- DL manuals
- 909
- Saw
- BN210
- Instruction manual
909 BN210 Instruction manual
Summary of BN210
Page 1
Black cyan magenta yellow code: bn210 date: 110304 edition: 04 op: dcr instruction manual bn210 1400w 210mm (8 1/4" ) compound mitre saw.
Page 2: Warranty Power Tools
Contents warranty power tools for full details please visit us at www.909.Com 2 warranty 2 introduction 3 environmental protection 3 description of symbols 3 specifications 3 general safety rules 4 additional safety rules for mitre saws 5 accessories 7 know your product 8 unpacking 9 transportation ...
Page 3: Description Of Symbols
3 description of symbols the rating plate on your tool may show symbols. These represent important information about the product or instructions on its use. Wear hearing protection. Wear eye protection. Wear breathing protection. Double insulated for additional protection. Conforms to relevant safet...
Page 4: General Safety Rules
4 general safety rules warning. Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains...
Page 5
5 4) power tool use and care a) do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. B) do not use the power tool if the switch does not turn it on and off. Any power tool that can...
Page 6
6 • ensure that the machine is always fixed to a bench, whenever possible. • always stand to one side when operating the saw. • never use a cracked or distorted saw blade. • when cutting round wood, use clamps that prevent the workpiece from turning on both sides of the blade. • never use your hands...
Page 7: Accessories
7 warning. We recommend the use of a residual current device with a residual current rating of 30ma or less. Wear goggles wear ear muffs wear a breathing mask accessories the 909 bn210 compound mitre saw is supplied with the following accessories as standard: • saw blade (fitted) • 6mm hex key • dus...
Page 8: Know Your Product
8 know your product before using the saw, familiarise yourself with all the operating features and safety requirements. 1. Saw arm 2. Release knob 3. Operating handle 4. Upper fixed blade guard 5. Rotating blade guard 6. Guard retraction arm 7. Bevel lock 8. Bevel scale 9. 45° bevel adjustment screw...
Page 9: Unpacking
9 unpacking due to modern mass production techniques, it is unlikely that your 909 power tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal...
Page 10: Mitre Table Locks
10 mitre table locks the mitre table locks (15) are used to lock the table at the desired mitre angle (fig. D1 - d2). The mitre saw cuts from 0° to 45° both left and right. To adjust the mitre angle loosen the mitre table locks and rotate the mitre table to the desired position. The mitre table feat...
Page 11
11 setting the table square with the blade 1. Make sure that the electrical plug is removed from the power point. 2. Push the saw arm (1) down to its lowest position and engage the release knob (2) to hold the saw arm in the transport position. 3. Loosen the mitre locks (15). 4. Rotate the table (12...
Page 12: Changing A Blade
12 setting the fence square with the table 1. Make sure that the electrical plug is removed from the power point. 2. Push the saw arm (1) down to its lowest position and engage the release knob (2) to hold the saw arm in the transport position. 3. Loosen the mitre locks (15). 4. Rotate the table (12...
Page 13: Operation
13 7. Hold the rotating guard (5) up and press the spindle lock button (18). Rotate the blade until the spindle locks (fig. T). 8. Use the 6mm hex key provided to loosen and remove the blade bolt. (loosen in a clockwise direction as the blade screw has a left hand thread) (fig. U). 9. Remove the fla...
Page 14: Bevel Cut
14 warning. Be sure to tighten the mitre locks before making a cut. Failure to do so could result in the table moving during the cut and cause serious personal injury. 5. Place the workpiece flat on the table with one edge securely against the fence (11). If the board is warped, place the convex sid...
Page 15: Compound Mitre Cut
15 compound mitre cut a compound mitre cut involves using a mitre angle and a bevel angle at the same time. It is used in making picture frames, to cut mouldings, making boxes with sloping sides and for roof framing. Always make a test cut on a piece of scrap wood before cutting into the good materi...
Page 16
16.