1. DL manuals
  2. A-Neu Video
  3. Matrix Switcher
  4. ANI-1082UHD
  5. Instruction Manual

A-Neu Video ANI-1082UHD Instruction Manual

Manual is about: 10x10 HDMI and HDBaseT Matrix with Audio Matrixing & LAN

Summary of ANI-1082UHD

  • Page 1

    Audio / video manufacturer ani-1082uhd 10x10 hdmi and hdbaset ™ matrix with audio matrixing & lan instruction m anual a-neuvideo.Com frisco, texas 75034 (469) 277-7606.

  • Page 2

    Safety information 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fi...

  • Page 3

    Table of contents a neu video 1 contents introduction & contents ..................................................2 features .................................................................................... 3 specifications ...........................................................................

  • Page 4

    2 introduction introduction this 10x10 hdmi/hdbaset ™ matrix supports routing and transmission of video (for resolutions up to 4k@60hz w/ hdmi 2.0 & hdcp 2.2) and audio (multi-channel digital/stereo analog) while providing flexible control via ir, rs-232, telnet or webgui. As many as (10) hd sources...

  • Page 5

    3 features & contents features base unit • hdmi 2.0, hdcp 1.4 and hdcp 2.2 compliant • routes (10) hdmi sources to (10) displays using (8) hdbaset ™ outputs and (2) independent or mirrored hdmi outputs • hdbaset ™ 5-play ™ convergence: high-definition video and audio, 100baset ™ ethernet, poh (power...

  • Page 6

    4 specifications specifications as product improvements are continuous, specifications are subject to change without notice. A neu video receiver • inputs: • cat5e/6/7 (rj45) • ir in • optical in • outputs: • hdmi • ir out 2 • others: • lan (rj45) • rs-232 (phoenix connector) • update slide switch •...

  • Page 7

    5 front panel front panel q power: press this button to power the unit on or place it into standby mode. Note: network functionality and poh (if the second power supply is connected) remains active when the unit is in stand-by mode. W power led: this led will illuminate green to indicate the unit is...

  • Page 8

    6 front panel receiver front panel q power led: this power led will illuminate when receiving power from the transmitter. W optical in: connects with an optical audio source as an optical audio return which sends audio back to the ani-1082uhd. E ir in 1: ir in 1 is considered an ir receiver which co...

  • Page 9

    7 rear panel rear panel q hdmi in & ir out 1~10: connects up to (10) source devices to the hdmi ports using appropriate quality hdmi cables. Input source devices include blu-ray players, set-top boxes, game systems and so on. These inputs are dvi-d compliant (with the use of dvi to hdmi adapters or ...

  • Page 10

    8 rear & side panel rear panel a cat audio i/o 1~2: sends/receives audio to/from connected compatible cat audio devices via a standard cat5e cable. This connection allows audio to be sent to/from the matrix over greater distances than would normally be possible via standard cables. 48khz audio can b...

  • Page 11

    9 remote control remote control q power: press to power the unit on or place it into stand-by mode. W lock: press to lock/unlock the front panel of the matrix unit. E mute: mutes zone audio outputs. Hdbaset ™ audio can only be muted when an independent, non-hdmi, audio source has been routed to the ...

  • Page 12

    10 oled menu oled menu 1st level 2nd level 3rd level edid edid mode all independent edid select all 1~6 (default edid settings) 7~12 (sink’s edid settings) 13~16 (user’s edid settings) network link status (idle) ip address subnet mask gateway address mac address dhcp mode on off hdmi mirroring outpu...

  • Page 13

    11 rs-232 protocols rs-232 protocols matrix remote controller pin assignment pin assignment 1 nc 1 nc 2 tx 2 rx 3 rx 3 tx 4 nc 4 nc 5 gnd 5 gnd 6 nc 6 nc 7 nc 7 nc 8 nc 8 nc 9 nc 9 nc rs-232 & telnet commands commandsyntax the rs-232/telnet command structure for this unit is both flexible and powerf...

  • Page 14

    12 rs-232 & telnet commands rs-232 & telnet commands multi-parameter command format use the following syntax to set or change multiple parameters for a single port. Note: each additional parameter uses the “,” character for separation and spaces are allowed. The number of parameters allowed in a sin...

  • Page 15

    13 rs-232 & telnet commands rs-232 & telnet commands hdmi mirroring command example if you have rack (head end) based avr’s for surround sound rooms we recommend using the hdmi outputs and the hdmi mirroring mode to easily have the audio and video sent to the avr follow the signal sent to that zone’...

  • Page 16

    14 rs-232 & telnet commands full command list command description help displays all available commands. (except hidden commands.) ? Displays all available commands. (except hidden commands.) help {command} detailed description of the specified command. ? {command} detailed description of the specifi...

  • Page 17

    15 rs-232 & telnet commands full command list command description extlineout m name={namestring} sets the verbose name of an extended line output. Maximum 32 characters. M = 1~4 note: can only rename one port at a time. Multi-port is not supported. Audiocat_out m audiosrc=xxx sets the audio source f...

  • Page 18

    16 rs-232 & telnet commands full command list command description mixerout m gain n=xxx sets the gain level of an audio mixer input channel. M = 1~3 n = a~b xxx = 0~100 (units: %) mixerout m mono sets the output of a mixer channel to “mono” mode. Left and right channel outputs will be the same. M = ...

  • Page 19

    17 rs-232 & telnet commands full command list command description zoneavpair hdmi_out m slot n audiosrc=xxx assigns an audio source to a zone a/v pair slot on a hdmi output. M = i~j n = 1~11 available xxx values: hdmi_in n [n=1~10] coaxin n [n=1~2] oar_in n [n=a~h] mixerout n [n=1~3] opticin n [n=1~...

  • Page 20

    18 telnet control telnet control before attempting to use telnet control, please ensure that both the unit and the pc/laptop are connected to the same active networks. To access telnet in windows 7, click on the “start” menu and type “cmd” in the search field, then press “enter”. Under windows xp go...

  • Page 21

    19 webgui control webgui control install the device discovery tool: please obtain the device discovery software from our website and save it in a directory where you can easily find it. Note: the unit’s default ip address is 192.168.1.50 connect the unit and your pc/laptop to the same active network...

  • Page 22

    20 webgui control webgui control login to the webgui: by default, both the username and password are “admin” for the webgui. The administrator password can be changed within the “user config” tab of the webgui if desired. The above function tabs will always display on left side of the webgui to aid ...

  • Page 23

    Webgui control video switch this page provides video routing settings including hdcp and test pattern configuration. Output and input routing to begin assigning a new video route, please click the button of the hdbaset ™ output you wish to send video to (e.G. “hdbt_out a”) and then click on the butt...

  • Page 24

    Webgui control video switch hdmi output setting the (2) hdmi outputs (port i & port j) allow support for the maximum hdmi timing up to 18gbps (4096x2160@60hz) and can be used for normal source routing (listed as “independent” within the webgui) and mirroring (listed as “mirror” within the webgui) fo...

  • Page 25

    Webgui control video switch internal test pattern this advanced matrix system comes with an internal test pattern generation feature which can be used to test connected sink device functionality or be used to self-test matrix unit itself. This is a useful tool for installation engineers to troublesh...

  • Page 26

    Webgui control video switch preset setting this matrix can store up to (8) video and audio routing presets. Presets can be utilized to store multiple different routing states in advance for rapid, hassle-free, recall. Store: once you have the matrix set the way you like, you can click the “store” ic...

  • Page 27

    Webgui control zone audio this advanced matrix offers a complete audio routing function. The zone audio ports offer analog audio breakaway capability. The audio source, treble, bass, volume and audio delay adjustments can be set on this page. Output and input routing click the buttons from left to r...

  • Page 28

    Webgui control zone audio audio output setting click the “edit” icon ( ) to change the following settings: rename: the zone audio outputs can be renamed here. Volume: adjustable from -100db to 0db. Bass: adjustable from -12db to +12db. Treble: adjustable from -12db to +12db. Delay: adjustable from 0...

  • Page 29

    Webgui control extended audio the extended audio ports offers additional analog audio breakaway capability. The audio source, treble, bass, volume and audio delay adjustments can be set on this page. Output and input routing click the buttons from left to right to choose each output’s source. Once t...

  • Page 30

    Webgui control cat audio connecting compatible cat5e/6 receivers allows the matrix to both send and receive audio over distances up to 984ft/300m. The audio source and mute settings of audio being sent from the matrix to a receiver can be set on this page. Output and input routing click the buttons ...

  • Page 31

    Webgui control hdmi audio the audio routed to the (2) hdmi outputs (ports: i & j) and their associated settings are adjusted on this page. Output and input routing click the buttons from left to right to choose each output’s source. Once the new source has been selected, the change will happen immed...

  • Page 32

    Webgui control hdbaset™ audio the audio routed to the (8) hdbaset ™ outputs (ports: a~h) and their associated settings are adjusted on this page. Output and input routing click the buttons from left to right to choose each output’s source. Once the new source has been selected, the change will happe...

  • Page 33

    Webgui control mixer audio the audio mixer feature allows for any (2) audio sources to be mixed together. The matrix has (3) mixers in total and their settings can be adjusted on this page. Output and input routing click the buttons from left to right to choose each mixer’s a & b sources. Only (2) s...

  • Page 34

    Webgui control zone a/v pairing the zone a/v pairing function allows the end user to control the matrix, using the supplied remote control, in a customized manner while in remote rooms (zones) containing a hdbaset ™ receiver and ir extender. Each zone can have a different set of video/audio sources ...

  • Page 35

    Webgui control edid settings this matrix provides the option of (6) standard edids, (10) sink sourced edids and (4) customer uploaded edids that can be assigned to each input port individually. The names of the (4) customers uploaded edids can be changed if desired. Customer edid settings to upload ...

  • Page 36

    Webgui control edid settings set edid input content the set edid input content section allows for the assignment of an edid to each individual input port, or to all inputs at once. Click the selection bar to toggle between individual assignment, or all inputs. The unit comes with the following (6) d...

  • Page 37

    Webgui control hdbaset™ & h/w info this page provides information concerning the temperature inside the matrix (areas 1, 2 & 3) and the hdbaset ™ firmware versions used in the matrix and in connected receivers. Temperature area 1 is the left side of the output ports (from the front), area 2 is the r...

  • Page 38

    Webgui control system settings this page provides system configuration options including turning the power on/off, changing the network settings, downloading/restoring saved system configurations, resetting the system to factory defaults and updating the firmware. Click the “download” button to save...

  • Page 39

    Connection diagram connection diagram: main unit a neu video 37.

  • Page 40

    Ir cable pin assignment ir cable pin assignment a neu video 38.

  • Page 41

    Video specifications supported hdmi resolutions: main unit input & output resolutions (hz) 480i@60hz 800x600@60hz 1280x1024@60hz 3840x2160@24/25/30/50/59.94/60hz (yuv_444) (6g) 480p@60hz 720p@50/60hz 1360x768@60hz 4096x2160@24/50/59.94/60hz (yuv_444) (6g) 576i@60hz 1080i@50/60hz 1600x1200@60hz 576p@...

  • Page 42

    Audio specifications analog audio analog inputs max audio level 2vrms input impedance >10kΩ analog outputs 0dbfs output level 2vrms thd ≤ 80% 1k 0dbfs thd ≤ 90% 1k -1dbfs snr >100db@1k 0dbfs frequency response crosstalk output impedance >470Ω linear pcm audio channels (khz) lpcm 2.0@44.1 lpcm 5.1@44...

  • Page 43

    Category cable specifications & hdbaset™ features category cable specifications: main unit cabletype cable length supported video format cat5e/6 328ft/100m most common full hd video: • up to 1080p@60hz, 36-bit color • data rates lower than 5.3gbps or below 225mhz tmds clock 230ft/70m full hd & ultra...

  • Page 44

    End of document 42 terms & conditions of use please read the following terms and conditions carefully before using this hardware, components and software provided by, through or under a-neuvideo, inc (collectively, the “product”). By using installing or using the product, you unconditionally signify...