- DL manuals
- A&D
- Scales
- SC-150KAL
- Instruction Manual
A&D SC-150KAL Instruction Manual
Summary of SC-150KAL
Page 1
S s c c / / s s e e s s e e r r i i e e s s w w a a s s h h d d o o w w n n s s c c a a l l e e s s sc-30kam / sc-60kam / sc-150kam / sc-60kal / sc-150kal se-30kam / se-60kam / se-150kam / se-60kal / se-150kal 1wmpd4002054.
Page 2
© 2010 a&d company, limited. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, or translated into any language in any form by any means without the written permission of a&d company, limited. The contents of this manual and the specifications of the instru...
Page 3: Contents
1 contents 1. Introduction .................................................................................................. 2 2. Features........................................................................................................... 2 3. Unpacking .........................................
Page 4: 1. Introduction
2 1. Introduction this manual describes how the sc/se series wash down scales work and how to get the most out of them in terms of performance. Please read this manual completely before using the scale. 2. Features the sc/se series wash down scales have the following features: dust-tight and water-t...
Page 5: 3. Unpacking
3 3. Unpacking when unpacking, check whether all of the following items are included: ● instruction manual ● sc-kal / kam series ● se-kal / kam series *pole support foot *only for the se-kam series the cable length from the base to the display is approximately 1.5 m. S s c c / / s s e e s s e e r r ...
Page 6: 4. Description of Each Part
4 4. Description of each part ● sc-kal / kam series display display pole weighing pan spirit level option slot battery cover display rear side leveling foot display knob.
Page 7
5 ● sＥ-kal / kam series display display pole weighing pan leveling foot spirit level option slot battery cover display knob display rear side.
Page 8
6 4-1. Display and symbols display symbols symbol description stable ○ turns on when the weight value is stable. Net ◄ turns on when the net weight is displayed. (the tare operation is in progress.) zero ◄ turns on when the scale shows zero. I hi i ok i lo i turns on when the comparator results are ...
Page 9
7 4-2. Switches switch description on/off switch turns the power on or off. When turned on, the scale will be automatically set to zero (power-on zero). Print switch outputs the weight value to the printer. In the setting mode, this switch is used to increase the value of the selected blinking digit...
Page 10: 5. Setting Up
8 5. Setting up 5-1. Attaching the display pole to the base sc-kal / kam series 1. Remove the weighing pan from the base. 2. Remove the 4 screws from the lower part of the display pole. 3. Insert the display pole under the base while pulling out the cable into the base and align the cable opening po...
Page 11
9 se-kal / kam series 1. Remove the weighing pan from the base. 2. Remove the 4 screws from the lower part of the display pole. 3. Insert the display pole under the base while pulling out the cable into the base and align the cable opening positions of the pole and the base. (see “3” in the illustra...
Page 12
10 5-2. Installing the scale 1. Select the place for installing the scale. Refer to “precautions on installing the scale” below. 2. Adjust the level of the base, using the spirit level and leveling feet. Confirm that the bubble is in the center of the level. The se-kam series has an extra foot at th...
Page 13
11 5-3. Installing the batteries prepare six, size d (r20p or lr20) batteries. The batteries are not included with the product. The scale can be used continuously for about 3,600 hours using alkaline batteries. When appears, replace all six batteries with new ones as soon as possible. 1. Turn the ba...
Page 14: 6. Basic Operation
12 6. Basic operation 6-1. Turning the power on and off 1. Press the on/off switch to turn the power on. All the display symbols appear and the scale waits for the weight value to become stable. After the weight value internally becomes stable, the display turns off for a moment and zero is shown wi...
Page 15
13 6-3. Basic weighing operation 1. Press the on/off switch to turn the power on. 2. Select a weighing unit using the units switch. 3. When the display doesn’t show zero, press the zero switch to set the display to zero. 4. When using a tare (container), place the container on the weighing pan, and ...
Page 16: 7. Counting Mode
14 7. Counting mode determines a unit weight (the weight of one piece) from the known pieces of samples, and calculates how many pieces are on the weighing pan using the unit weight. The unit weight is maintained even if the power is turned off. 1. Press the units switch to select “pcs”. (“pcs” = pi...
Page 17: 8. Comparator
15 8. Comparator compares the weight value with the upper and lower limit values and shows the results of the comparison by hi ok lo on the display. The formula to compare is as follows: 1 lo ok ≤ upper limit value hi select comparison conditions that suit your own application. (refer to “comparator...
Page 18
16 entering the upper and lower limit values 1. Press the units switch to select a weighing unit, ”kg”, ”lb” or ”oz” 2. Press and hold the units switch to enter the upper limit setting mode. 3. Enter the upper limit value using the following switches. Units to shift the blinking digit to the right. ...
Page 19: 9. Calibration
17 9. Calibration adjusts the scale for accurate weighing. Calibrate the scale in the following cases. When the scale is first installed. When the scale has been moved. When the ambient environment has changed. For regular calibration. 9-1. Gravity acceleration correction when the scale is first use...
Page 20
18 9-2. Calibration using a weight prepare a weight, preferably a weight with the same value as the weighing capacity of the scale to be calibrated. Note that the calibration weight value can be set by 10 kg/lb. 1. Turn the power on and warm up the scale for at least half an hour. Change the functio...
Page 21
19 9-3. Restoring to the factory setting values if the gravity acceleration value or calibration weight value is changed unintentionally, restore those values to the factory setting values, as follows. Make sure that the scale is in the weighing mode (displaying “kg”, “lb”, “oz” or “pcs”). 1. Press ...
Page 22: 10. Functions
20 10. Functions the scale has function settings to specify the scale performance. The parameters set in the function settings are maintained even if the power is turned off. 10-1. Setting the parameters 1. Turn the power off. 2. Press and hold the tare switch and press the on/off switch to turn the...
Page 23
21 10-2. Function list item parameter description 0 auto power-off disabled auto power-off function poff 1 auto power-off enabled turns the power off automatically 0 normal (1/3,000) weight display resolution r5eo 1 high (1/6,000 or 1/7,500) changes “d”, minimum display 0 2400 bps 1 4800 bps serial ...
Page 24: 11. Options
22 11. Options the following options are available for the sc/se series: op-02 (sce-02) usb interface op-03 (sce-03) rs-232c serial interface and comparator relay output note when an option is installed, the dust-tight and water-tight performance of the scale will be degraded. For details, refer to ...
Page 25: 13. Specifications
23 13. Specifications 13-1. Specifications materials weighing platform weighing pan sc series: stainless steel (sus304) stainless steel (sus304) se series: steel stainless steel (sus430) model sc-30kam se-30kam sc-60kam se-60kam sc-150kam se-150kam sc-60kal se-60kal sc-150kal se-150kal weighing capa...
Page 26
24 13-2. External dimensions ● sc-30kam / sc-60kam / sc-150kam ● sc-60kal / sc-150kal unit: mm 60 11 7 163 380 38.1 173 300 71 7 220 300 60 158 530 38.1 173 440 12 3 71 7 390 300
Page 27
25 ● se-30kam / se-60kam / se-150kam ● se-60kal / se-150kal unit: mm 60 11 8 300 202 380 202 72 2 300 220 40 60 440 12 8 530 202 300 390 72 2 40
Page 28: Gravity Acceleration Map
26 gravity acceleration map values of gravity at various locations amsterdam 9.813 m/s 2 manila 9.784 m/s 2 athens 9.807 m/s 2 melbourne 9.800 m/s 2 auckland nz 9.799 m/s 2 mexico city 9.779 m/s 2 bangkok 9.783 m/s 2 milan 9.806 m/s 2 birmingham 9.813 m/s 2 new york 9.802 m/s 2 brussels 9.811 m/s 2 ...
Page 29
27 world map.