Fz-i / fx-i series fz-120i / fz-200i /fz-300i /fz-500i fz-1200i / fz-2000i /fz-3000i /fz-5000i fx-120i / fx-200i /fx-300i /fx-500i fx-1200i / fx-2000i /fx-3000i /fx-5000i precision balance 1wmpd4001863b instruction manual.
? 2011 a&d company ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, or translated into any language in any form by any means without the written permission of a&d company ltd. The contents of this manual and the specifications of the instrument cover...
1 contents basic operation 1. Introduction .............................................................................................................................3 1-1 about this manual................................................................................................................
2 functions 10. Function table .....................................................................................................................36 10-1 structure and sequence of the function table .............................................................................. 36 10-2 display and ...
3 1. Introduction this manual describes how the fz-i / fx-i series balance works and how to get the most out of it in terms of performance. Read this manual thoroughly before using the balance and keep it at hand for future reference. 1-1 about this manual this manual consists of the following five ...
4 1-3 compliance compliance with fcc rules please note that this device generates, uses and can radiate radio frequency energy. This device has been tested and has been found to comply with the limits of a class a computing device pursuant to subpart j of part 15 of fcc rules. These rules are design...
5.
6.
7 ac adapter ac adapter id label rs-232c serial interface main unit rear side ac adapter jack grounding terminal ac adapter plug keys weighing pan main unit display bubble spirit level leveling foot pan support main unit cover how to assemble the breeze break (for the fz-i series (all) andfx-120i/20...
8 2-2 installing the balance install the balance as follows: 1. Place the balance on a solid weighing table. Refer to “3. Precautions” for installing the balance. 2. The fz- i series (all) andfx-120 i /200 i /300 i /500 i assemble the pan support, weighing pan and breeze break, on the balance as sho...
9 3. Precautions to get the optimum performance from the balance and acquire accurate weight data, note the following: 3-1 before use install the balance in an environment where the temperature and humidity are not excessive. The best operating temperature is about 20°c / 68°f at about 50% relative ...
10 this balance uses a strong magnet as part of the balance assembly, so please use caution when weighing magnetic materials such as iron. If there is a problem, use the underhook on the bottom of the balance to suspend the material away from the influence of the magnet. Eliminate the temperature di...
11 4. Display symbols and key operation key operation key operation affects how the balance functions. The basic key operations are: “press and release the key immediately” or “press the key” = normal key operation during measurement “press and hold the key” display symbols each key, when pressed or...
12 5. Weighing units 5-1 units with the fz-i / fx-iseries balance, the following weighing units and weighing modes are available: a unit or mode can be selected and stored in the function table as described on page 14. If a weighing mode (or unit of weight) has been turned off, that mode or unit wil...
13 the tables below indicate the weighing capacity and the minimum display for each unit, depending on the balance model. Capacity unit fz-120 i fx-120 i fz-200 i fx-200 i fz-300 i fx-300 i fz-500 i fx-500 i minimum display gram 122.000 220.000 320.000 520.000 0.001 ounce (avoir) 4.30340 7.76025 11....
14 5-2 storing units the units or modes can be selected and stored in the function table. The sequence of displaying the units or modes can be arranged in the function table so as to fit the frequency of use. Select a unit or mode and arrange the sequence of display as follows: 1 press and hold the ...
15 6. Weighing 6-1 basic operation (gram mode) 1 place a container on the weighing pan, if necessary. Press the re-zero key to cancel the weight (tare). The balance displays 0.00 g. (the decimal point position depends on the balance model.) 2 place a sample on the pan or in the container. 3 wait for...
16 6-2 counting mode (pcs) this is the mode to determine the number of objects in a sample based on the standard sample unit mass. The unit mass means the mass of one piece of the sample. The smaller the variables in each sample unit mass are, the more accurate the counting will be. The balance is e...
17 notes if the balance judges that the mass of the samples is too light and is not adequate to be used as the unit mass, it displays lo . In that case, store the mass by some quantity. For example, when the model with the minimum weighing value of 0.01 g is used and 10 pieces of samples weigh 0.05 ...
18 6-3 percent mode (%) this is the mode to display the weight value in percentage compared to a 100% reference mass and is used for target weighing or checking the sample variable. Selecting the percent mode 1 press the mode key to select % (percent mode). Storing the 100% reference mass 2 press th...
19 6-4 statistical calculation mode the statistical calculation mode statistically calculates the weight data, and displays or outputs the results. To use the statistical calculation mode, set the "application function (apf)" parameter of “application (ap fnc)” in the function table to “2”, as descr...
20 selecting the statistical items to output 5 press the sample key to display 5taf 0 . 6 press the re-zero key to select the output items. In the example, 5taf 1 is selected to output the number of data, sum, maximum, minimum, range (maximum-minimum) and average. Parameter description 0 number of d...
21 1 press the re-zero key to set the display to zero. 2 place the sample on the weighing pan and wait for the stabilization indicator to turn on. 3 press the print key to add the data displayed to statistical calculation. The number of data on the upper left of the display increases by 1. 4 repeat ...
22 n010 n009 sum deleting the latest data when the wrong data is entered, it can be deleted and excluded from statistical calculation. Only the latest data can be deleted. 1 in the weighing mode, press the mode key, and then press the sample key to display 1 cancel . 2 press the print key to display...
23 6-5 statistical calculation mode (example of use) here, as an example of use of the statistical calculation mode, mixing of the multiple formulae such as medicine is described. The mixing process is recorded using the balance and the printer. In the example, the fx-3000i and the ad-8121b (dump pr...
24 5-5-2 using the statistical calculation mode 1 press the re-zero key to set the display to zero. 2 place a container on the weighing pan. Press the print key to cancel the weight (tare). The balance displays 0.00 g. (storing the tare value) the tare value data is output when the peripheral output...
25 7. Response adjustment this function stabilizes the weight value, reducing the influence on weighing that is caused by drafts and vibration at the place where the balance is installed. The function has three stages as follows and can be changed by simple key operation. Indicator description fast ...
26 8. Calibration 8-1 calibration mode the balance has the following modes. Calibration using the internal mass (one-touch calibration, only for the fz-iseries) calibration using an external weight calibration test using an external weight (calibration test does not perform calibration.) terms the f...
27 8-2 calibration using the internal mass (one-touch calibration, only for f z - i series ) this function calibrates the balance using the internal mass. The only operation required is to press the cal key note level the balance by adjusting the leveling feet and confirm that the bubble is in the c...
28 8-3 correcting the internal mass value: 1 (only for fz-i series) the fz-i series balance can correct the internal mass value using an external weight. Method 1: calibrate the balance using the internal mass. Measure the external weight. Calculate the correction value. And store it in the balance....
29 8-4 correcting the internal mass value: 2 (only for fz-i series) z the fz-i series balance can correct the internal mass value using an external weight. Method 2: calibrate the balance using the external weight. The balance performs automatic calibration using the internal mass, corrects the inte...
30 8-5 calibration using an external weight this function calibrates the balance using an external weight. Operation 1 connect the ac adapter and warm up the balance for at least 30 minutes with nothing on the pan. 2 press and hold the cal key until calout is displayed, and then release the key. 3 t...
31 5 confirm that there is nothing on the pan and press the print key. The balance measures the zero point. Do not allow vibration or drafts to affect the balance. The balance displays the calibration weight value. 6 place the displayed calibration weight on the pan and press the print key. The bala...
32 8-6 calibration test using an external weight this function tests the balance weighing accuracy using an external weight and outputs the result. This is available only when the “glp output (info)” parameter is set to “1” or “2”. (calibration test does not perform calibration.) operation 1 connect...
33 5 confirm that there is nothing on the pan and press the print key. The balance measures the zero point and displays the measured value. Do not allow vibration or drafts to affect the balance. The balance displays the target weight value. 6 place the displayed target weight on the pan and press t...
34 9. Function switch and initialization 9-1 permit or inhibit the balance stores parameters that must not be changed unintentionally. There are two switches for the purpose of protecting these parameters. Each switch can select either “permit” or “inhibit”. The “inhibit” protects parameters against...
35 operation 1 press the on:off key to turn off the display. 2 while pressing and holding the print key and the sample key, press the on:off key. The balance displays p5 . 3 press the print key. Then the balance displays the function switches. 4 set the switches using the following keys. Sample key ...
36 10. Function table the function table reads or rewrites the parameters that are stored in the balance. These parameters stored, even if the ac adapter is removed, are maintained in non-volatile memory. 10-1 structure and sequence of the function table the function table menu consists of two layer...
37 10-3 details of the function table class item and parameter description 0 fast response, sensitive value fast 1 mid. Cond condition 2 slow response, stable value slow with “hold 1”, sets the averaging time. 0 stable range is ±1 digit 1 5t-b stability band width 2 stable range is ±3 digits the sta...
38 class item and parameter description cp hi upper limit cp lo lower limit refer to “10-10 comparator function”. 0 key mode accepts the print key only when the display is stable. 1 auto print mode a (reference = zero) 2 auto print mode b (reference = last stable value) outputs data when the display...
39 class item and parameter description 0 600 bps 1 1200 bps 2 2400 bps 3 4800 bps 4 9600 bps bp5 baud rate 5 19200 bps 0 7 bits, even 1 7 bits, odd btpr data bit, parity bit 2 8 bits, none 0 cr lf crlf terminator 1 cr cr: ascii code 0dh lf: ascii code 0ah 0 a&d standard format 1 dp format 2 kf form...
40 10-4 description of the class “environment, display” condition ( cond ) cond 0 this parameter is for sensitive response to the fluctuation of a weight value. Used for powder target weighing, weighing a very light sample or when quick response weighing is required. After setting, the balance displ...
41 zero tracking ( trc ) this function tracks zero point drift caused by changes in the environment and stabilizes the zero point. When the weight data is only a few digits, turn the function off for accurate weighing. Note digit indicates a unit of minimum weighing value. Trc 0 the tracking functio...
42 10-5 description of the item “data output mode” the parameter setting of the “data output mode ( prt )” applies to the performance when the data is transmitted using the rs-232c serial interface. Key mode when the print key is pressed with the stabilization indictor turned on, the balance outputs...
43 interval output mode the weight data is periodically output. When the print key is pressed, the balance starts to output the weight data at a preset interval time. When the print key is pressed again, the balance stops outputting the weight data. Required setting dout prt 6 interval output mode d...
44 kf format 5if type 2 this is the karl-fischer moisture meter format and is used when the peripheral equipment can only communicate using this format. This format consists of fourteen characters excluding the terminator. This format has no header characters. The polarity sign is placed before the ...
45 date dout 5-td 2 or 3 z the date output order can be changed in "clock ( cl adj )". Z the year is output in a four-digit format. Time dout 5-td 1 or 3 z the time is output in a 24-hour format. 10-7 data format examples 1 2 : 3 4 : 5 6 cr lf cr lf positive error overload cr lf cr lf cr lf cr lf cr...
46 note when “pound ounce” is selected, the data is output with the unit of ounce (oz). 10-8 description of the item “application function” capacity indicator ( apf1) in the weighing mode, the indicator displays the weight data relative to the weighing capacity in percentage. (zero = 0%, maximum cap...
47 10-9 clock and calendar function (only for fz-i series) the fz-i series balance is equipped with a clock and calendar function. When the “glp output (info)” parameter is set to “1” or “2” and the “time/date output (5-td)” parameter is set to “1”, “2” or “3”, the time and date are added to the out...
48 confirming the time 6 the current time is displayed with all the digits blinking. When the time is correct and the date does not need to be confirmed, press the cal key and go to step 8. When the time is correct and the date is to be confirmed, press the sample key and go back to step 4. When the...
49 10-10 comparator function the results of the comparison are indicated by hi ok lo on the display. Operating conditions: no comparison comparison when the weight data is stable or overloaded, excluding “near zero” comparison when the weight data is stable or overloaded, including “near zero” conti...
50 11. Id number and glp report the id number is used to identify the balance when good laboratory practice (glp) is used. The id number is maintained in non-volatile memory even if the ac adapter is removed. The glp output format is selected at “glp output (info)” of the function table and can be o...
51 11-2 glp report set the following parameters to output the report. To print the report, set the “glp output ( info )” parameter to “1”, set the “data output pause ( pu5e )” parameter to “1” and use mode 3 of the ad-8121b. For details on using the printer, refer to “15-1 connection to the ad-8121b...
52 calibration report using an external weight when the setting is “info 1”: when the setting is “info 2”: calibration test report using an external weight (calibration test does not perform calibration.) when the setting is “info 1”: when the setting is “info 2”: ad-8121 format general data format ...
53 title block and end block when a weight value is recorded as the glp data, “title block” and “end block” are inserted at the beginning and at the end of a group of weight values, in the glp report. Note to output the report to an ad-8121b , use mode 3 of the ad-8121b. Operation 1 with the weight ...
54 12. Underhook the underhook can be used for magnetic materials or density measurement. The built-in underhook is revealed by removing the plastic cap on the bottom of the balance. Use the underhook as shown below. Caution do not apply excessive force to the underhook. When not in use, attach the ...
55 13. Programmable-unit this is a programmable unit conversion function. It multiplies the weight data in grams by an arbitrary coefficient set in the function table and displays the result. The coefficient must be within the range between the minimum and maximum shown below. If the coefficient set...
56 5 4 3 2 1 9 8 7 6 14. Rs-232c serial interface the balance is a data communication equipment (dce) device. Connect the balance to a personal computer (dte) using a straight through cable. Transmission system : eia rs-232c (d-sub 9-pin, female connector) transmission form : asynchronous, bi-direct...
57 1 2 3 4 mode on 15. Connection to peripheral equipment 15-1 connection to the ad-8121b printer set the following parameters to use the ad-8121b printer. Example of use ad-8121b mode setting to print a&d standard format weight data, using the fz-i / fx-i print key orauto print mode. (the time and ...
58 15-2 connection to a computer the balance can be connected to a personal computer using the rs-232c serial interface. As an option, the fxi –02 usb interface is available to transmit the balance data to a personal computer. The balance is a dce device. Use a straight through cable when connecting...
59 using the winct software, the balance can do the following: 1 analyzing the weight data and the statistics with “rskey” the weight data can be input directly into an excel worksheet. Then, excel can analyze the data to obtain sum, average, standard deviation, maximum and minimum value, and displa...
60 16. Commands 16-1 command list note a command has a terminator added, that is specified using the "terminator (crlf)" parameter of “serial interface ( 5if )” in the function table, and is sent to the balance. Commands to query weight data c cancels the s or sir command. Q requests the weight data...
61 16-2 acknowledge code and error codes when the “ak, error code (ercd)” parameter of “serial interface ( 5if )” is set to “1”, the balance outputs code or an error code for each command as follows: (06h) acknowledge in ascii code. When the balance receives a command to request data and can not pro...
62 cal command example (fz-i series: calibration using the internal mass) cal command example (fx-i series: calibration using an external weight) * : exc command for fz-i series * personal computer time balance cal command zero display confirmation of command receipt command completion zero display ...
63 t command example pt command example z when a communication error has occurred due to external noise, or a parity error has occurred due to transmission error, the balance transmits an error code. In this case, send the command again. 16-3 settings related to rs-232c concerning the rs-232c, the b...
64 17. Maintenance do not use organic solvents to clean the balance. Clean the balance with a lint free cloth that is moistened with warm water and a mild detergent. Do not disassemble the balance. Contact the local a&d dealer if the balance needs service or repair. Use the original packing material...
65 18-2 error codes display error code description ec, e11 stability error the balance can not stabilize due to an environmental problem. Prevent vibration, drafts, temperature changes, static electricity and magnetic fields. Refer to “3. Precautions” for details on the operating environment and “7....
66 display error code description balance internal error if this error appears persistently, contact the local a&d dealer. Ec, e00 communications error a protocol error occurred in communications. Confirm the format, baud rate and parity. Ec, e01 undefined command error an undefined command was rece...
67 19. Options note the fxi-02, fxi-08 and fxi-09 can not be used at the same time. Fxi-02 usb interface (installed in the balance, applicable os: windows 98 osr2 or later) used to transmit the balance weight data (numerical value only) uni-directionally to a personal computer via usb. Can transmit ...
68 fxi-11 large breeze break breeze break with greater height. Can be used for all models. Convenient when a large beaker or measuring cylinder is used and requires more height. Fxi-12 animal weighing pan applicable models: fz-1200i/2000i /3000i /5000i andfx-1200i/2000i /3000i /5000i used for weighi...
69 ad-8920a remote display connected to the balance using the rs-232c serial interface to display the weight data away from the balance. Ad-8922a remote controller connected to the balance using the rs-232c serial interface to display the weight data and to remotely control the balance. Analog outpu...
70 20. Specifications fz-120i fz-200i fz-300i fz-500i fz-1200i fz-2000i fz-3000i fz-5000i weighing capacity 122 g 220 g 320 g 520 g 1220 g 2200 g 3200 g 5200 g maximum display 122.084 g 220.084 g 320.084 g 520.084 g 1220.84 g 2200.84 g 3200.84 g 5200.84 g minimum weighing value (1 digit) 0.001 g 0.0...
71 fx-120i fx-200i fx-300i fx-500i fx-1200i fx-2000i fx-3000i fx-5000i weighing capacity 122 g 220 g 320 g 520 g 1220 g 2200 g 3200 g 5200 g maximum display 122.084 g 220.084 g 320.084 g 520.084 g 1220.84 g 2200.84 g 3200.84 g 5200.84 g minimum weighing value (1 digit) 0.001 g 0.01 g repeatability (...
72 21. External dimensions fz-120i /200i / 300i / 500i fx-120i /200i / 300i / 500i fz-1200i /2000i / 3000i / 5000i fx-1200i /2000i / 3000i / 5000i fz-1200i /2000i / 3000i / 5000i, the breeze break is provided as a standard accessory. Unit: mm *1: width of the opening when a clear plate is removed *2...
73 22. Terms/index terms stable value the weight data when the stabilization indicator appears. Environment ambient conditions such as vibration, drafts, temperature, static electricity and magnetic fields which affect the weighing operation. Calibration adjustment of the balance so that it can weig...
74 index keys and symbols on/off key .....................................11 sample key ....................................11 mode key ........................................11 cal key.............................................11 print key.........................................11 re-zero key.....
75 - d - data bits ...................................................56 data format..................................................39 data output mode........................................38 data output pause.......................................38 dc static eliminator ...........................
76 mt format ............................................ 39, 44 n - nu format ............................................ 39, 44 number of data..................................... 19, 39 - o - on:off key..........................................11, 35 operating environment...........................