1. DL manuals
  2. Aaeon
  3. Desktop
  4. AEC-6523
  5. User Manual

Aaeon AEC-6523 User Manual

Manual is about: Embedded Controller Intel Atom N2600 Dual Core 1.6GHz Processor Dual LAN, 4 USB2.0, 4 COM, 1 VGA 1 Mini Card

Summary of AEC-6523

  • Page 1

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 aec-6523 embedded controller intel ® atom™ n2600 dual core 1.6ghz processor dual lan, 4 usb2.0, 4 com, 1 vga 1 mini card aec-6523 manual 1 st ed. December 2013.

  • Page 2

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 i copyright notice this document is copyrighted, 2013. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be rep...

  • Page 3

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 ii acknowledgments all other products’ name or trademarks are properties of their respective owners. • ami is a trademark of american megatrends, inc. • compactflash ™ is a trademark of the compact flash association. • microsoft windows ® is a regi...

  • Page 4

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 iii packing list before you begin operating your pc, please make sure that the following materials are enclosed: z 1 aec-6523 embedded controller z 2 wallmount brackets z 1 screw package z 1 dvd-rom for manual (in pdf format) and drivers z 1 phoeni...

  • Page 5

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 iv safety & warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any ac outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth....

  • Page 6

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 v d. The equipment does not work well, or you cannot get it to work according to the user’s manual. E. The equipment has been dropped and damaged. F. The equipment has obvious signs of breakage. 15. Do not leave this equipment in an environment whe...

  • Page 7

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 vi below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon boxer/ industrial system 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 中央处理器 与内存 × ○ ○ ○ ○...

  • Page 8

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 vii chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications ...........................

  • Page 9: Appendix C  Ahci Setting

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 viii chapter 4 driver installation 4.1 installation ................................................................. 4-3 appendix a programming the watchdog timer a.1 programming ........................................................A-2 a.2 ite8...

  • Page 10: General

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 1 general information 1- 1 chapter general 1 information.

  • Page 11

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 1 general information 1- 2 1.1 introduction aaeon introduces the newest product in the boxer series, aec-6523, which utilizes the intel ® atom™ n2600 processor: this embedded controller expands its graphics performance greatly with the newe...

  • Page 12

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 1 general information 1- 3 1.2 features z intel ® atom tm n2600 dual core 1.6ghz processor z intel ® nm10 express chipset z intel ® gma 3600 integrated graphic engine z usb2.0 x 4 z com x 4 z dual gigabit ethernet lan z vga output z fanless...

  • Page 13

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 1 general information 1- 4 1.3 specifications system z cpu intel ® atomtm n2600 dual core 1.6ghz processor z memory ddr3 sodimm x 1, supports ddr3 800/1066, max. 2gb z vga vga x 1 z ethernet gigabit ethernet, rj-45 connector x 2 z hard disk...

  • Page 14

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 1 general information 1- 5 mechanical and environmental z construction rugged aluminum alloy chassis z color dark gray z mounting wall mount/vesa/din rail z dimension 8.35”(w) x 3.1”(h) x 2.25”(d) (212.15 mm x 78.88 mm x 107 mm) z gross wei...

  • Page 15

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 1 general information 1- 6 z emc ce/fcc class a.

  • Page 16: Hardware

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2-1 ch hardware installation apter 2.

  • Page 17

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 2 2.1 dimension and i/o of aec-6523 cfast.

  • Page 18

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 3 2.2 connectors and jumpers of the main board component side.

  • Page 19

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 solder side chapter 2 hardware installation 2 - 4.

  • Page 20

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 5 2.3 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function jp1 auto...

  • Page 21

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 6 2.4 list of connectors the board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: label function cn1 fr...

  • Page 22

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 7 cn25 stereo-l channel cn26 1st lvds inverter cn27 1st lvds (single channel 18/24bit) cn28 2nd rj-45 ethernet cn29 1st rj-45 ethernet cn30 usb port #1 and #2 cn31 audio line in/out and mic cn32 crt/dvi (configur...

  • Page 23

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 8 2.5 auto power button selection (jp1) jp1 function 1-2 enable 2-3 disable (default) 2.6 clear cmos (jp2) jp2 function 1-2 normal (default) 2-3 clear cmos 2.7 com2 ri/+5v/+12v selection (jp3) jp3 function 1-2 +1...

  • Page 24

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 9 rs-232 mode pin signal pin signal 1 dcdb 2 rxb 3 txb 4 dtrb 5 ground 6 dsrb 7 rtsb 8 ctsb 9 rib/+5v/(+12v) rs-422 mode pin signal pin signal 1 txd- 2 rxd+ 3 txd+ 4 rxd- 5 ground 6 n/c 7 n/c 8 n/c 9 n/c / +5v / ...

  • Page 25

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 10 9 ric 2.11 com port 4 connector pin signal pin signal 1 dcdd 2 rxd 3 txd 4 dtrd 5 ground 6 dsrd 7 rtsd 8 ctsd 9 rid.

  • Page 26

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 11 2.12 hard disk drive installation step 1: open the bottom case of aec-6523 by loosening the two screws. Step 2: get the hard disk drive ready..

  • Page 27

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 12 step 3: install the cfast™ card. Step 4: fasten the cover of the cfast™ card..

  • Page 28

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 13 step 5: stack the hdd and bracket. Fasten the hdd and bracket with the screws. Step 6: connect the sata and power cables to the hdd..

  • Page 29

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 14 step 7: fasten the bracket of the hdd. Step 8: fasten the bottom hdd kit case of aec-6523..

  • Page 30

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 15 2.13 sd ram installation step 1: loosen the bottom hdd kit of the aec-6523. Step 2: fasten the bottom case of the aec-6523..

  • Page 31

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 16 step 3: loosen the screw on the front panel of aec-6523 step 4: loosen the screws on the rear panel of aec-6523.

  • Page 32

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 17 step 5: insert the sdram to the memory slot. Step 6: press the sdram and make sure that it has been inserted properly..

  • Page 33

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 18 step 7: adhere the heat-spreading sheet to the sdram. Step 8: close the bottom case of aec-6523 and fasten the four screws on the bottom case..

  • Page 34

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 19 step 8-1: close the bottom hdd kit case of aec-6523 and fasten the two screws on the bottom case. Step 9: close the front case of aec-6523 and fasten the screw on the front case..

  • Page 35

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 20 step 10: close the rear case of aec-6523 and fasten the two screws on the rear case..

  • Page 36

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 21 2.14 din rail installation step 1: fix the din rail kit with the screws on the chassis as shown below. Step 2: press the din rail on the din rail kit to fix it..

  • Page 37

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 2 hardware installation 2 - 22 2.15 wallmount installation step 1: fasten the brackets with the screws. We suggest using this screw..

  • Page 38: Ami

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 3 award bios setup 3-1 chapter ami 3 bios setup.

  • Page 39

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal ...

  • Page 40

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 chapter 3 award bios setup 3-3 3.2 ami bios setup ami bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information...

  • Page 41

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 setup submenu: main options summary: ( default setting ) system date day mm:dd:yyyy change the month, year and century. The ‘day’ is changed automatically. System time hh : mm : ss change the clock of the system. Chapter 3 ami bios setup 3-4.

  • Page 42

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 setup submenu: advanced options summary: ( default setting ) acpi settings system acpi parameters s5 rtc wake settings enable system to wake from s5 using rtc alarm. Cpu configuration cpu configuration parameters sata configuration sata device options se...

  • Page 43

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 usb configuration parameters super io configuration system super io chip parameters h/w monitor monitor hardware status chapter 3 ami bios setup 3-6.

  • Page 44

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 acpi settings options summary: ( default setting ) suspend disabled s1 only(cpu stop clock) acpi sleep state s3 only(suspend to ram) select the acpi state used for system suspend chapter 3 award bios setup 3-7.

  • Page 45

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 rtc wake settings options summary: ( default setting ) disabled wake system with fixed time enabled enable or disable system wake on alarm event. Wake up time is setting by following settings. Wake up hour 0-23 wake up minute 0-59 wake up second 0-59 cha...

  • Page 46

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 disabled wake system with dynamic time enabled enable or disable system wake on alarm event. Wake up time is current time + increase minutes. Wake up minute increase 1-5 chapter 3 award bios setup 3-9.

  • Page 47

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 cpu configuration options summary: ( default setting ) disabled hyper-threading enabled en/disable cpu hyper-threading function chapter 3 ami bios setup 3-10

  • Page 48

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 sata configuration ( ide ) options summary: ( default setting ) disabled sata controller(s) enabled en/disable sata controller ide configure sata as ahci configure sata controller operating as ide/ahci mode. Chapter 3 award bios setup 3-11.

  • Page 49

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 sata configuration ( ahci ) options summary: ( default setting ) disabled sata controller(s) enabled en/disable sata controller ide configure sata as ahci configure sata controller operating as ide/ahci mode. Disabled sata port 0/port 1 enabled chapter 3...

  • Page 50

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 en/disable the selected port. Disabled sata port 0/port 1 hot plug enabled en/disable hot plug feature for specified port. Chapter 3 award bios setup 3-13.

  • Page 51

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 usb configuration options summary: ( default setting ) enabled disabled legacy usb support auto enables bios support for legacy usb support. When enabled, usb can be functional in legacy environment like dos. Auto option disables legacy support if no usb...

  • Page 52

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 forced fdd hard disk cd-rom if auto. Usb devices less than 530mb will be emulated as floppy and remaining as floppy and remaining as hard drive. Forced fdd option can be used to force a hdd formatted drive to boot as fdd(ex. Zip drive) chapter 3 award bi...

  • Page 53

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 super io configuration options summary: ( default setting ) serial port 1/2/3/4 configuration set parameters of serial port 1/2/3/4 power off power on restore ac power loss last state select ac power state when power is re-applied after a power failure. ...

  • Page 54

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 serial port 1 configuration options summary: ( default setting ) disabled serial port enabled en/disable specified serial port. Auto io=3f8h; irq=4; io=3f8h; irq=3,4,5,7,10,11,12; io=2f8h; irq=3,4,5,7,10,11,12; io=3e8h; irq=3,4,5,7,10,11,12; change setti...

  • Page 55

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 serial port 2 configuration options summary: ( default setting ) disabled serial port enabled en/disable specified serial port. Auto io=2f8h; irq=3; io=3f8h; irq=3,4,5,7,10,11,12; io=2f8h; irq=3,4,5,7,10,11,12; io=3e8h; irq=3,4,5,7,10,11,12; change setti...

  • Page 56

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 select a resource setting for super io device. Rs232 rs422 com2 type select rs485 configure com2 operated as rs232, rs422 or rs485. Chapter 3 award bios setup 3-19.

  • Page 57

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 serial port 3 configuration options summary: ( default setting ) disabled serial port enabled en/disable specified serial port. Auto io=3e8h; irq=10; io=3f8h; irq=3,4,5,6,7,9,10,11,12; io=2f8h; irq=3,4,5,6,7,9,10,11,12; io=3e8h; irq=3,4,5,6,7,9,10,11,12;...

  • Page 58

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 serial port 4 configuration options summary: ( default setting ) disabled serial port enabled en/disable specified serial port. Auto io=2e8h; irq=11; io=3f8h; irq=3,4,5,6,7,9,10,11,12; io=2f8h; irq=3,4,5,6,7,9,10,11,12; io=3e8h; irq=3,4,5,6,7,9,10,11,12;...

  • Page 59

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 h/w monitor chapter 3 ami bios setup 3-22.

  • Page 60

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 setup submenu: chipset options summary: ( default setting ) host bridge host bridge parameters south bridge south bridge parameters chapter 3 award bios setup 3-23.

  • Page 61

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 host bridge options summary: ( default setting ) intel igd configuration configure intel igd settings. Chapter 3 ami bios setup 3-24.

  • Page 62

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 intel igd configuration options summary: ( default setting ) enabled auto disable igd disabled select primary boot display device igfx – boot type crt select primary boot display device 128mb fixed graphics memory size 256mb configure fixed graphics memo...

  • Page 63

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 south bridge options summary: ( default setting ) atx type power mode at type select the power type used on the system tpt devices hd audio and onboard lan settings. Pcie mini-card slot pcie mini-card slot settings. Chapter 3 ami bios setup 3-26.

  • Page 64

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 tpt devices options summary: ( default setting ) disabled azalia controller hd audio enable or disabled azalia controller disabled r8111e #1 controller enabled enable or disable pcie lan. Disabled r8111e #2 controller enabled enable or disable pcie lan. ...

  • Page 65

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 setup submenu: boot options summary: ( default setting ) disabled quiet boot enabled en/disable showing boot logo. Disabled launch rtl8111e pxe oprom enabled en/disable pxe boot for rtl8111e lan boot option #x/ xxxx drive bbs priorities the order of boot...

  • Page 66

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 bbs priorities options summary: ( default setting ) disabled boot option #x device name sets the system boot order chapter 3 award bios setup 3-29.

  • Page 67

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 setup submenu: security options summary: ( default setting ) not set administrator password/ user password chapter 3 ami bios setup 3-30

  • Page 68

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 you can install a supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the features in the setup utility. Install the password: press enter on this item, a...

  • Page 69

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 hdd security options summary: ( default setting ) not set set user password/ set master password chapter 3 ami bios setup 3-32.

  • Page 70

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 you can install a master and user password. Before booting to os, hdd will be set to frozen state. On s3 resume hdd will be unlocked using the hdd password we entered while system booting. Install the password: press enter on this item, a dialog box appe...

  • Page 71

    S u b c o m p a c t b o a r d a e c - 6 5 2 3 setup submenu: exit options summary: ( default setting ) save changes and reset reset the system after saving the changes discard changes and reset reset system setup without saving any changes restore defaults restore/load default values for all the set...

  • Page 72: Driver

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 4 driver installation 4 - 1 chapter driver 4 installation.

  • Page 73

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 4 driver installation 4 - 2 the aec-6523 comes with a dvd-rom that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: step 1 – install chipset driver step 2 – install vga driver step 3...

  • Page 74

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 4 driver installation 4 - 3 4.1 installation: insert the aec-6523 dvd-rom into the dvd-rom drive, and then install the drivers from step 1 to step 6 in order. Step 1 – install chipset driver 1. Click on the step1-chipset folder and select t...

  • Page 75

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 4 driver installation 4 - 4 step 3 – install lan driver 1. Click on the step3-lan folder and select the os folder your system is 2. Double click on the setup.Exe located in each os folder 3. Follow the instructions that the window shows 4. ...

  • Page 76

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 chapter 4 driver installation 4 - 5 located in each os folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically note: if the os is chinese version, you may click on serial patch v1.0.1. Ex...

  • Page 77: Programming The

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-1 programming the appendix a watchdog timer.

  • Page 78

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-2 a.1 programming aec-6523 utilizes the ite 8783 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the aaeon initial watchdog timer program is also attac...

  • Page 79

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-3 exit the mb pnp mode. Undesired result may occur if the mb pnp mode is not exited normally. (1) enter the mb pnp mode to enter the mb pnp mode, four special i/o write operations are to be performed duri...

  • Page 80

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-4 configure control (index=02h) this register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not require the software to clear them....

  • Page 81

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-5 82h, 92h default=001s0000b) watch dog timer 1,2,3 time-out value (lsb) register (index=73h,83h,93h, default=38h) watch dog timer 1,2,3 time-out value (msb) register (index=74h,84h,94h default=00h).

  • Page 82

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-6 a.2 ite8783 watchdog timer initial program .Model small .Code main: call enter_configuration_mode call check_chip mov cl, 7 call set_logic_device ;time setting mov cl, 10 ; 10 sec dec al watch_dog_setti...

  • Page 83

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-7 call superio_set_reg ; game port enable mov cl, 9 call set_logic_device initial_ok: call exit_configuration_mode mov ah,4ch int 21h enter_configuration_mode proc near mov si,word ptr cs:[offset cfg_port...

  • Page 84

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-8 call write_configuration_data ret exit_configuration_mode endp check_chip proc near mov al,20h call read_configuration_data cmp al,87h jne not_initial mov al,21h call read_configuration_data cmp al,81h ...

  • Page 85

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-9 out dx,al mov dx,word ptr cs:[cfg_port+06h] in al,dx ret read_configuration_data endp write_configuration_data proc near mov dx,word ptr cs:[cfg_port+04h] out dx,al xchg al,ah mov dx,word ptr cs:[cfg_po...

  • Page 86

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix a programming the watchdog timer a-10 set_logic_device proc near push ax push cx xchg al,cl mov cl,07h call superio_set_reg pop cx pop ax ret set_logic_device endp ;select 02eh->index port, 02fh->data port cfg_port db 087h,001h,055h,055h d...

  • Page 87: I/o Information

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix b i/o information b - 1 i/o information appendix b.

  • Page 88

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix b i/o information b - 2 b.1 i/o address map.

  • Page 89

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix b i/o information b - 3.

  • Page 90

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix b i/o information b - 4 b.2 1 st mb memory address map.

  • Page 91

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix b i/o information b - 5 b.3 irq mapping chart.

  • Page 92

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix b i/o information b - 6 b.4 dma channel assignments.

  • Page 93: Ahci Setting

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix c ahci setting c - 1 ahci setting a ppendix c.

  • Page 94

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix c ahci setting c-2 c.1 setting ahci os installation to setup ahci mode. Step 1: copy the files below from “driver cd -> step5-ahci\winxp_32\f6 install floppy for windows” to floppy disk. Step 2: setup os.

  • Page 95

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix c ahci setting c-3 step 3: press “ f6 ” step 4: choose “ s ”.

  • Page 96

    E m b e d d e d c o n t r o l l e r a e c - 6 5 2 3 appendix c ahci setting c-4 step 5: choose “ intel® nm10 express chipset ” step 6: it will show the model number you select and then press “ enter step 7: setup is loading files.