- DL manuals
- A-Neu Video
- Matrix Switcher
- HD-44
- Instruction Manual
A-Neu Video HD-44 Instruction Manual
Summary of HD-44
Page 2
Safety information 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fi...
Page 3
Table of contents contents introduction & package contents ....................1 features & specifications ......................................2 edid functions ..........................................................3 front panel .................................................................4...
Page 4
Features & specifications features • support 4 x hdmi digital source devices matrix switched to 4 x hdmi devices. • hdmi digital video w/ embedded audio, dvi format and hdcp compliant • seven (7) function key control and worldwide edid modes for hdtv resolutions. • link speeds of up to 2.25 gbps (li...
Page 5
Edid function edid function for hdmi matrix switcher to view the current edid status: step 1. Press edid button; the button will flash blue and the display will show the current edid status. Step 2. Press edid button to exit. To change the current edid status: method 1 step 1. Press edid button; the...
Page 6
4 front panel front panel 1 power switch the power switch turns the unit on and off. The led will illuminate red to indicate that the switcher is on and is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last confi guration wi...
Page 7
5 front panel front panel 9 function key - off disables (mute) video to selected channels. Either destinations. - press off button followed by any destination channel. - press 1 thru 4 output destination. The display will show ” 0 “ for the selected channel indicating no video selected. 10 function ...
Page 8
6 rear panel rear panel 1 dc power inlet the switcher is fi tted with a dc power plug input connector. Ensure that the used is of an approved type and is of suffi cient current carrying connector capacity with the correct voltage and connector polarity. 12volt~ dc power supply 3a max (center pin pos...
Page 9
Typical application installing diagram 4x4 hdmi matrix switcher hd-44 connection ports: control ports : 1. Ir extend - extemal ir receiver 2. Rs-232 - pc rs-232 series port inputs port signals: 1. Hdmi (hdcp compliant) 2. Hdmi (hdcp compliant) 3. Hdmi (hdcp compliant) 4. Hdmi (hdcp compliant) output...
Page 10
Remote control before making any connections to the switcher. Observe the following: > ensure the mains voltage supply matches the label on the supplied plug-pack (+/- 10%) > ensure that the power switch is off > ensure that all system grounds (earth) are connected to a common point. > avoid powerin...
Page 11
Ir extender rear panel ir extender port *** when you plug the external ir extender into the switcher, the front panel ir receiver remains active. *** ir extender package 9.
Page 12
Rs-232 serial interface rs-232 serial interface connect a pc or control system. Version compatible v1.0 & v1.5 rs-232 serial interface pin rs-232 defi nition 1 -------- not used 2 tx transmitter 3 rx receiver 4 -------- not used 5 gnd ground 6 -------- not used 7 -------- not used 8 -------- not use...
Page 13
Rs-232 serial commands more stuff note: turning the unit system power 011 via rs-232 will extinguish the led channel display leaving only the power sw~ led on. The video and audio outputs will also mute. While the unit is turned 011 by rs-232 it will continue to accept and act upon switching command...
Page 14
Gui interface 1a: supports routing using lines 12.
Page 15
Gui interface 1b: supports routing using cross points 13.
Page 16
Gui interface 2: select different matrix sizes 14.
Page 17
Gui interface 3: support com ports 1 thru 4 15.
Page 18
16 end of document terms and conditions of use please read the following terms and conditions carefully before using this hardware, components and software provided by, through or under a-neuvideo, inc (collectively, the “product”). By using installing or using the product, you unconditionally signi...