1. DL manuals
  2. Aaeon
  3. Motherboard
  4. EMB-LN9T
  5. Manual

Aaeon EMB-LN9T Manual

Manual is about: Intel AtomTM N450/D510 Processor Mini-ITX Realtek 8111C/ 8102E Ethernet 8 USB2.0, 6 COM, 1 Parallel 1 PCI, 1 Mini PCI, 1 Mini Card

Summary of EMB-LN9T

  • Page 1

    M i n i - i t x e m b - l n 9 t emb-ln9t intel ® atom tm n450/d510 processor mini-itx realtek 8111c/ 8102e ethernet 8 usb2.0, 6 com, 1 parallel 1 pci, 1 mini pci, 1 mini card emb-ln9t manual rev.A 1 st ed. September 2010

  • Page 2

    M i n i - i t x e m b - l n 9 t copyright notice this document is copyrighted, 2010. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, trans...

  • Page 3

    M i n i - i t x e m b - l n 9 t acknowledgments all other products’ name or trademarks are properties of their respective owners. Z award is a trademark of award software international, inc. Z compactflash ™ is a trademark of the compact flash association. Z intel ® , atom tm are trademarks of intel...

  • Page 4

    M i n i - i t x e m b - l n 9 t packing list (standard, not bulk pack) before you begin installing your card, please make sure that the following materials have been shipped: z 1 9657666600 jumper cap z 1 1709070500 serial ata cable z 1 1702151200 onboard serial ata power cable z 1 m209459000 metal ...

  • Page 5

    M i n i - i t x e m b - l n 9 t contents chapter 1 general information 1.1 introduction................................................................ 1-2 1.2 features .................................................................... 1-3 1.3 specifications ..........................................

  • Page 6

    M i n i - i t x e m b - l n 9 t 2.17 lvds backlight connector (cn7) ......................... 2-12 2.18 sata power connector (cn8) ............................. 2-12 2.19 atx power +12v connector (cn9) ...................... 2-13 2.20 com7~10 rs-232 serial port connector (cn10) 2-13 2.21 front panel...

  • Page 7

    M i n i - i t x e m b - l n 9 t b.2 memory address map............................................B-3 b.3 irq mapping chart ................................................B-4 b.4 dma channel assignments.……………………… .B-4 appendix c mating connector c.1 list of mating connectors and cables................

  • Page 8: General

    M i n i - i t x e m b - l n 9 t chapter 1 general information 1- 1 general chapter 1 information.

  • Page 9

    M i n i - i t x e m b - l n 9 t chapter 1 general information 1-2 1.1 introduction the emb-ln9t supports intel ® atom™ n450/d510 processor which when paired with the intel ® ich8m chipset offers a high performance computing platform with low power consumption. This new product supports two 200-pin d...

  • Page 10

    M i n i - i t x e m b - l n 9 t chapter 1 general information 1-3 1.2 features z onboard intel ® atom™ n450/d510 processor (fanless with n450) z intel ® ich8m z ddr2 667/800 sodimm x 2, max. 4gb z gigabit ethernet x 2 or 10/100base-tx x 2 z vga, 18-bit single channel lvds or optional 24-bit single c...

  • Page 11

    M i n i - i t x e m b - l n 9 t chapter 1 general information 1-4 1.3 specifications system z processor onboard intel ® atom tm n450/d510 processor (fanless with n450) z system memory 200-pin ddr2 sodimm x 2, ddr2 667/800, max. 4gb z chipset intel ® ich8m z i/o chipset winbond w83627uhg z ethernet r...

  • Page 12

    M i n i - i t x e m b - l n 9 t chapter 1 general information 1-5 z operating humidity 0%~90% relative humidity, non-condensing display: supports crt/lcd, crt/dvi simultaneous / dual view displays z chipset intel ® n450/d510 integrated, integrates hardware mpeg2 decoder z memory shared system memory...

  • Page 13: Quick

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 1 quick installation chapter 2 guide notice: the quick installation guide is derived from chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual cd-rom that came with t...

  • Page 14

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 2 2.1 safety precautions always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic co...

  • Page 15

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 3 2.2 location of connectors and jumpers component side.

  • Page 16

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 4 solder side.

  • Page 17

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 5 2.3 mechanical drawing component side.

  • Page 18

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 6 solder side.

  • Page 19

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 7 2.4 list of jumpers the board has a number of jumpers that allow you to configure your system to suit your application. The table below shows the function of each of the board's jumpers: label function jp1 lcd voltage selection...

  • Page 20

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 8 cn11 front panel connector cn12 mini card connector cn13 sim socket kbms1 ps2 keyboard/mouse connector com1 com1 rs-232 & com2 rs-232/422/485 serial port connector com3 com3 rs-232 serial port connector com4 com4 rs-232 serial ...

  • Page 21

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 9 2.6 setting jumpers you configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a...

  • Page 22

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 10 2.7 lcd voltage selection (jp1) jp1 function 1-2 +5v 2-3 +3.3v (default) 2.8 lcd backlight control selection (jp2) backlight control jp2 function 1-3 chips control 3-5 smbus control (default) backlight voltage jp2 function 2-4...

  • Page 23

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 11 2.12 spdif connector (cn2) pin signal 1 spdif-out 2 gnd 3 spdif-in 2.13 internal audio 2 channel connector (cn3) pin signal 1 speak-out r+ 2 speak-out r- 3 speak-out l+ 4 speak-out l- 2.14 lvds connector (cn4) pin signal pin s...

  • Page 24

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 12 29 n.C 30 n.C note: for vlcd (pin 3, 7, 27), the max. Rating of each pin is 0.5a@5v. 2.15 internal ps2 keyboard and mouse connector (cn5) pin signal 1 kbdata 2 kbclk 3 gnd 4 +5v 5 msdata 6 msclk 2.16 fan connector (cn6) pin si...

  • Page 25

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 13 2 gnd 3 gnd 4 +5v note: the max. Rating of pin1 is 1a @ 12v; the max. Rating of pin4 is 1a @ 5v. 2.19 atx power +12v connector (cn9) pin signal pin signal 1 gnd 2 gnd 3 +12v 4 +12v 2.20 com7~10 rs-232 serial port connector (cn...

  • Page 26

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 14 35 txd10 36 cts#10 37 dtr#10 38 ri#10 39 gnd 40 n.C 41 +5v 42 +5v 43 gnd 44 n.C 2.21 front panel connector (cn11) pin signal pin signal 1 power on button(-) 2 power on button(+) 3 ide led(-) 4 ide led(+) 5 external buzzer(-) 6...

  • Page 27

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 15 2.24 rs-232 serial port connector (com4) pin signal pin signal 1 dcd#4 2 rxd4 3 txd4 4 dtr#4 5 gnd 6 dsr#4 7 rts#4 8 cts#4 9 ri#4 10 n.C 2.25 rs-232 serial port connector (com5) pin signal pin signal 1 dcd#5 2 rxd5 3 txd5 4 dt...

  • Page 28

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 16 7 gnd 8 usbd5- 9 gnd 10 +5v 2.28 usb port connector (usb2) pin signal pin signal 1 +5v 2 gnd 3 usbd6- 4 gnd 5 usbd6+ 6 usbd6+ 7 gnd 8 usbd6- 9 gnd 10 +5v 2.29 lpt port connector (lpt1) pin signal pin signal 1 #strobe 2 #afd 3 ...

  • Page 29

    M i n i - i t x e m b - l n 9 t chapter 2 quick installation guide 2 - 17 below table for china rohs requirements 产品中有毒有害物质或元素名称及含量 aaeon main board/ daughter board/ backplane 有毒有害物质或元素 部件名称 铅 (pb) 汞 (hg) 镉 (cd) 六价铬 (cr(vi)) 多溴联苯 (pbb) 多溴二苯醚 (pbde) 印刷电路板 及其电子组件 × ○ ○ ○ ○ ○ 外部信号 连接器及线材 × ○ ○ ○ ○ ○ o：...

  • Page 30: Ami

    M i n i - i t x e m b - l n 9 t chapter 3 ami bios setup 3-1 ami chapter 3 bios setup.

  • Page 31

    M i n i - i t x e m b - l n 9 t 3.1 system test and initialization these routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal....

  • Page 32

    M i n i - i t x e m b - l n 9 t 3.2 ami bios setup ami bios rom has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed cmos ram so that it retains the setup information when the power is turned off. Entering setup...

  • Page 33: Driver

    M i n i - i t x e m b - l n 9 t chapter 4 driver installation 4 -1 driver chapter 4 installation ..

  • Page 34

    M i n i - i t x e m b - l n 9 t the emb-ln9t comes with an autorun cd-rom that contains all drivers and utilities that can help you to install the driver automatically. Insert the driver cd, the driver cd-title will auto start and show the installation guide. If not, please follow the sequence below...

  • Page 35

    M i n i - i t x e m b - l n 9 t 4.1 installation: insert the emb-ln9t cd-rom into the cd-rom drive. And install the drivers from step 1 to step 5 in order. Step 1 – install chipset driver 1. Click on the step 1 - chipset folder and double click on the infinst_autol.Exe file 2. Follow the instruction...

  • Page 36

    M i n i - i t x e m b - l n 9 t step 4 –install lan driver 1. Click on the step 4 - lan folder and select the os folder your system is 2. Double click on the setup.Exe located in each os folder 3. Follow the instructions that the window shows 4. The system will help you install the driver automatica...

  • Page 37: Programming The

    M i n i - i t x e m b - l n 9 t appendix a programming the watchdog timer a-1 programming the appendix a watchdog timer.

  • Page 38

    M i n i - i t x e m b - l n 9 t appendix a programming the watchdog timer a-2 a.1 programming emb-ln9t utilizes w83627uhg chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the aaeon intial watchdog timer program is also attached based on which you c...

  • Page 39

    M i n i - i t x e m b - l n 9 t appendix a programming the watchdog timer a-3 (3) exit the w83627uhg config mode. Undesired result may occur if the config mode is not exited normally. (1) enter the w83627uhg config mode to enter the w83627uhg config mode, two special i/o write operations are to be p...

  • Page 40

    M i n i - i t x e m b - l n 9 t appendix a programming the watchdog timer a-4 1 r/w 0: gpio5 is inactive. 1: gpio5 is active. 0 r/w 0: wdto# and pled are inactive. 1: wdto# and pled are inactive. Cr f5h. (wdto# and kbc p20 control mode register; default 00h) bit read/write description 7~5 reserved. ...

  • Page 41

    M i n i - i t x e m b - l n 9 t appendix a programming the watchdog timer a-5 01h: time-out occurs after 1 second/minute 02h: time-out occurs after 2 second/minutes 03h: time-out occurs after 3 second/minutes ………………………………………………….. Ffh: time-out occurs after 255 second/minutes cr f7h. (wdto# control ...

  • Page 42

    M i n i - i t x e m b - l n 9 t appendix a programming the watchdog timer a-6 a.2 w83627uhg watchdog timer initial program example: setting 10 sec. As watchdog timeout interval #include #include #define efer_port 0x2e #define entry_key 0x87 void main (void) { // set entry key outportb(efer_port,entr...

  • Page 43

    M i n i - i t x e m b - l n 9 t appendix a programming the watchdog timer a-7 // set watchdog time is 10 sec outportb(efer_port,0xf6); outportb(efer_port+1,0x0a); time is 10 sec outportb(efer_port,0xaa); exit }.

  • Page 44: I/o Information

    M i n i - i t x e m b - l n 9 t appendix b i/o information b-1 i/o information appendix b.

  • Page 45

    M i n i - i t x e m b - l n 9 t appendix b i/o information b-2 b.1 i/o address map.

  • Page 46

    M i n i - i t x e m b - l n 9 t appendix b i/o information b-3 b.2 memory address map.

  • Page 47

    M i n i - i t x e m b - l n 9 t appendix b i/o information b-4 b.3 irq mapping chart b.4 dma channel assignments.

  • Page 48: Mating

    M i n i - i t x e m b - l n 9 t appendix c mating connector c - 1 mating appendix c connector.

  • Page 49

    M i n i - i t x e m b - l n 9 t appendix c mating connector c - 2 c.1 list of mating connectors and cables the table notes mating connectors and available cables. Mating connector connector label function vendor model no. Available cable cable p/n cn2 spdif connector catch 2.00mm pitch 3 pins (catch...

  • Page 50

    M i n i - i t x e m b - l n 9 t appendix c mating connector c - 3 connector (com7~c om10) ( catch h754-2x22 or compatible) cn11 front panel connector hobase 2.54mm pitch 10 pins (ho-base 2541-2h-2x5 or compatible) n/a n/a com1 com1and com2 connector contek d-sub 9 connector dual port (contek.B-dg n1...

  • Page 51

    M i n i - i t x e m b - l n 9 t appendix c mating connector c - 4 compatible) dvi+vga1 dvi+vga connector astron 45pin-90d- dip (astron 1860044-006- r or compatible) n/a n/a lpt1 lpt port connector catch 2.00mm pitch 26 pins ( catch a003-268 or compatible) lpt cable 1701260200