3M 28436 Instruction Manual
Original Instructions
1
Intended Use
Important Safety Information
3
POWER SUPPLY FOR ELECTRIC TOOLS INSTRUCTION MANUAL
Alternating Current (AC) INPUT: 100 – 240 VAC 47-63 Hz.
Direct Current (DC) OUTPUT: 30 VDC 5 A
Please read, understand and follow all safety information contained in these instructions prior to the use of this Power Supply. Retain these instructions for future
reference.
The 3M Power Supply Model 28436 is intended for use in industrial locations, and used only by skilled, trained professionals in accordance with the instructions in
this manual. It is designed to be used with 3M Electric Power tools. Used in any other manner or with other power tools could lead to unsafe operating conditions.
Do not operate Power Supply in an excessively damp or wet application.
Explanation of Signal Word Consequences
Indicates a potentially hazardous situation which, if not avoided, may result in death or serious injury
and/or property damage.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury and/or property damage.
Indicates a potentially hazardous situation, which, if not avoided, may result in property damage.
WARNING:
CAUTION:
Notice:
Summary of device labels containing safety information
Symbol
Description
Symbol
Description
Underwriters Laboratories, Inc., United States and Canada
VAC
Volts Alternating Current
VDC
Volts Direct Current
Hz
Hertz
A
Amper
WARNING: read all safety warnings and instructions
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS – this Operator’s Manual contains important safety and operating instruction for 3M Power Supply.
To reduce the risk of injury. Operate the 3M Electric power tool with the 3M Power Supply. Other types of power supplies may cause personal injury or
damage.
Avoid dangerous environments. Do not operate the tool or Power Supply in rain, snow, damp or wet locations. Do not use Power Supply in the presence of
explosive atmospheres (gaseous fumes, dust or flammable materials) because sparks may be generated when inserting or removing attached tool, possibly
causing fire.
Maintain power cords and cables. When unplugging AC power cord, pull plug rather than cord to reduce the risk of damage to the electrical plug and cord.
Never carry Power Supply by its cord. Keep cord from heat, oil and sharp edges. Make sure cord will not be stepped on, tripped over or subjected to damage or
stress. Do not use Power Supply with damaged cord or plug. Have a damaged cord replaced immediately.
Do not use an extension cord unless it is absolutely necessary. Using the wrong, damaged or improperly wired extension cord could result in the risk of fire
and electrical shock. If an extension cord must be used, plug the Power Supply into a properly wired 18 AWG or larger extension cord with pins that are the same
number, size and shape as the pins of the power supply cord. See table below. Make sure that the extension cord is in good electrical condition.
Tool Current
EXTENSION Cord Length ft (m)
25 (7.6)
50 (15.2)
75 (22.8)
100 (30.4)
0 – 6 A
(mm 2)
18 AWG
(1.0)
16 AWG
(1.5)
16 AWG
(1.5)
14 AWG
(2.5)
Power Supply is rated for 100-240 Volt AC only (Evaluated @ 100-120 Volt AC only for U.S. and Canada). Power Supply must be plugged into an appropriate
receptacle.
Unplug Power Supply when not in use. Remove Electric tool from the unplugged Power Supply.
To reduce the risk of electric shock. Always unplug Power Supply before cleaning or maintenance. Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock
hazards.
Do not crush, drop or damage Power Supply. Do not use a Power Supply that has received a sharp blow, been dropped, run-over, or damaged in any way (e.g.
pierced with a nail, hit with a hammer, stepped on).
Do not disassemble. Incorrect reassembly may result in the risk of electric shock or fire. If it is damaged, return to 3M for service.
SAFETY WARNINGS