3M Digital Projector X30 Product Warranty And Safety Manual - Warning

3M™ Digital Projector X30 Product  Warranty and Safety Guide

8

ENGLISH

© 3M 2009. All rights reserved.

‡ 7RUHGXFHWKHULVNDVVRFLDWHGZLWKFKRNLQJ

- 

Keep the battery away from children and pets.

‡ 7RUHGXFHWKHULVNDVVRFLDWHGZLWKH[SRVXUHWRKD]DUGRXVYROWDJH

- 

Disconnect power cord when the projector is not in use, during lamp 

replacement, and while cleaning.

 'RQRWUHPRYHDQ\VFUHZVRWKHUWKDQWKRVHVSHFL¿HGLQWKHODPSUHSODFHPHQW

instructions.

- 

Do not store or operate this projector in wet environments.

- 

Do not modify this projector.

- 

Do not attempt to service the projector - there are no user serviceable parts, 

other than the lamp cartridge, inside the projector. Contact a 3M authorized 

service provider for service.

- 

Do not allow water or other liquids to enter the projector.

‡ 7RUHGXFHWKHULVNDVVRFLDWHGZLWKHQYLURQPHQWDOFRQWDPLQDWLRQGXHWR

mercury in the projection lamp:

-

Dispose of lamp cartridge in accordance with applicable federal, state and local regulations.

-

The lamp in this product contains mercury. Dispose of projection lamp in a manner 

that is consistent with your local hazardous waste regulations for mercury.

-

For recycling and disposal information, contact your respective governmental 

agencies.

In U.S., contact 1-800-328-1371 (3M US) or the Electronic Industries Alliance at 

www.lamprecycle.org

In Canada, contact 1-800-364-3577 (3M Canada)

‡ 7RUHGXFHWKHULVNDVVRFLDWHGZLWKH[SRVXUHWRKD]DUGRXVYROWDJHDQGRU¿UH

- 

Replace power cord if damaged.

- 

Contact a 3M authorized service provider if the projector becomes damaged.

- 

Use a grounded extension cord with a rating at least equal to that of the projector.

- 

Connect this projector to a grounded outlet.

‡ 7RUHGXFHWKHULVNDVVRFLDWHGZLWKKD]DUGRXVYROWDJHLPSDFWWULSSLQJDQG

intense visible light:

- 

Do not use this projector around unsupervised children.

‡ 7RUHGXFHWKHULVNDVVRFLDWHGZLWKKRWVXUIDFHRIODPSFDUWULGJH

- 

Unplug the projector from the electrical outlet and allow the lamp to cool for 45 

minutes before replacing the lamp.

‡ 7RUHGXFHWKHULVNDVVRFLDWHGZLWKDUXSWXUHGODPS

- 

Always handle the fragile lamp module with care.

- 

Remove the projector from the ceiling or wall mount before replacing the lamp.  

- 

Use care when replacing the lamp module in the event of a lamp rupture - small 

glass particles and small amounts of mercury may be present.

- 

Ventilate the area where the lamp rupture occurred.

- 

Wear safety goggles and gloves when cleaning up ruptured lamp debris.

- 

Carefully collect the ruptured lamp debris in a closed container and dispose of 

the container and the expired lamp module in accordance with federal, state, 

and local regulations.

- 

Wash your hands thoroughly after handling ruptured lamp debris.

- 

Replace the lamp module when the lamp replacement message appears.

- 

Never replace the lamp module with a previously used lamp module.

WARNING