1. DL manuals
  2. 3W
  3. Toy
  4. Xtra Fun II 230
  5. Assembly Manual

3W Xtra Fun II 230 Assembly Manual

Summary of Xtra Fun II 230

  • Page 1

    Xtra fun ii 230 a s s e m b l y m a n u a l 3w-modellmotoren gmbh specifications: wingspan: 90.5in length: 92.5in weight: 17.6 - 18.7lb engine: 3w 55i radio: four channel type: aerobatic / 3d.

  • Page 2

    Dear model airplane pilot, we are pleased with your decision for our new xtra fun ii. The xtra fun ii is a consistent advancement of the predecessor model. Together with roland and wolfgang matt we improved different details further: the horizontal tail unit is now profiled and of plug-in-design. Th...

  • Page 3

    Kit content............................................................................................ 4 combo version content......................................................................... 5 required radio, engine ........................................................................ 6...

  • Page 4

    Parts list: • fuselage • rudder • elevator le / ri, tube, protection bag • wings le / ri, tube, protection bag • canopy • cowling • landing gear • wheel cover • tail wheel assembly • spinner incl. Screw m5x60 xtra fun ii 230 kit contentt 4 small parts: rudder • 1 x control horn • 2 x clevis 3mm • 2 ...

  • Page 5

    • engine 3w 55i incl. Ignition, • carburetor, exhaust sealing and manual • muffler - size l • exhaust manifold - s shaped • teflontube 24,5mm • 2x hose clamp 24,5mm • tank 500ccm • propeller additionally to the standard design the combo version contains : muffler mounting see picture ignition • 2 x ...

  • Page 6

    Glues • pva • uhu endfest 300 • screw locking medium strong engine / ignition • engine minimum 2.92 cu.In • parts from combo version • ignition battery • switch ignition additionally to the parts contained in the component system you need: rc components: • receiver / five channels • 4 x servo ailero...

  • Page 7

    Landing gear fasten the main landing gear with enclosed screw and washers to the fuselage. Glue aluminum parts in the wheel shoe with uhu plus. Check the position of the wheel pants before. Tail wheel assembly all bolt connections must become secured with a screw locking medium strong. The wheel fit...

  • Page 8

    Attach the provided tension ring m3 and adjust the tail wheel in such a way that it can be moved freely each position. Without too much play. The screw m2 x 20 is pivoted into the ball. Afterwards you bore a hole from downside in the rudder and stick the ball with pva. File a notch into the steel wi...

  • Page 9

    With the two screws m4 x 18 and washers the gear is fastened to the fuselage. Glue hinges sand hinges before glueing with rough sandpaper on both sides. Use pva as adhesive. Align hinges at a straight border before drying. Xtra fun ii 230 landing gear / hinges 9.

  • Page 10

    Tail unit fasten the rudder horns in such a way that they form an alignment with the servo lever. Servo installation rudder and elevator right. Wings clevis at wing interior clevis at wing exterior bond the hinges as into part iii. Focus on absolute accurate alignment. Inaccuracies lead to function ...

  • Page 11

    Afterwards the flexible muffler mounting is installed. Make connection between exhaust manifold and wuffler with teflon pipe and the two spring clips. Engine and muffler screw engine with 4 screws m5 x 25 to the motordom. Use screw locking medium strong. Use circlips for fixing exhaust manifold. Ins...

  • Page 12

    Cowling glue provided wood parts at the head frame. Fix the cowling accurately on the fuselage with adhesive tape. Measure boreholes and bore with drill 2.5 mm. Pay attention to sufficient distance between cowling and exhaust manifold (if necessary cut it out). Cut cylinder opening into cowling. The...

  • Page 13

    Rc system / center of gravityt before fixing the remaining rc and ignition parts, place the components in the fuselage for a test, in order to get the correct cg. Attention: for placing the components take care on your engine and ignition manual protect receiver with foam rubber or similar against v...

  • Page 14

    Programming rc we recommend the use of a modern computer system. Here we recommend the following order of programming to you: servo directions • elevator highly - pull / down - press • rudder right - left • aileron right: re high - le down left: le high - re down • throttle idle - full throttle rate...

  • Page 15

    Check before maidenflight: • let an experienced model builder verify assembly, attitudes and center of gravity.. • fill the tank with fuel according to manufacturers recommendation. • break in engine according to operating instructions and adjust both needles. • load all ignition and receiver batter...

  • Page 16

    Guarantee conditions we grant a two year warranty on our flight models. This warranty is limited to construction and/or production defects like e.G. Incorrect material or glueings, because a monitoring of accurate assembly, enterprise and maintenance of the model is not possible. Xtra fun ii 230 gua...