Summary of PS26W
Page 1
Instruction manual ps26w 26cc pole trimming saw.
Page 2: Warranty Power Tools
2 contents warranty power tools for full details please visit us at www.909.Com warranty 2 introduction 3 environmental protection 3 specifications 3 description of symbols 3 general safety instructions 4 additional safety instructions for the inbuilt battery pack 5 additional safety instructions fo...
Page 3: Description Of Symbols
3 description of symbols the rating plate on your tool may show symbols. These represent important information about the product or instructions on its use. Conforms to relevant safety standards. Wear hearing protection. Wear eye protection. Wear head protection. Read these instructions for use care...
Page 4: Power Tools
4 general safety instructions for handling power tools warning: read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. This unit may not be used by people (including children) with reduced physical, sen...
Page 5: Inbuilt Battery Pack
5 • dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. • if devices are provided for the connection of dust extraction and collection facilities, ensure these are co...
Page 6
6 • never attempt to open the inbuilt battery pack for any reason. If the plastic housing of the battery pack breaks open or cracks, immediately discontinue its use and do not recharge it. • the inbuilt battery pack utilizes nickel-cadmium cells. Cadmium is considered to be a toxic material. Use an ...
Page 7: Danger!
7 • do not use the tip section of the chain and bar. Kickback can occur in these conditions. • keep your eyes not only on the branches you are cutting, also keep an eye on the ground to prevent tripping over branches that already have fallen. • always wear gloves when handling the pole saw chain. Da...
Page 8: Know Your Product
8 25 22 33 21 14 11 20 27 12 17 1. Motor housing 2. On/off switch 3. Oil mix container 4. Throttle trigger 5. Safety lever 6. Main handle 7. J handle 8. Shoulder strap 9. Upper shaft 10. Lower shaft 11. Shaft pin lock 12. Chain bar 13. Blade cover 14. Throttle lock button 15. Oil tank 16. Tube spann...
Page 9: Assembly
9 assembly this product is partially assembled. Prior to use, it is necessary to assemble/fit the upper shaft (9), lower shaft (10), j handle (7), chain (17) and chain bar (12). Fitting the chain and chain bar 1. Remove the chain drive cover nut (20) with the spanner supplied (29) and remove the cha...
Page 10: Connecting The Lower
10 connecting the j handle to the upper shaft 1. Lay the pole saw upper shaft down so that the petrol tank is resting on a secure surface, or on the ground. 2. Insert both of the mounting screws (+ one flat washer) through the mounting bracket, with one of the screws going through the screw hole in ...
Page 11: Mixing The Fuel
11 setting the oil adjustment screw the pole saw has an adjustment to vary the oil flow to the chain. During manufacturing, this has been set to maximum. There are 3 settings; max, med, and low. The setting can be adjusted by: 1. Insert the flat bladed section of the screwdriver supplied into the he...
Page 12: Filling The Tank
12 filling the tank warning. Always shut off the engine before fuelling. Never add fuel to a machine with a running or hot engine. Move at least 10m away from the refuelling site before starting engine. Do not smoke when refuelling or operating the line trimmer. Note . It is normal for smoke to be e...
Page 13: Warm Start
13 5. Check the ignition on / off switch is on. (i pressed down) pull the recoil starter until you hear the engine starting or trying to start. (under full choke it may only run for 1 or 2 seconds). Do not keep trying to start the motor or you will flood the motor. Move the red choke lever downwards...
Page 14: Stopping The Pole Saw
14 stopping the pole saw 1. Release pressure to the throttle trigger (4) and allow the engine to idle for a few moments. 2. Move the ignition switch (2) to the off position marked o. Running in the engine 1. During the first 2–3 hours of work, run the engine at a moderate rpm. 2. We advise you in an...
Page 15: Pole Saw Maintenance
15 working with the pole saw do not work with an angle higher than 60°. The pole saw will work under higher degrees, but there is the danger of being injured by branches falling without warning. Keep an eye at the ground while working to avoid tripping over fallen branches. Never use the pole saw wi...
Page 16: First Time User
16 dust. Wear safety glasses to protect your eyes whilst cleaning. • if the body of the saw needs cleaning, wipe it with a soft damp cloth. A mild detergent can be used but nothing like alcohol, petrol or other cleaning agent. • never use caustic agents to clean plastic parts. • turn the bar periodi...
Page 17
17.
Page 18
18.
Page 19
19.
Page 20
20