1. DL manuals
  2. A-Neu Video
  3. Matrix Switcher
  4. ANI-MODZ16
  5. Instruction Manual

A-Neu Video ANI-MODZ16 Instruction Manual

Manual is about: ANI-MODZ Series: Modular Matrix Switcher

Summary of ANI-MODZ16

  • Page 1

    Audio / video manufacturer ani-modz ani-modz series: modular matrix switcher instruction m anual ™ ™ ® a-neuvideo.Com frisco, texas 75034 (469) 277-7606.

  • Page 2

    Safety information 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fi...

  • Page 3

    Table of contents a neu video 1 contents package contents ................................................................1 introduction ........................................................................... 2 system requirements ......................................................... 2 featu...

  • Page 4

    2 introduction & features introduction the ani-modz modular matrix is designed to allow the switching and distribution of up to (32) source devices to up to (32) connected displays (model specific), either directly via a hdmi, dvi or cat5e/6/7 outputs to compatible receivers, providing control optio...

  • Page 5

    3 specifications main units ani-modz8 general input modular slots (1) output modular slots (1) input channels (8) hdmi or dvi or cat5e/6/7 or vga (dependent on module configuration) output channels (8) hdmi or dvi or cat5e/6/7 (dependent on module configuration) power supply ac 110~240v 50/60hz (us/...

  • Page 6

    4 specifications main units ani-modz 16 general input modular slots (2) output modular slots (2) input channels (16) hdmi or dvi or cat5e/6/7 or vga (dependent on module configuration) output channels (16) hdmi or dvi or cat5e/6/7 (dependent on module configuration) power supply (2) ac 110~240v 50/6...

  • Page 7

    5 specifications main units ani-modz 32 general input modular slots (4) output modular slots (4) input channels (32) hdmi or dvi or cat5e/6/7 or vga (dependent on module configuration) output channels (32) hdmi or dvi or cat5e/6/7 (dependent on module configuration) power supply (2) ac 110~240v 50/6...

  • Page 8

    6 specifications ani-modz signal card (changeable cards) the ani-modz series input and output cards for installation into the modular matrix switcher chassis are classified into the following models. Ani-modz input cards ani-modz output cards models inputs signal format models outputs signal format ...

  • Page 9

    7 ani-modz8 front panel operation ani-modz8: the front panel of ani-modz8 is shown below. Q lcm: displays the setting information of each input/output and other setting information according to the selected mode. W ir window: accepts the ir remote control signal for the matrix only. E power: press t...

  • Page 10

    8 ani-modz8 back panel operation ani-modz8: the back panel of the ani-modz8 is shown below. Note:theabovepanelisanexampleof8x8hdmiconfiguration. Q outputs 1~8: install an output module as required for connection to up to (8) displays (tvs or monitors) or cat5e/6/7 outputs or compatible hdbaset ™ rec...

  • Page 11: I O A

    9 ani-modz 16/ani-modz32 front panel operation ani-modz16/ani-modz32: the front panel for both the ani-modz16 and the ani-modz32 is shown below. Q lcm: displays the setting information of each input/output and other setting information according to the selected mode. W ir window: accepts the ir remo...

  • Page 12

    10 ani-modz 16 back panel operation ani-modz16: the back panel for the ani-modz16 is shown below. Note:theabovepanelisanexampleof16x16hdmiconfiguration. Q output 1~16: install up to (2) output modules as required for up to (16) displays (tvs or monitors) or cat5e/6/7 outputs for compatible hdbaset ™...

  • Page 13

    11 ani-modz32 back panel operation ani-modz32: the back panel for the ani-modz32 is shown below. Note:theabovepanelisanexampleofthe32x32hdmiconfiguration. Q output 1~32: installs up to (4) output modules as required for up to (32) displays (tvs or monitors) or cat5e/6/7 outputs for compatible hdbase...

  • Page 14

    12 remote control remote control q power: on/off button w output: output port button e input: input port button r enter: press to confirm the present input/output selection t clear: press to clear the present input/output selection channels should be entered using two digits. Forexample: entering ch...

  • Page 15

    13 input & output modules input modules ani-in-5p 8 port hdbaset ™ input module specifications video bandwidth 300mhz/10.2gbps features hd video/audio, poc, ethernet, ir/rs-232 pass thru input ports (8) cat5e/6/7, (1) lan ethernet speed 100mbps video resolutions pc: vga~wuxga hdtv: 480i~1080p@60hz &...

  • Page 16

    14 input & output modules input modules ani-in-dv 8 port dvi input module specifications video bandwidth 225mhz/6.75gbps input ports (8) dvi video resolutions pc: vga~wuxga@60 (rb) hdtv: 480i~1080p@60hz audio transmission lpcm7.1ch, dolby truehd, dolby digital plus, dts-hd master audio (32~192khz fs...

  • Page 17

    15 input & output modules output modules ani-out-5p 8 port hdbaset ™ output module specifications video bandwidth 300mhz/10.2gbps features hd video/audio, poc, ethernet, ir, rs-232 pass thru output ports (8) cat5e/6/7, (1) lan, (8) ir extender, (8) ir blaster ethernet speed 100mbps video resolutions...

  • Page 18

    16 input & output modules output modules ani-out-4k 8 port 4k hdmi output module specifications video bandwidth 300mhz/10.2gbps output ports (8) hdmi video resolutions pc: vga~wuxga hdtv: 480i~1080p@60hz, 4k2k@30hz audio transmission lpcm7.1ch, dolby truehd, dolby digital plus, dts-hd master audio (...

  • Page 19

    17 transmitter & receiver options transmitters & receivers manufacture part# type body type 4k 3d hd audio ir rs-232 ethernet poc* external power 1080p@60hz/ uhd cable length ani-315xlr receiver stand alone ü ü ü 1-way ü ------ ----- 5v 60 / 35m ani-315xlt transmitter stand alone ü ü ü 1-way ü -----...

  • Page 20

    18 connection diagram example installation (32x32 hdmi matrix) a neu video.

  • Page 21

    19 ir cable pin assignments a neu video q w e power ir signal nc q w e ir signal power grounding.

  • Page 22

    20 rs-232 protocols matrix ► ◄ rs-232 control pin definition pin definition 1 nc 1 nc 2 txd 2 rxd 3 rxd 3 txd 4 nc 4 nc 5 gnd 5 gnd 6 nc 6 nc 7 nc 7 nc 8 nc 8 nc 9 nc 9 nc baud rate: 19200bps data bit: 8bits parity: none stop bit: 1 flow control: none a neu video.

  • Page 23

    21 rs-232 & telnet commands command codes functions p1 power on p0 power off oxiy set output (x=1~32) to input (y=1~32) allout x set all outputs to input (x=1~32) active report active i/o channels indetect input channel detection indicator outdetect output channel detection indicator portstatus repo...

  • Page 24

    22 rs-232 & telnet commands command codes functions irmaskcpu x y z* disable/enable (z=0/1) ir transmission from the ir all input on the cpu control board to the hdbaset ™ transmitter (x=src), receiver (x=sink) or output module (x=out) on to the specified port (y=1~32/all). Example1: “irmaskcpu src ...

  • Page 25

    23 telnet control setup procedure for 4k2k uhd the default edid setting, regardless of i/o cards, is 1080p@60hz. Because edid determines when a source can output a 4k2k signal, the matrix switcher must be told which source and display to use for edid information exchange. These changes are done usin...

  • Page 26

    24 telnet control before attempting to use the telnet control, please ensure that both the matrix (via the ‘lan /control’ port) and the pc/laptop are connected to the same active networks. To access the telnet control in windows 7, click on the “start” menu and type “cmd” in the “search” field, then...

  • Page 27

    25 telnet control this will bring us into the unit which we wish to control. Type “help” to list the available commands. Type “ipconfig” to show all the ip configurations. To reset the ip, type “rstip” and to use a static ip, type “setip” (for a full list of commands, see section rs-232 & telnet com...

  • Page 28

    26 web gui control on a pc/laptop that is connected to the same active network as the matrix, open a web browser and type the unit’s “ip address” on the web address entry bar. The browser will display the unit’s status, control and user setting pages. Click on the “control” tab to control power, inp...

  • Page 29

    This page is intentionally left blank..

  • Page 30

    This page is intentionally left blank..

  • Page 31

    This page is intentionally left blank..

  • Page 32

    30 end of document terms & conditions of use please read the following terms and conditions carefully before using this hardware, components and software provided by, through or under a-neuvideo, inc (collectively, the “product”). By using installing or using the product, you unconditionally signify...