3M Overhead Projector 1600 Series Operator's Manual - Warning
© 3M 2005. All Rights Reserved.
2
3M™ Overhead Projector 1600 Series
WARNING
English
To reduce the risk of various hazards associated with this product:
-
Read, understand, and follow all safety information contained in this “Important Safety Instructions” prior to using this overhead
projector. Always ensure that the equipment is used safely. Retain these instructions for future reference.
-
Close supervision is necessary when this projector is used by or near children. Do not leave projector unattended while in use.
-
The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock or injury to
persons.
To reduce the risk associated with hazardous voltage and/or fire:
-
Always switch power off and unplug projector from electrical outlet before cleaning and servicing and when not in use. Never yank
cord to pull plug from outlet. Grasp plug and pull to disconnect.
-
Do not operate projector with a damaged cord or if the appliance has been dropped or otherwise damaged – until it has been
examined by a qualified service technician.
-
Service/repair or maintenance must only be performed by qualified service personnel. Do not disassemble this appliance yourself;
incorrect reassembly can cause electric shock when the projector is used subsequently.
-
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. Cords rated for
less amperage than the projector may overheat.
-
Connect this projector to a grounded outlet.
-
Do not immerse this projector in water or other liquids.
-
Replace failed fuse only with the same type and rating as specified on fuse label.
-
Never store the power cord or any other articles inside the projector's enclosure.
-
Disconnect this projector from its source of supply before replacing the projection lamp or performing any other service.
CAUTION
To reduce the risk of various hazards associated with this product:
-
Position the projector's cord so that it will not be tripped over, pulled, or contact hot surfaces. The socket outlet must be installed near
the equipment, and easily accessible.
-
Do not expose this projector to direct sunlight; also do not use outdoors or in other wet environments.
-
Always operate projector on a flat, sturdy surface.
To reduce the risk associated with hot surfaces produced by the projection lamp:
-
Never touch the projection lamp or surrounding surfaces while the lamp is still hot.
-
Switch unit off "0", remove the power cord from the electrical outlet, and allow the unit to cool completely before replacing the lamp.
-
Let projector cool completely before putting away. Loop cord loosely around appliance when storing.
To reduce the risk associated with pinching and/or piercing:
-
Use care when opening or closing glass platten (top cover) to ensure it does not fall uncontrollably.
-
Keep hands away from the interlock actuator located on the top cover when closing.
To reduce the risk associated with sharp glass fragments:
-
Use care when removing lamp glass that has failed and shattered into sharp pieces.
-
Use care when removing glass from a broken projection lens.
To reduce the risk associated with muscular strain:
-
Weight of projector is approximately 30 Lbs (13.6 Kg); utilize the built-in handles and proper lifting technique when lifting this
projector. Never lift projector by its foldable arm.
To reduce the risk associated with high temperatures and/or related fire:
-
Replace failed lamp only with type specified on lamp label.
Important Notes
The appliance switch is provided with the symbols "O" indicating OFF, and "I" indicating ON.
Keep ventilation openings free of any obstructions.
Let overhead projector cool completely before putting away. Store the power cord so that it will not be damaged.
Care must be taken to ensure the smooth airflow of the cooling system. Immediately switch off the machine if the fan is not functioning
properly.
Make sure that the operating voltage of the overhead projector corresponds to your local voltage.
Do not use detergents, chemicals, or any spray liquids for cleaning this unit, other than those referred to in the “Operators Guide”.
SAVE THESE INSTRUCTIONS
The 3M logo and 3M are a trademark of 3M company.