1. DL manuals
  2. Aaeon
  3. Controller
  4. BOXER-6614
  5. Manual

Aaeon BOXER-6614 Manual

Manual is about: Embedded Controller, Intel Quad Core N2930, 1.83GHz Processor, Dual LAN, 3 USB 2.0, 1 USB 3.0, 4 COM 1 Full Size, 1 Half Size Mini Card

Summary of BOXER-6614

  • Page 1

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 boxer-6614 embedded controller intel ® quad core n2930 1.83ghz processor dual lan, 3 usb2.0, 1 usb3.0, 4 com 1 full size, 1 half size mini card boxer-6614 manual 1 st ed. December 24, 2014.

  • Page 2

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 copyright notice this document is copyrighted, 2014. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be r...

  • Page 3

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 acknowledgments all other products’ name or trademarks are properties of their respective owners. • ami is a trademark of american megatrends, inc. • compactflash ™ is a trademark of the compact flash association. • microsoft windows ® is a reg...

  • Page 4

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 packing list before you begin operating your pc, please make sure that the following materials are enclosed: 1 boxer-6614 embedded controller 2 wallmount brackets 1 screw package 1 cd-rom for manual (in pdf format) and drivers 1 phoenix power c...

  • Page 5

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 safety & warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any ac outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth...

  • Page 6

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 d. The equipment does not work well, or you cannot get it to work according to the user’s manual. E. The equipment has been dropped and damaged. F. The equipment has obvious signs of breakage. 15. Do not leave this equipment in an environment w...

  • Page 7

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon boxer/ industrial system 部件名称 有毒有害物质或元素 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ○ ○ ○ 外壳 × ○ ○ ○ ○ ○ 中央处理器 与内存 × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○...

  • Page 8

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 1 general information 1.1 introduction ................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications ..........................

  • Page 9

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 2.20 lpt port (cn13) ...................................................... 2-23 2.21 com port 3 connector (cn14 of mainboard) ......... 2-24 2.22 com port 4 connector (cn15 of mainboard) ......... 2-26 2.23 digital io port (cn16) ................

  • Page 10

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 3 ami bios setup 3.1 system test and initialization. .................................. 3-2 3.2 ami bios setup ........................................................ 3-3 chapter 4 driver installation 4.1 installation ....................

  • Page 11: General

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 general information chapter 1 chapter 1 general information 1- 1.

  • Page 12

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 1.1 introduction aaeon introduces the newest product in the boxer series, boxer-6614, which utilizes the intel ® quad core 1.83ghz soc n2930: this embedded controller expands its graphics performance greatly with the newest generation of celero...

  • Page 13

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 1.2 features intel ® quad core 1.83ghz soc n2930 intel ® hd integrated graphics engine usb3.0 x 1, usb2.0 x 3 com x 4 dual gigabit ethernet lan vga+hdmi output, dual view/simultaneous display support sata 3.0gb/s full size mini card with sim sl...

  • Page 14

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 1.3 specifications system cpu intel ® quad core 1.83ghz soc n2930 memory ddr3l 1333 sodimm x 1, max. 8gb display vga x 1, hdmi x 1 ethernet gigabit ethernet, rj-45 connector x 2 minicard wireless module (optional) storage sata 3.0gb/s 2.5” hdd/...

  • Page 15

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 mechanical and environmental construction metal fe. Color dark gray mounting desktop mount/ wallmount/ din rail dimension 8.71”(w) x 3.32”(h) x 2.25”(d) (221.15mm x 84.28mm x 107mm) gross weight 6.16 lb (2.8kg) net weight 4.4 lb (2.0kg) operati...

  • Page 16: Hardware

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2-1 hardware installation chapter 2.

  • Page 17

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 2 2.1 dimension and i/o of boxer-6614 boxer-6614- a1 -- + 12v dc usb 3.0

  • Page 18

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 3 boxer-6614- a1m usb 3.0

  • Page 19

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 4 boxer-6614- a2 -- + 12v dc usb 3.0

  • Page 20

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 5 boxer-6614- a2m usb 3 .0

  • Page 21

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 6 2.2 allocation of usb ports port 2(usb2.0 ) port 3(usb2.0 ) usb 3.0 port 0(usb3.0 ) port 1(usb2.0 ).

  • Page 22

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 7 2.3 connectors and jumpers of the main board component side.

  • Page 23

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 8 solder side.

  • Page 24

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 9 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function jp8 ...

  • Page 25

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 10 2.5 list of connectors the board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each board's connectors: label function c...

  • Page 26

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 11 cn34 ddr3l so-dimm slot cn35 uim card socket cn37 mini-card slot (full-mini card).

  • Page 27

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 12 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip...

  • Page 28

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 13 2.7 com2 pin8 function selection (jp8) 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 ...

  • Page 29

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 14 smb_data 1 6 gnd smb_clk gnd ps_on# +5vsb jp17 function 1-2 disable 2-3 enable (default) note 1: disable auto power button jp17(1-2) : need to use power button jp19(1-2) to power on the system. 2.10 clear ...

  • Page 30

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 15 3 smb_clk i/o +3.3v 4 gnd gnd 5 ps_on# out +3.3v 6 +5vsb pwr +5v 2.12 +5v output for sata hdd (cn4) +5v gnd pin pin name signal type signal level 1 +5v pwr +5v 2 gnd gnd 2.13 external +5vsb input (cn5) +5v...

  • Page 31

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 16 2.14 sata port1 (cn6) pin 1 pin 7 pin pin name signal type signal level 1 gnd gnd 2 sata_tx+ diff 3 sata_tx- diff 4 gnd gnd 5 sata_rx- diff 6 sata_rx+ diff 7 gnd gnd 2.15 external +12v input (cn7) +12v gnd...

  • Page 32

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 17 2.16 audio i/o port (cn9) mic_l 1 10 mic_r line_l_in line_r_in left_out right_out +5v_audio gnd_audio gnd_audio gnd_audio pin pin name signal type signal level 1 mic_l in 2 mic_r in 3 gnd_audio gnd 4 line_...

  • Page 33

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 18 3 nc 4 gnd gnd 5 nc 6 +1.5v pwr +1.5v 7 pcie_clk_req# in 8 nc 9 gnd gnd 10 nc 11 pcie_ref_clk- diff 12 nc 13 pcie_ref_clk+ diff 14 nc 15 gnd gnd 16 nc 17 nc 18 gnd gnd 19 nc 20 w_disable# out +3.3v 21 gnd ...

  • Page 34

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 19 27 gnd gnd 28 +1.5v pwr +1.5v 29 gnd gnd 30 smb_clk i/o +3.3v 31 pcie_tx- diff 32 smb_data i/o +3.3v 33 pcie_tx+ diff 34 gnd gnd 35 gnd gnd 36 usb_d- diff 37 gnd gnd 38 usb_d+ diff 39 +3.3vsb pwr +3.3v 40 ...

  • Page 35

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 20 lad0 1 12 lad1 lad2 lad3 lframe# lreset# ldrq0 ldrq1 serirq gnd lclk +3.3v 51 nc 52 +3.3vsb pwr +3.3v note 1: cn10 can be selected for mini-card or msata by changing bom. Note 2: you can choose the functio...

  • Page 36

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 21 9 lclk out 10 ldrq0 in 11 ldrq1 in 12 serirq i/o +3.3v 2.19 com port 2 connector (cn12 of mainboard) 1 5 6 9 pin pin name signal type signal level 1 dcd in 2 rx in 3 tx out ± 9v 4 dtr out ± 9v 5 gnd gnd 6 ...

  • Page 37

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 22 pin pin name signal type signal level 1 rs422_tx- out ± 5v 2 rs422_tx+ out ± 5v 3 rs422_rx+ in 4 rs422_rx- in 5 gnd gnd 9 nc/+5v/+12v pwr +5v/+12v rs-485 pin pin name signal type signal level 1 rs485_d-- i...

  • Page 38

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 23 2.20 lpt port (cn13) n.C n.C n.C n.C n.C gnd gnd gnd gnd gnd gnd gnd gnd n.C dio0 dio1 dio2 dio3 n.C n.C n.C n.C dio7 dio6 dio5 dio4 strobe# 1 2 25 26 1 2 25 26 afd# error# print# slin# gnd gnd gnd gnd gnd...

  • Page 39

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 24 16 gnd gnd 17 pd7 i/o 18 gnd gnd 19 ack# in 20 gnd gnd 21 busy in 22 gnd gnd 23 pe in 24 gnd gnd 25 slct in 26 nc 2.21 com port 3 connector (cn14 of mainboard) 1 5 6 9 pin pin name signal type signal level...

  • Page 40

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 25 7 rts out ± 9v 8 cts in 9 ri in rs-422 pin pin name signal type signal level 1 rs422_tx- out ± 5v 2 rs422_tx+ out ± 5v 3 rs422_rx+ in 4 rs422_rx- in 5 gnd gnd 9 nc/+5v/+12v pwr +5v/+12v rs-485 pin pin name...

  • Page 41

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 26 9 nc/+5v/+12v pwr +5v/+12v note : com 3 can be configured into rs-232/422/485 through bios settings. Default is rs-232 2.22 com port 4 (cn15 of mainboard) 1 5 6 9 pin pin name signal type signal level 1 dc...

  • Page 42

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 27 2.23 digital io port (cn16) dio1 dio3 dio5 dio7 gnd dio0 1 2 9 10 dio2 dio4 dio6 +5v pin pin name signal type signal level 1 dio0 i/o +5v 2 dio1 i/o +5v 3 dio2 i/o +5v 4 dio3 i/o +5v 5 dio4 i/o +5v 6 dio5 ...

  • Page 43

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 28 pin pin name signal type signal level 1 +5vsb pwr 2 usb3_d- diff 3 usb3_d+ diff 4 gnd gnd 5 gnd gnd 2.25 usb 2.0 port 2 (cn18) +5vsb usb2_d- usb2_d+ gnd gnd pin pin name signal type signal level 1 +5vsb pw...

  • Page 44

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 29 pin pin name signal type signal level 1 +5vsb pwr +5v 2 usb0_d- diff 3 usb0_d+ diff 4 gnd gnd 5 +5vsb pwr +5v 6 usb0_d- diff 7 usb0_d+ diff 8 gnd gnd 2.27 bios debug port (cn19) pin1 pin3 pin5 pin7 pin2 pi...

  • Page 45

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 30 8 nc 2.28 ps/2 keyboard/mouse combo port (cn22) kb_clk kb_data 1 5 6 2 ms_data +5vsb gnd ms_clk pin pin name signal type signal level 1 kb_ data i/o +5v 2 kb_clk i/o +5v 3 gnd gnd 4 +5vsb pwr +5v 5 ms_data...

  • Page 46

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 31 pin pin name signal type signal level 1 +5vsb pwr +5v 2 usb0_d- diff 3 usb0_d+ diff 4 gnd gnd 5 usb0_ssrx− diff 6 usb0_ssrx+ diff 7 gnd gnd 8 usb0_sstx− diff 9 usb0_sstx+ diff 10 +5vsb pwr +5v 11 usb1_d- d...

  • Page 47

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 32 2.30 lan (rj-45) port1 (cn26) 1 act/link led speed led 8 pin pin name signal type signal level 1 mdi0+ diff 2 mdi0- diff 3 mdi1+ diff 4 mdi2+ diff 5 mdi2- diff 6 mdi1- diff 7 mdi3+ diff 8 mdi3- diff 2.31 l...

  • Page 48

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 33 2 mdi0- diff 3 mdi1+ diff 4 mdi2+ diff 5 mdi2- diff 6 mdi1- diff 7 mdi3+ diff 8 mdi3- diff 2.32 com port 1 (d-sub 9) (cn28) 1 5 6 9 pin pin name signal type signal level 1 dcd in 2 rx in 3 tx out ± 9v 4 dt...

  • Page 49

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 34 2.33 hdmi port (cn29) 1 2 18 19 pin pin name signal type signal level 1 tmds_dat2+ diff 2 gnd gnd 3 tmds_dat2- diff 4 tmds_dat1+ diff 5 gnd gnd 6 tmds_dat1- diff 7 tmds_dat0+ diff 8 gnd gnd 9 tmds_dat0- di...

  • Page 50

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 35 2.34 vga port (cn30) 1 6 10 11 15 5 pin pin name signal type signal level 1 red out 2 green out 3 blue out 4 nc 5 gnd gnd 6 red_gnd_rtn gnd 7 green_gnd_rtn gnd 8 blue_gnd_rtn gnd 9 +5v pwr +5v 10 crt_plug#...

  • Page 51

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 36 2.35 battery (cn31) pin pin name signal type signal level 1 +3.3v pwr 3.3v 2 gnd gnd 2.36 cfast slot (cn33) pin pin name signal type signal level s1 gnd gnd s2 sata_tx+ diff s3 sata_tx- diff s4 gnd gnd s5 ...

  • Page 52

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 37 pc11 nc pc12 nc pc13 +3.3v pwr +3.3v pc14 +3.3v pwr +3.3v pc15 gnd gnd pc16 gnd gnd pc17 nc 2.37 ddr3l so-dimm slot (cn34) standard specification 2.38 uim card socket (cn35) pin pin name signal type signal...

  • Page 53

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 38 3 nc 4 gnd gnd 5 nc 6 +1.5v pwr +1.5v 7 pcie_clk_req# in 8 uim_pwr pwr 9 gnd gnd 10 uim_data i/o 11 pcie_ref_clk- diff 12 uim_clk in 13 pcie_ref_clk+ diff 14 uim_rst in 15 gnd gnd 16 uim_vpp pwr 17 nc 18 g...

  • Page 54

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 39 27 gnd gnd 28 +1.5v pwr +1.5v 29 gnd gnd 30 smb_clk i/o +3.3v 31 pcie_tx- diff 32 smb_data i/o +3.3v 33 pcie_tx+ diff 34 gnd gnd 35 gnd gnd 36 usb_d- diff 37 gnd gnd 38 usb_d+ diff 39 +3.3vsb pwr +3.3v 40 ...

  • Page 55

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 40 51 nc 52 +3.3vsb pwr +3.3v.

  • Page 56

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 41 2.40 hard disk drive installation (a2/a2m) step 1: remove the baseplate as instructed below.

  • Page 57

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 42 step 2: place the hdd on the bracket plate step 3: tighten the screws at the back to secure the hdd.

  • Page 58

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 43 step 4: connect the sata and power cables to the hdd, attach the hdd assembly to the baseplate..

  • Page 59

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 44 2.41 ram installation (a1/a1m) step 1: remove the screws on the baseplate step 2: remove the screw on the front panel as shown below.

  • Page 60

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 45 step 3: remove the screw on the rear panel as shown below step 4: remove the baseplate, insert the ram into the ram slot.

  • Page 61

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 46 step 5: push down to secure the ram step 6: place a thermal pad over the ram.

  • Page 62

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 47 step 7: close and secure the baseplate step 8: close and secure the front panel as shown below.

  • Page 63

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 48 step 9: close and secure the rear panel as shown below.

  • Page 64

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 49 2.42 ram installation (a2/a2m) step 1: remove the baseplate as instructed below.

  • Page 65

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 50 step 2: insert the ram into the ram slot step 3: push down to secure the ram.

  • Page 66

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 51 step 4: close the baseplate as instructed below.

  • Page 67

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 52 2.43 cfast tm installation (a1/a1m/a2/a2m) step 1: insert a cfast tm card into the cfast tm slot step 2: lower the arm to secure the cfast tm card.

  • Page 68

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 2 hardware installation 2 - 53 2.44 wallmount installation step 1: attach the brackets we suggest using this screw..

  • Page 69: Ami

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 ami bios setup chapter 3 chapter 3 award bios setup 3-1.

  • Page 70

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of erro...

  • Page 71

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 3.2 ami bios setup ami bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information when the power is tu...

  • Page 72

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 bios setup menu main press ‘delete’ key to enter setup chapter 3 ami bios setup 3-4.

  • Page 73

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced chapter 3 award bios setup 3-5.

  • Page 74

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> power management options summary: power mode atx type optimal default, failsafe default at type select power supply mode restore ac power loss last state optimal default, failsafe default power on power off select ac power state whe...

  • Page 75

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 enables or disables bios acpi auto configuration enable hibernation enable optimal default, failsafe default disable enables or disables system ability to hibernate (os/s4 sleep state). This option may be not effective with some os lock legacy ...

  • Page 76

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> power management -> s5 rtc wake settings options summary: wake system with fixed time enable disable optimal default, failsafe default wake up hour 0 wake up minute 0 wake up second 0 wake system with dynamic time enable disable opt...

  • Page 77

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 select rtc wake mode advanced -> super io configuration chapter 3 award bios setup 3-9.

  • Page 78

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> super io configuration serial port 1 configuration chapter 3 ami bios setup 3-10

  • Page 79

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> super io configuration serial port 2 configuration chapter 3 award bios setup 3-11.

  • Page 80

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> super io configuration serial port 3 configuration chapter 3 ami bios setup 3-12.

  • Page 81

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> super io configuration serial port 4 configuration options summary: serial port disabled enabled default allows bios to en/disable correspond serial port. Change settings (serial port 1) auto default io=3f8h; irq=4; io=3f8h; irq=3,4...

  • Page 82

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 io=3e8h; irq=3,4,5,6,7,9,10,11,12; io=2e8h; irq=3,4,5,6,7,9,10,11,12; allows bios to select serial port resource. Change settings (serial port 2) auto default io=2f8h; irq=3; io=3f8h; irq=3,4,5,6,7,9,10,11,12; io=2f8h; irq=3,4,5,6,7,9,10,11,12;...

  • Page 83

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 io=2e8h; irq=3,4,5,6,7,9,10,11,12; io=3e8h; irq=3,4,5,6,7,9,10,11,12; io=2e8h; irq=3,4,5,6,7,9,10,11,12; working model rs232 default rs422 rs485 select working model change settings (serial port 4) auto default io=2e8h; irq=7; io=3f8h; irq=3,4,...

  • Page 84

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 enable or disable smart fan advanced -> h/w monitor chapter 3 ami bios setup 3-16.

  • Page 85

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> h/w monitor options summary: intel virtualization technology disabled enabled optimal default, failsafe default when enabled, a vmm can utilize the additional hardware capabilities provided by vander pool technology chapter 3 award ...

  • Page 86

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> cpu configuration socket 0 cpu information chapter 3 ami bios setup 3-18.

  • Page 87

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> sata configuration options summary: sata mode ide default ahci ide: configure sata controllers as legacy ide ahci: configure sata controllers to operate in ahci mode en/disable sata port chapter 3 award bios setup 3-19.

  • Page 88

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> csm configuration chapter 3 ami bios setup 3-20

  • Page 89

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> trusted computing chapter 3 award bios setup 3-21.

  • Page 90

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 advanced -> usb configuration options summary: legacy usb support enabled optimal default, failsafe default disabled auto enables bios support for legacy usb support. When enabled, usb can be functional in legacy environment like dos. Auto opti...

  • Page 91

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 hard disk cdrom if auto. Usb devices less than 530mb will be emulated as floppy and remaining as floppy and remaining as hard drive. Forced fdd option can be used to force a hdd formatted drive to boot as fdd(ex. Zip drive) chipset chapter 3 aw...

  • Page 92

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chipset -> host bridge chapter 3 ami bios setup 3-24.

  • Page 93

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chipset -> south bridge chapter 3 award bios setup 3-25.

  • Page 94

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chipset -> south bridge -> azallia hd audio azalia hd audio disabled hd audio optimal default, failsafe default enabling/disabling hd audio controller. Chipset -> south bridge -> usb configuration chapter 3 ami bios setup 3-26.

  • Page 95

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chapter 3 award bios setup 3-27.

  • Page 96

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 chipset -> south bridge -> pci express configuration options summary: pci express root port 0 disabled enabled optimal default, failsafe default enabling/disabling pci express root ports pci express root port x disabled enabled auto optimal def...

  • Page 97

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 security setup submenu: security change user/supervisor password you can install a supervisor password, and if you install a supervisor password, you can then install a user password. A user password does not provide access to many of the featu...

  • Page 98

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 removing the password highlight this item and type in the current password. At the next dialog box press enter to disable password protection. Boot options summary: quiet boot disabled enabled default en/disable showing boot logo. Launch i210/i...

  • Page 99

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 en/disable pxe boot for 8111e lan exit chapter 3 award bios setup 3-31.

  • Page 100: Driver

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 driver installation chapter 4 chapter 4 driver installation 4-1.

  • Page 101

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 the boxer-6614 comes with a dvd-rom that contains all drivers and utilities that meet your needs. Follow the sequence below to install the drivers: step 1 – install chipset driver step 2 – install graphics driver step 3 – install lan driver ste...

  • Page 102

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 4.1 installation: insert the boxer-6614 dvd-rom into the dvd-rom drive. And install the drivers from step 1 to step 9 in order. Step 1 – install chipset driver 1. Click on the step1 - chipset folder and double click on the setupchipset.Exe file...

  • Page 103

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 win7_8-32_64_r273.Exe file 2. Follow the instructions that the window shows 3. The system will help you install the driver automatically step 5 – install txe driver 1. Click on the step5 - txe folder and double click on the setuptxe.Exe file 2....

  • Page 104

    E m b e d d e d c o n t r o l l e r b o x e r - 6 6 1 4 folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatically step 9 – install usb3.0 driver 1. Click on the step9 - usb3.0 folder and double click on the setup.Exe file follow the instruct...

  • Page 105: Programming The

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 programming the watchdog timer appendix a appendix a programming the watchdog timer a-1.

  • Page 106

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 a.1 watchdog timer registers table 1 : watch dog relative io address i/o base address default value note 0xa00 i/o base address for watchdog operation. This address is assigned by sio ldn7, register 0x60‐0x61. Table 2 : watchdog relative register t...

  • Page 107

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 counting unit 0x05 3 0 select time unit. 0: second 1: minute output signal type 0x05 4 1 0: level 1: pulse must set this bit to 1 watchdog timer enable 0x05 5 1 0: disable 1: enable timeout status 0x05 6 1 1: timeout occurred. Write a 1 to clear ti...

  • Page 108

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 a.2 watchdog sample program *********************************************************************// wdt i/o operation relative definition (please reference to table 1) #define wdtaddr 0xa00 // wdt i/o base address void wdtwritebyte(byte register, b...

  • Page 109

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 ********************************************************************* void main(){ // procedure : aaeonwdtconfig // (byte)timer : counter of wdt timer.(0x00~0xff) // (boolean)unit : select time unit(0: second, 1: minute). Aaeonwdtconfig(counter, un...

  • Page 111: I/o Information

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 i/o information appendix b appendix b i/o information b - 1.

  • Page 112

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 b.1 i/o address map appendix b i/o information b - 2.

  • Page 113

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 b.2 memory address map appendix b i/o information b - 3.

  • Page 114

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 b.3 irq mapping chart appendix b i/o information b - 4.

  • Page 115

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 appendix b i/o information b - 5.

  • Page 116

    E m b e d d e d c o n t r o l l e r a e c - 6 6 1 4 b.4 dma channel assignments appendix b i/o information b - 6.