lm box sealing tape to the top ...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 2.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 3 accuglide ™ 3 high speed - 2 inch upper and lower taping heads consist of: qty. Part name 1 taping head assembly 1 tape drum and bracket assembly 1 hardware and spare parts kit 1 threading tool general information this instructio...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 4 (important safeguards continued on next page) explanation of signal word and possible consequences indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury and/or property damage....
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 5 78-8070-1335-0 figure 1-1 replacement labels/3m part numbers important - in the event the following safety labels are damaged or destroyed, they must be replaced to ensure operator safety. See "replacement parts illustrations and...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 6 (speci fi cations continued on next page.) speci fi cations 1. Tape: for use with scotch ® pressure-sensitive fi lm box sealing tapes. 2. Tape width: 36mm or 1-1/2 inches minimum to 48mm [2 inches] maximum. 3. Tape roll diameter:...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 7 figure 2-1 dimensional drawing optional tape drum mounting position 6mm [1/4 in.] maximum 18mm [11/16 in.] box feed direction 18mm [11/16 in.] side view end view 76mm [3 in.] 50mm tape leg 76mm [3 in.] 6mm [1/4 in.] maximum 405mm...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 8 receiving and handling after the taping head assembly has been unpackaged, examine the unit for damage that might have occurred during transit. If damage is evident, fi le a damage claim immediately with the transportation compan...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 9 figure 3-2 taping head components/threading diagram - lower head (left side view) figure 3-1 taping head components/threading diagram - upper head (left side view) tape drum tape drum tape supply roll tape supply roll tape adhesi...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 10 figure 3-3 insert threading needle through rollers in direction indicated by arrows. Figure 3-3 tape loading/threading one-way tension roller 1 2 3 4 tension wrap roller knurled roller wrap roller applying roller operation (cont...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 11 figure 3-4 tape loading/threading figure 3-5 tape loading/threading operation (continued) figure 3-4 place tape roll on tape drum to dispense tape with adhesive side forward. Seat tape roll fully against back fl ange of drum. Ad...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 12 (maintenance continued on next page.) figure 4-1 blade replacement knife guard knife holder a a b b maintenance the accuglide™ 3 high speed 2 inch taping head has been designed for long, trouble free service. The taping head wil...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 13 figure 4-2 roller shaft section view 5mm hex key wrench section view of roller/shaft hex socket maintenance (continued) cleaning regular slotted containers produce a great deal of dust and paper chips when conveyed through tapin...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 14 figure 5-1 tape latch alignment figure 5-2 tape web alignment figure 5-3 tape drum friction brake (adjustments continued on next page.) 5mm hex wrench shaft 25mm hex wrench adjustment nut, tape drum brake adjustments tape latch ...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 15 applying mechanism spring to obtain access to spring, remove taping head cover (four mounting screws). Replace cover to fi nish. The applying mechanism spring, shownin figures 5-4a and 5-4b , controls applying/bu ffi ng roller p...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 16 figure 5-6 leading tape leg length one-way tension roller tape leg 50 or 70mm ± 6mm [2 or 2-3/4in. ± 1/4in. Slot c-c position b-b brush slot c position b figure 5-7 changing tape leg length position a-a position a adjustments (c...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 17 cause the tape is threaded incorrectly the tape tension is too low the knurled roller drags tape tracks to one side or drags on the support tabs of applying frame the one-way tension roller is not correctly positioned taping hea...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 18 problem tape is tabbing on the trailing leg on the back of the box the tape end does not stay in application position in front of the applying roller tape not centered on box seam cause there is excess tension on the tape drum a...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 19 recommended spare parts listed are a set of spare parts that will periodically require replacement due to normal wear. These parts should be ordered to keep the taping heads in production: accuglide™ 3 upper taping head - 2 inch...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 20
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 21 replacement parts illustrations and parts lists accuglide™ 3 high speed 2 inch upper taping head, type 10800 accuglide™ 3 high speed 2 inch lower taping head, type 10800 1. Refer to the taping head assemblies figure to fi nd all...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 22.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 23 tape head figures accuglide™ 3 - 2 inch accuglide ™ 3 - 2" figure 10919 figure 10920 figure 10921 figure 10922 figure 10925 figure 10923 figure 10924 figure 10401.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 24 accuglide ™ 3 - 2" 24 25 1 3 2 4 8 11 10 12 16 15 17 17 18 19 13 13 13 9 7 5 23 13 23 27 20 29 27 26 28 29 21 figure 10925 – upper head.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 25 figure 10925 – 2" upper head ref. No. 3m part no. Description 10925-1 78-8137-3294-4 frame – tape mount upper assembly 10925-2 78-8137-3295-1 frame – front upper assembly 10925-3 78-8068-4143-9 guide – #1 10925-4 78-8068-4144-7 ...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 26 15 14 12 12 11 10 13 15 16 16 1 4 4 3 7 2 5 6 8 8 9 9 figure 10922 – upper and lower heads accuglide ™ 3 - 2".
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 27 figure 10922 – 2" upper and lower heads ref. No. 3m part no. Description 10922-1 78-8133-9509-8 applying arm #1 10922-2 78-8133-9510-6 applying arm #2 10922-3 78-8070-1221-2 plate – tape 10922-4 78-8070-1309-5 shaft roller 10922...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 28 accuglide ™ 3 - 2" 8 7 7 7 7 7 7 2 1 9 6 4 3 5 figure 10919 – upper head.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 29 figure 10919 – 2" upper head ref. No. 3m part no. Description 10919-1 78-8137-3300-9 buffi ng arm – sub assembly 10919-2 78-8137-3301-7 buffi ng arm – sub assembly 10919-3 78-8052-6575-4 shaft – roller 10919-4 78-8137-1398-5 rol...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 30 figure 10923 upper and lower heads 1 7 7 3 8 5 5 4 4 9 9 6 6 figure 10923 – upper and lower heads accuglide ™ 3 - 2".
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 31 ref. No. 3m part no. Description 10923-1 78-8137-3302-5 link – assembly 10923-3 78-8137-3304-1 shaft – pivot, buffi ng 10923-4 78-8017-9082-1 bearing – special 30 mm 10923-5 78-8017-9106-8 screw – bearing shoulder 10923-6 26-100...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 32 figure 10921 – upper and lower heads accuglide ™ 3 - 2".
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 33 figure 10921 – 2" upper and lower heads ref. No. 3m part no. Description 10921-1 78-8137-3307-4 frame – cut-off weldment 10921-2 78-8017-9173-8 blade – 65 mm/2.56 inch 10921-3 26-1003-8596-7 screw - hex hd m5 x 8 w/ ext. Tooth l...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 34 figure 10401 – upper and lower heads accuglide ™ 3 - 2" 4 14 16 14 3 1 13 13 13 12 13 5 6 7 7 7 2 4 8 9 10 15 11.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 35 figure 10401 – 2" latch upper and lower heads ref. No. 3m part no. Description 10401-1 78-8070-1395-4 bracket – bushing assembly 10401-2 78-8076-4519-3 shaft – tape drum, 50mm 10401-3 78-8017-9169-6 nut – m18 x 1 10401-4 78-8098...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 36 26 8 2 4 8 13 13 13 13 15 29 29 18 27 24 25 27 28 16 17 17 19 26 9 7 3 1 11 12 10 20 21 23 23 5 figure 10924 – lower head accuglide ™ 3 - 2".
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 37 figure 10924 – 2" lower head ref. No. 3m part no. Description 10924-1 78-8137-3296-9 frame – tape mount lower assembly 10924-2 78-8137-3297-7 frame – front lower assembly 10924-3 78-8068-4144-7 guide – #2 10924-4 78-8068-4143-9 ...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 38 9 6 4 3 2 1 8 5 9 7 7 7 7 7 7 figure 10920 – lower head accuglide ™ 3 - 2".
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 39 figure 10920– lower head ref. No. 3m part no. Description 10920-1 78-8137-3300-9 buffi ng arm – sub assembly 10920-2 78-8137-3301-7 buffi ng arm – sub assembly 10920-3 78-8052-6575-4 shaft – roller 10920-4 78-8137-1398-5 roller ...
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 40
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 41.
Na - eng april 2017 3m-matic ™ accuglide 3 - 2 inch taping head page 42.