3M 28408 Instruction manuals - page 5
5
Safety Precautions
1. Read all instructions before using this tool. All operators must be fully
trained in its use and aware of these safety rules.
2. The tool RPM should be checked on a regular basis to ensure proper
operating speed.
3. Make sure the tool is disconnected from the air supply. Attach the 3M™
Disc Pad to the sander adaptor using the wrenches supplied with the tool.
Select a suitable abrasive and secure it to the disc pad.
4. Always wear required safety equipment when using this tool.
5. When sanding always start the tool just prior to contacting the work
piece. Stop air flow to the tool as it is removed from the work piece.
6. Always disconnect the air supply to the sander before fitting, adjusting or
removing the abrasive or disc pad.
7. Always adopt a firm footing and grip and be aware of torque reaction
developed by the sander.
8. Use only 3M approved spare parts.
9. Always ensure the material being worked is firmly fixed to avoid
movement.
10. Check hose and fittings regularly for wear. Do not carry the tool by its
hose; always be careful to prevent the tool from being started when
carrying the tool with the air supply connected.
11. Dust can be highly combustible. Keep working area clean.
12. If tool is serviced or rebuilt check to ensure that the maximum tool RPM is
not exceeded and that there is no excessive tool vibration.
13. Do not exceed maximum recommended air pressure. Use safety
equipment as recommended.
14. Prior to installing any sanding or polishing accessory, always check that
its marked maximum operating speed is equal or higher than the rated
speed of this tool.
15. The tool is not electrically insulated. Do not use where there is a
possibility of contact with live electricity, gas pipes, and/or water pipes.
16. This tool is not protected against hazards inherent in grinding and cutting
operations, which require a guard, and no such grinding and cutting
products should ever be attached.
17. Take care to avoid entanglement with the moving parts of the tool with
clothing, ties, hair, cleaning rags or loose hanging objects. If entangled,
stop air supply immediately to avoid contact with moving tool parts.
18. Keep hands clear of the spinning abrasive during use.
19. If the tool appears to malfunction, remove from use immediately and
arrange for service and repair.
20. Immediately release the start handle in the event of any disruption
of pressure; do not attempt to restart until the disruption has been
corrected.
21. Do not allow the tool to free spin without taking precautions to protect
any persons or objects from debris from rupturing abrasive & mounting
hardware.
22. When tool is not in use, store in a clean dry environment free of debris.
23. Operate tool in a well lit work area.
24. Recycle or dispose of tool according to Local, State, and Federal
regulations.
25. Whenever performing maintenance procedures, use care to avoid
exposure to any hazardous substances deposited on the tool as a result
of work processes. Also, refer to warnings related to dust exposure.
26. Ensure that the abrasive product is correctly mounted and tightened
before use and run the tool at no-load speed for at least 1 min in a safe
position; stop immediately if considerable vibration or other defects are
detected and determine the cause of these defects.
27. Whenever universal twist couplings (claw couplings) are used, lock-pins
shall be installed and whip check safety cables shall be used to safeguard
against possible hose-to-tool and hose-to-hose connection failure.
3M
™
Roloc
™
Disc Pads
3M Roloc Disc Pads are mated for use on the 3M Sander. Constructed
from premium, industrial-quality materials and their durability and precise
construction are the ideal complement to the performance of the 3M Sander.
Disc Pad Accessories
3M
PN
UPC
PN
Description
Size (in)
28473 28473
Roloc™ Cool Running Disc Pad for
5/8-11 Spindle
4 x 5/8-11 INT
83489 83489
Roloc™ Disc Pad, Hard for 5/8-11
Spindle
4 x 5/8-11 INT
83980 83980
Roloc™ Disc Pad, Extra Hard for
5/8-11 Spindle
4 x 5/8-11 INT
See 3M ASD Accessories to Optimize Performance catalog 61-5002-8098-9
and Engineered Metalworking Solutions catalog 61-5002-8097-1 for
additional accessories.
Figure 1
Closed Loop Pipe System
Sloped in the direction of air flow
Drain Leg
Ball Valve
To Tool Station
Filter
Drain Valve
Regulator
Lubricator
Ball
Valve
Ball Valve
Air Flow
Air Dryer
Air Compressor
and Tank
Air Hose
To Coupler
at or near Tool