1. DL manuals
  2. A-Neuvideo
  3. Matrix Switcher
  4. HD-44AK
  5. Instruction Manual

A-Neuvideo HD-44AK Instruction Manual

Manual is about: 8x8 HDMI Matrix Switch with Auxiliary Audio I/O

Summary of HD-44AK

  • Page 1

    Audio / video manufacturer hd-88ak 8x8 hdmi matrix switch with auxiliary audio i/o v2.0 instruction m anual a-neuvideo.Com frisco, texas 75034 (317) 456-2461.

  • Page 2

    Safety information 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fi...

  • Page 3

    Table of contents a neu video 1 contents introduction & package contents ...............................1 features ....................................................................................2 specifications .........................................................................3 front pan...

  • Page 4

    2 features features • (8) hdmi with auxiliary audio (analog audio) source devices matrix switched to (8) hdmi with s/pdif output destinations • hdmi digital video w/embedded hdcp, dvi format and cec/hdcp 2.0 compliant • worldwide control edid modes for hdmi full 4k2k (24/30 hz) hd video resolutions ...

  • Page 5

    3 specifications specifications • type of switcher: 8x inputs to 8x outputs hdmi matrix switcher with audio and extension • hdmi support: hdmi 4k2k, 1080p@60hz, h36-bit deep color, 3d of hdmi v1.4 formats • hdcp / cec support: hdcp 2.0 compliant, cec compliant • video bandwidth: double data rates: 3...

  • Page 6

    4 front panel front panel q power switch: the power switch turns the unit on and off. The led will illuminate red to indicate that the switcher is on and is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration wi...

  • Page 7

    5 front panel front panel o function key - arc: audio return channel (arc) is a feature that sends audio from the tv back down the hdmi cable to its source device, in this case, the switcher, not all displays support arc; check your users guide for additional information. ( default = arc disabled ) ...

  • Page 8

    6 front panel front panel a function key - aux (the audio additional on the “ audio / arc” port) the aux function feature allows you to replace the embedded hdmi audio signal with an audio signal that is connected to the switchers audio aux input. Using the aux function replaces the audio and does n...

  • Page 9

    7 front panel front panel d function key - edid used to display change current edid mode. - press edid to select new edid mode or select - press source row #1 or #2 select edid modes. - press enter to ready memory location. - or press edid again to cancel operation. Operation completes. Note : opera...

  • Page 10

    8 front panel front panel f function key - all disables (mute) video on all destinations or selects the same source to all destinations. Option 1 - press all followed by off button. The display will show “ 0 “ indicating all destinations have no video selected. Option 2 - press all followed by sourc...

  • Page 11

    9 front panel front panel k function key - recall the system will show previously stored presets, up to a total of 16. Presets are stored in local memory using source keys 1 thru 8 or destination keys 1 thru 8 as the memory preset location. - press recall button. - press 1 thru 8 on either source or...

  • Page 12

    10 rear panel rear panel a neu video q dc power inlet: the switcher is fitted with a dc power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12volt dc power supply 5a max (cen...

  • Page 13

    11 rear panel rear panel a neu video t inputs- 1,2,3,4,5,6,7, & 8 hdmi: connect an hdmi signal source to this input. This hdmi port supports hdmi with embedded audio and dvi with aux audio sources. If you remove the hdmi screw post, you must use the provided iso screws to keep the internal hdmi jack...

  • Page 14

    12 typical application installing diagram samples connection : 1. Using ir external, rs-232 or ethernet command to control switcher hd-88ak via pc or ir rx-100 ir receiver transmit the hd-88ak’s ir signal. 2. Audio output link arc from tv return channel, hdmi audio source or mixing auxiliary audio. ...

  • Page 15: Q W

    13 remote control before making any connections to the switcher. Observe the following: • ensure the mains voltage supply matches the label on the supplied plug-pack (+/- 10%) • ensure that the power switch is off • ensure that all system grounds (earth) are connected to a common point. • avoid powe...

  • Page 16

    14 remote control ir remote custom and data codes (nec standard) how to setup ir codes : model number : hd-88ak custom code : 03fc power on : 03fc a15e power off : 03fc a25d arc : 03fc b847 aux : 03fc 9966 all : 03fc b04f off : 03fc b14e edid : 03fc b748 lock : 03fc b54a recall : 03fc b24d memory : ...

  • Page 17

    15 ir extender a neu video note: the external ir jack has voltage on the “ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug). Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off. *** when you plug the exte...

  • Page 18

    16 ir extender a neu video pin configuration: ani-101 and ani-101c transmitter pin configuration 1. Ani-101 ir 300m transmitter device cable (3c) ir transmitter (ani-101) ani-101 maximum distance ~ 984 feet (300m) ani-101c maximum distance ~ 6 feet (2m) ani-101 ir transmitter set r ohs /95/e c dc 12...

  • Page 19

    17 edid function edid function setup edid setup to change the edid setup step 1. Press the edid button the display will show the currently selected edid mode step 2. Press source #1 or #2 button row the button will flash blue and the display will show the current embedded edid status. Step 3. Press ...

  • Page 20

    18 edid function edid function : 7x embedded edid modes mode 1. Fss ® (fast speed start) fast speed start mode shortens the startup time of the switcher. Selecting this mode does not force the edid setup to be cancelled. Users may first select one edid mode from mode 2 to 3, and then select mode 1 f...

  • Page 21

    19 edid function edid function : learning learning edid single to single example : learn destination #8 edid to source #5. Step 1. Press the edid button the button will flash blue and the display will show the current embedded edid status. Step 2. Press the destination #8 button row copy the destina...

  • Page 22

    20 edid function edid function for hdmi matrix switcher learning edid learning edid from destination to source learning edid setup press edid > destination > source > enter press edid > destination button: the lcm will be show learning switcher will learn destination hdmi edid and pass the selected ...

  • Page 23

    21 ethernet & rs-232 serial interface ethernet serial interface connect a pc or control system. Version compatible v2.0 for a complete list of commands, please reference external document extended ethernet protocol instruction manual. Ethernet serial interface pin ethernet reference 1 txop tx + 2 tx...

  • Page 24

    End of document 22 terms and conditions of use please read the following terms and conditions carefully before using this hardware, components and software provided by, through or under a-neuvideo, inc (collectively, the “product”). By using installing or using the product, you unconditionally signi...