1. DL manuals
  2. 909
  3. Impact Driver
  4. T12ID4
  5. Instruction Manual

909 T12ID4 Instruction Manual

Summary of T12ID4

  • Page 1

    Environmental protection 1 description of symbols 1 know your tool 2 specifications 2 operating instructions 3 battery & charging procedure 3 tsg, sleep mode, activating tool, forward/reverse, variable speed 4 led worklight, power consumption led belt clip, temperature & low voltage cut out, hex chu...

  • Page 2: Specifications

    2 for further detailed up to date specifications and for warranty details, visit our website at 909.Com specifications motor: 12 v impact driver / wrench speed: 0 - 2300 min -1 impact rate: 3000 bpm max. Torque: 100nm, 885 in-lbs chuck collet hex: 6.35mm (1/4) battery: tb12 series lithium-ion model ...

  • Page 3: Operating Instructions

    3 operating instructions warning! • do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is enough to cause serve injury. • before attempting to use this cordless impact driver, become familiar with all of its operating features and safety requireme...

  • Page 4: Touch Sensor Grip  (Tsg)

    4 touch sensor grip power tool congratulations on purchasing a touch sensor grip (tsg) power tool. The tsg system incorporates a fully electronic control system which operates the tool on pressure applied to the touch area, instantaneously allowing operation between forward and reverse. Tools fitted...

  • Page 5: Led Worklight

    5 led worklight when the unit is switched on, the led worklight also comes on to ensure better vision and to make working in dark areas safer. The worklight goes out when the tsg system is released. Power consumption led this led indicates the amount of battery power available for your task. At acti...

  • Page 6: Tightening Torque

    6 inserting a driver or nut setter bit into the impact driver attachment warning! Do not insert or remove bits while the tool is activated. Make sure the battery pack is removed or the tool is in sleep mode when inserting or removing bits. 1. Your tool is equipped with a quick release chuck. To inse...

  • Page 7: Running Nuts And Bolts

    7 running nuts and bolts variable speed control must be used with caution for driving nuts and bolts with socket set attachments. The technique is to start slowly, increasing speed as the nut or bolts run down. Set the nut or bolt snugly by allowing the impact driver to impact the nut to the desired...

  • Page 8

    8 • do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. • dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can...

  • Page 9: The Battery/charger

    9 • secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand. • keep your workplace clean. Blends of materials are particularly dangerous.Dist from light alloys can burn or explode. • do not open the battery. Danger of short-circuiting. • in case ...

  • Page 10: Work Area Safety

    10 your risk from these exposures varies, depending upon how often you do this type of work. To reduce your exposure to these chemicals: • work in a well-ventilated area. • work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles. • avoi...

  • Page 11: Power Tool Use and Care

    11 power tool use and care • do not force the power tool. Use the correct power tool for your application. The correct power tool will do a better and safer job if used for the function it was designed for. • do not use the power tool if the switch does not turn it on and off. Any power tool that ca...

  • Page 12: General Maintenance

    12 specific safety rules for cordless drill/driver • hold power tool by insulated gripping surface when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will also make exposed metal parts on the tool “live” and shock the operator. •...

  • Page 13: Batteries

    13 air to clean the tool. If the operation is dusty, also wear a dust mask. • do not at any time allow brake fluids,gasoline, petroleum - based products, penetrating oils,etc, to come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal ...

  • Page 14: Parts List

    14 parts list if any parts are missing or damaged, or if you have any questions, please email us at info@909.Com.

  • Page 15: Other Models Available:

    15 other models available: 12v drill/driver.

  • Page 16

    909powertools w: 909.Com e: info@909.Com © globalpowerbrands international p/l 2013.