1. DL manuals
  2. Aaeon
  3. Motherboard
  4. EMB-9459T
  5. User Manual

Aaeon EMB-9459T User Manual - Quick

Manual is about: Rev.B Mini-ITX

Summary of EMB-9459T

  • Page 1

    M i n i - i t x e m b - 9 4 5 9 t r e v . B emb-9459t rev.B onboard intel ® atom tm n270 processor mini-itx realtek 8111c ethernet 8 usb2.0, 6 com, 1 parallel 1 pci, 1 mini pci, 2 pci-e atx power type emb-9459t manual rev.B 2nd ed. August 2010

  • Page 2

    M i n i - i t x e m b - 9 4 5 9 t r e v . B copyright notice this document is copyrighted, 2010. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, c...

  • Page 3

    M i n i - i t x e m b - 9 4 5 9 t r e v . B acknowledgments all other products’ name or trademarks are properties of their respective owners. Z award is a trademark of award software international, inc. Z compactflash ™ is a trademark of the compact flash association. Z intel ® , atom tm are tradema...

  • Page 4

    M i n i - i t x e m b - 9 4 5 9 t r e v . B packing list (for standard only, not for bulk pack) before you begin installing your card, please make sure that the following materials have been shipped: z 1 1701400453 ide cable z 1 9657666600 jumper cap z 1 1709070500 serial ata cable z 1 1702151200 on...

  • Page 5

    M i n i - i t x e m b - 9 4 5 9 t r e v . B contents chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications ..............................

  • Page 6

    M i n i - i t x e m b - 9 4 5 9 t r e v . B 2.15 tv out connector (cn4)....................................... 2-13 2.16 lcd inverter connector (cn5, cn26) ................. 2-13 2.17 lvds lcd connector (cn6, cn7) ....................... 2-13 2.18 usb connector (cn8, cn9) ..............................

  • Page 7

    M i n i - i t x e m b - 9 4 5 9 t r e v . B b.3 irq mapping chart ................................................B-4 b.4 dma channel assignments.……………………… .B-4 appendix c mating connector c.1 list of mating connectors and cables.................. C-2 vi.

  • Page 8: General

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 1 general information 1- 1 general chapter 1 information.

  • Page 9

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 1 general information 1-2 1.1 introduction the emb-9459t rev.B supports intel ® atom tm n270 processor which when paired with the intel ® 945gse + ich7m chipset offers a high performance computing platform with low power consumption. This new produ...

  • Page 10

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 1 general information 1-3 1.2 features z onboard intel ® atom tm n270 processor (fanless) z intel ® 945gse + ich7m z ddrii 400/533 memory, max. 2gb z gigabit ethernet x 2 or 10/100base-tx x 2 z crt, tv-out, dvi, 18-bit dual-channel lvds and 2 nd 18...

  • Page 11

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 1 general information 1-4 1.3 specifications system z processor supports onboard intel ® atom tm n270 processor 1.6ghz, fsb533mhz z system memory 240-pin ddrii dimm x 1, ddrii 400/533 up to 2gb z chipset intel ® 945gse + ich7m z i/o chipset ite8712...

  • Page 12

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 1 general information 1-5 z battery lithium battery z power requirement at/atx z power consumption (typical) intel ® atom tm n270 0.65a @ +12v, 1.02a @ +5v z board size 6.7”(l) x 6.7”(w) (170 mm x 170 mm) z gross weight 1.2 lb (0.5 kg) z operating ...

  • Page 13

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 1 general information 1-6 standard, s-terminal and composite video z dvi dvi-i x 1 i/o z storage eide x 1 (udma100 for one device, slave only), sata ii x 2, type ii compactflash x 1 z serial port rs-232 x 5, rs-232/422/485 x 1 z audio mic-in, line-...

  • Page 14: Quick

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 1 quick installation chapter 2 guide notice: the quick installation guide is derived from chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual cd-rom that...

  • Page 15

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 2 2.1 safety precautions always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive e...

  • Page 16

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 3 2.2 location of connectors and jumpers component side.

  • Page 17

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 4 solder side.

  • Page 18

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 5 2.3 mechanical drawing component side.

  • Page 19

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 6 solder side.

  • Page 20

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 7 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function jp1 1 st 18-b...

  • Page 21

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 8 2.5 list of connectors the board has a number of connectors that allow you to configure your system to suit your application. The table below shows the function of each of the board's connectors: label function audi...

  • Page 22

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 9 cn12 com 5 rs-232 serial port connector cn13 com 6 rs-232 serial port connector cn14 digital i/o cn15 com 4 rs-232 serial port connector cn16 com 3 rs-232 serial port connector cn19 3-pin +12v fan connector cn20 fro...

  • Page 23

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 10 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often p...

  • Page 24

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 11 2.7 lcd inverter voltage selection (jp1-18 bits, jp7-24 bits) jp1/jp7 function 1-2 +5v (default) 2-3 +12v 2.8 com2 ring/+5v/+12v selection (jp2) jp2 function 1-2 +12v 3-4 +5v 5-6 ring (default) 2.9 lcd voltage sele...

  • Page 25

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 12 note: the max. Rating of pin 1 is 12v @ 1a the max. Rating of pin 4 is 5v @ 1a 2.13 audio 2watt speaker output (cn2) pin signal 1 spk- r+ 2 spk- r- 3 spk- l+ 4 spk- l- 2.14 com1 rs-232 & com2 rs-232/422/485 serial ...

  • Page 26

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 13 7 rts 8 cts 9 ri/+5v/+12v 2.15 tv output connector (cn4) pin signal pin signal 1 y 2 cvbs 3 gnd 4 gnd 5 c 6 n.C 7 gnd 8 n.C 2.16 lcd inverter connector (cn5, cn26) pin signal 1 vcc of lcd inverter (+5v/+12v) 2 adju...

  • Page 27

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 14 17 i2c_data 18 i2c_clk 19 lvds2_tx0- 20 lvds2_tx0+ 21 lvds2_tx1- 22 lvds2_tx1+ 23 lvds2_tx2- 24 lvds2_tx2+ 25 lvds2_tx3-(cn6-24bit only) 26 lvds2_tx3+(cn6-24bit only) 27 ppvcc 28 gnd 29 lvds2_txclk- 30 lvds2_txclk+...

  • Page 28

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 15 21 busy 22 gnd 23 pe 24 gnd 25 select 26 n.C 2.20 com5, com6, com4, com3 rs-232 serial port connector (cn12, cn13, cn15, cn16) pin signal pin signal 1 dcd 2 rxd 3 txd 4 dtr 5 gnd 6 dsr 7 rts 8 cts 9 ri 10 n.C 2.21 ...

  • Page 29

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 16 msb lsb 8 in pin1 pin2 pin3 pin4 pin5 pin6 pin7 pin8 gpi 27 gpi 26 gpi 25 gpi 24 gpi 23 gpi 22 gpi 21 gpi 20 msb lsb 8 out pin1 pin2 pin3 pin4 pin5 pin6 pin7 pin8 gpo 27 gpo 26 gpo 25 gpo 24 gpo 23 gpo 22 gpo 21 gp...

  • Page 30

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 17 4 gnd 5 lfeout 6 cenout 2.25 atx power connector (cn25) pin signal pin signal 1 n.C. 11 n.C. 2 n.C. 12 n.C. 3 gnd 13 gnd 4 +5v 14 ps_on 5 gnd 15 gnd 6 +5v 16 gnd 7 gnd 17 gnd 8 power ok 18 n.C. 9 +5vsb 19 +5v 10 +1...

  • Page 31

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 2 quick installation guide 2 - 18 below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon main board/ daughter board/ backplane 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ...

  • Page 32: Award

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 3 award bios setup 3-1 award chapter 3 bios setup.

  • Page 33

    M i n i - i t x e m b - 9 4 5 9 t r e v . B 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal an...

  • Page 34: Entering Setup

    M i n i - i t x e m b - 9 4 5 9 t r e v . B 3.2 award bios setup awards bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information when the power is turned of...

  • Page 35: Frequency/voltage Control

    M i n i - i t x e m b - 9 4 5 9 t r e v . B frequency/voltage control use this menu to specify your settings for auto detect dimm/pci clock and spread spectrum. Load fail-safe defaults use this menu to load the bios default values for the minimal/stable performance for your system to operate. Load o...

  • Page 36: Driver

    M i n i - i t x e m b - 9 4 5 9 t r e v . B chapter 4 driver installation 4 -1 driver chapter 4 installation ..

  • Page 37

    M i n i - i t x e m b - 9 4 5 9 t r e v . B the emb-9459t rev.B comes with an autorun cd-rom that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver cd, the driver cd-title will auto start and show the installation guide. If not, please follow...

  • Page 38

    M i n i - i t x e m b - 9 4 5 9 t r e v . B 4.1 installation: insert the emb-9459t rev.B cd-rom into the cd-rom drive. And install the drivers from step 1 to step 5 in order. Step 1 – install inf driver 1. Click on the step 1 – inf folder and select the os folder your system is 2. Double click on th...

  • Page 39

    M i n i - i t x e m b - 9 4 5 9 t r e v . B step 4 –install lan driver 1. Click on the step 4 –lan folder and select the os folder your system is 2. Double click on the setup.Exe located in each os folder 3. Follow the instructions that the window shows 4. The system will help you install the driver...

  • Page 40: Programming The

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-1 programming the appendix a watchdog timer.

  • Page 41

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-2 a.1 programming emb-9459t rev.B utilizes ite 8712 chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the aaeon intial watchdog timer program is also attached ba...

  • Page 42

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-3 there are three steps to complete the configuration setup: (1) enter the mb pnp mode; (2) modify the data of configuration registers; (3) exit the mb pnp mode. Undesired result may occur if the mb pnp mode is n...

  • Page 43

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-4 watchdog timer configuration registers configure control (index=02h) this register is write only. Its values are not sticky; that is to say, a hardware reset will automatically clear the bits, and does not requ...

  • Page 44

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-5 watchdog timer configuration register (index=72h, default=00h) watchdog timer time-out value register (index=73h, default=00h).

  • Page 45

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-6 a.2 it8712 watchdog timer initial program .Model small .Code main: call enter_configuration_mode call check_chip mov cl, 7 call set_logic_device ;time setting mov cl, 10 ; 10 sec dec al watch_dog_setting: ;time...

  • Page 46

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-7 ; game port enable mov cl, 9 call set_logic_device initial_ok: call exit_configuration_mode mov ah,4ch int 21h enter_configuration_mode proc near mov si,word ptr cs:[offset cfg_port] mov dx,02eh mov cx,04h init...

  • Page 47

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-8 ret exit_configuration_mode endp check_chip proc near mov al,20h call read_configuration_data cmp al,87h jne not_initial mov al,21h call read_configuration_data cmp al,12h jne not_initial need_initial: stc ret ...

  • Page 48

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-9 mov dx,word ptr cs:[cfg_port+06h] in al,dx ret read_configuration_data endp write_configuration_data proc near mov dx,word ptr cs:[cfg_port+04h] out dx,al xchg al,ah mov dx,word ptr cs:[cfg_port+06h] out dx,al ...

  • Page 49

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix a programming the watchdog timer a-10 push ax push cx xchg al,cl mov cl,07h call superio_set_reg pop cx pop ax ret set_logic_device endp ;select 02eh->index port, 02fh->data port cfg_port db 087h,001h,055h,055h dw 02eh,02fh end main note: interrup...

  • Page 50: I/o Information

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix b i/o information b-1 i/o information appendix b.

  • Page 51

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix b i/o information b-2 b.1 i/o address map.

  • Page 52

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix b i/o information b-3 b.2 memory address map.

  • Page 53

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix b i/o information b-4 b.3 irq mapping chart b.4 dma channel assignments.

  • Page 54: Mating Connecotor

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix c mating connector c - 1 mating connecotor appendix c.

  • Page 55

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix c mating connector c - 2 c.1 list of mating connectors and cables the table notes mating connectors and available cables. Mating connector connector label function vendor model no. Available cable cable p/n cn1 dvi+vga connector astron 45pin-90d- ...

  • Page 56

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix c mating connector c - 3 cn8 usb4 & usb5 connector catch 2.00mm pitch 10 pins ( catch h754-2x5 or compatible) usb cable 1709100208 cn9 usb2 & usb3 connector catch 2.00mm pitch 10 pins ( catch h754-2x5 or compatible) usb cable 1709100208 cn10 lpt p...

  • Page 57

    M i n i - i t x e m b - 9 4 5 9 t r e v . B appendix c mating connector c - 4 0-03s or compatible) cn20 front panel connector ho- base 2.54mm pitch 10 pins ( ho-base 2541-2h-2x5 or compatible) n/a n/a cn23 spdif connector catch 2.00mm pitch 3 pins (catch 1192-700-03s or compatible) spdif cable 17090...